Vivitek H5082 User Manual

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Starting and Shutting  down the Projector 
Starting the projector 
1.  Remove the lens cap. 
2.  Securely connect the power cord and 
signal cable. When connected, the 
power led will turn red. 
 
3.  Turn on the lamp by pressing “” 
button on the rear of the projector or 
“
” on the remote control. 
The PWR LED will now flash green.  
The startup screen will display in ap-
proximately 30 seconds. The first time 
you use the projector, you can select 
your preferred language from quick 
menu after the startup screen display. 
 
4.  
–  15  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
5.  Turn on your source that you want to 
display on the screen (computer, note-
book, video player, etc). The projector 
will detect the source automatically and 
will display on the screen. If not, push 
menu button and go to “SYSTEM 
SETUP: Basic”.  
Note: 
If you connected multiple sources at 
the same time, press the “Source” 
key on the remote control to switch 
between inputs.  
•  PC: Analog RGB / SCART / YPbPr via VGA input 
• HDMI 1/2/3: High Definition Multimedia Interface 
• COMPONENT: DVD input YCbCr / YPbPr, or 
HDTV input YPbPr 
 
• VIDEO: Traditional composite video 
• S-VIDEO: Super video (Y/C separated) 
Note: 
Turn on the projector first and then  select the signal sources. First time to turn on the projector: 
Remember to select the type of lens you have installed. 
Shutting down the Projector
1.  Press the “” button on the remote 
control or “
” button on the rear 
side of the projector two times with one 
second interval in between to turn off 
the projector. First push of button will 
display the following message on the 
screen. 
Press the button again to confirm the 
shut down. If the button is not pressed, 
the message will disappear in 5 seconds.
2.  The cooling fans continue to operate for about 60 seconds for cooling cycle and the PWR LED will turn or-
ange. 
When the light is solid orange, the projector has entered standby mode. 
If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle 
and has entered standby mode. Once in standby mode, simply press “
” button on the rear of the projec-
tor or “
” on the remote control to restart the projector. 
3.  Disconnect the power cord from the  electrical outlet and the projector. 
4.  Do not turn on the projector immediately following a power off procedure. 
– 16 – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
 Adjusting the  Projector Level 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
• Position the projector so that it is perpendicular to the screen. 
• Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection  
angle. 
• Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, twist 
the adjusters clockwise. 
2.  To lower the level of the projector, lift 
the projector and twist the adjusters 
counter clockwise. 
 
 
– 17  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
– 18 –  
Adjusting Projected Imag e Position Using Shift 
 
The Shift feature provides a lens shift function that  can be used to adjust the position of the projected 
image either horizontally or vertica lly within the range detailed below. 
Shift is a unique system that provid es lens shift while maintaining a much higher ANSI contrast ratio 
than traditional lens shift systems. 
Adjusting the vertical image position 
The vertical image height can be  adjusted between 120% and -40% of  half image height. Note that 
the maximum vertical image heigh t adjustment can be limited by the horizontal image position. For 
example it is not possible to ac hieve the maximum vertical image pos ition height detailed above if the 
horizontal image position is at ma ximum. Please consult the Shift Range diagram below for further 
clarification. 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
–  19  – 
Adjusting the horizontal image position 
With the lens in the center posit ion the horizontal image position can be adjusted to the left or right by 
up to a maximum of 10% of the half image width.  Note that the maximum horizontal image height ad-
justment can be limited by the vert ical image position. For example it is not possible to achieve the 
maximum horizontal image position if  the vertical image position is at maximum. Please consult the 
Shift Range diagram below for further clarification. 
 
Shift Range Diagram 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Adjusting the Zoom ring,  Focus and Keystone 
1.  Use the Image-zoom   
control (on the projector 
only) to resize the pro-
jected image and screen 
size. 
 
2.  Use the  Image-focus   
control (on the projector 
only) to sharpen the pro-
jected image. 
 
3.  Use the  KEYSTONE  
buttons (on the projector 
or the remote control) to 
correct image-trapezoid 
(wider top or bottom)  
effect. 
 
Remote control and OSD panel 
4.  The keystone control  
appears on the display. 
 
– 20 –  
Downloaded From projector-manual.com Vivitek Manuals 
						

							
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control curs or buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illu stration shows the corresponding buttons on the 
projector. 
 
1.  To enter the OSD, press the  MENU 
button.  
2.  There are six menus. Press the cur- sor ◄►  button to move through the 
menus.  
3. Press the cursor  ▲▼ button to move 
up and down in a menu.  
4. Press  ◄► to change values for set-
tings. 
5. Press  MENU to close the OSD or 
leave a sub menu. 
Note: 
Depending on the video source, not all items in  the OSD are available. For example, the PC Detail 
Adjustment item in the PICTURE: Basic menu can  only be modified when connected to a PC. 
Items that are not available cannot be accessed and are grayed out.  
— 21 — 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Setting the OSD Language 
Set the OSD language to your pr eference before continuing. 
1. Press the MENU button. Press the cursor  ◄► button to navigate to  SYSTEM SETUP: Basic . 
 
2. Press the cursor ▲▼ button until Language is highlighted.  
3. Press the cursor ◄►  button until the language you want is selected.  
4. Press the MENU button to close the OSD.   
– 22 – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
OSD Menu Overview 
Use the following illustration to quickly find a  setting or determine the range for a setting. 
 
– 23  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
PICTURE: Basic Menu 
Press the MENU  button to open the  OSD menu. Press the cursor  ◄► button to move to the 
PICTURE: Basic menu. Press the cursor  ▲▼ button to move up and down in the  PICTURE: Basic 
menu. Press ◄►  to change values for settings. 
Note: 
Customizeing the settings in PICTURE: Basic menu is only available in User 1/ 2/ 3 mode. 
 
ITEM DESCRIPTION 
Press the cursor ◄►  buttons to set the Display Mode.  
(Range: Movie/ Bright/ Normal/ User 1/ User 2/ User 3) 
Notes: ISF Day/ISF Night is availa ble when ISF Mode is on. 
Display Mode 
Press the cursor ◄► buttons to set the User Mode. 
(Range: Movie/ Bright/ Normal ) User Mode 
Brightness Press the cursor ◄►  buttons to adjust the display brightness. 
Contrast Press the cursor ◄► buttons to adjust the display contrast. 
Press the cursor ◄►  buttons to adjust the video saturation. 
Color Notes: This function is only available when Component, Video or S-Video input source is 
selected. 
Press the cursor ◄►  buttons to adjust the video tint/hue. 
Tint Notes: This function is only available when Component, Video or S-Video with NTSC  
system input source is selected. 
Press the cursor ◄►  buttons to adjust the display sharpness. 
Sharpness Notes: This function is only available when Component, Video or S-Video input source is 
selected. 
Press the  ENTER button to save all settings. Save Setting 
Press the  ENTER button to reset all settings to default values. Reset Picture Settings 
– 24 – 
Downloaded From projector-manual.com Vivitek Manuals