Vivitek D940vx Projector User Manual

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Tilt adjustor  Rotate adjuster lever to adjust angle position.  15 
2.  Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 
3.  Height adjustor Adjuster drops down when adjuster button is pushed. 
4.  Height adjustor button Push to release adjustor. 
15 
 
Note: 
When installing, ensure that you use only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw 
depth of 6 mm (0.23 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount 
load capacity must exceed the weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a 
period of 60 seconds. 
 
– 5 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Remote Control Parts 
 
Important: 
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the remote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have the same functions as the corresponding buttons on 
the remote control. This user’s manual describes the functions based on the remote control. 
– 6 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter Transmits signals to projector 
2.  Status LED Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up Up arrow when connected through USB to a PC 
5.  Right Right arrow when connected through USB to a PC 
6.  Down Down arrow when connected through USB to a PC 
7.  Page Down Page down when connected through USB to a PC 
8.  Up cursor  
9.  Right cursor  
10.  Down cursor 
Navigates and changes settings in the OSD  18 
11.  Volume +/- Adjusts volume 17 
12.  Mute Mutes the built-in speaker 
13.  Zoom+ Zoom in  
14.  Zoom- Zoom out 16 
15.  Freeze  Freeze/unfreezes the on-screen picture 
16.  Blank Makes the screen blank 
17.  Source Detects the input device 
18.  Auto Auto adjustment for phase, tracking, size, position 
19.  Menu Opens the OSD  18 
20.  Status Opens the OSD Status menu (the menu only opens when an 
input device is detected) 39 
21.  Keystone top/bottom Corrects image-trapezoid (wider top/bottom) effect 16 
22.  Left cursor Navigates and changes settings in the OSD  
23.  Enter Changes settings in the OSD 
24.  Page Up Page up when connected through USB to a PC 
25.  Left Left arrow when connected through USB to a PC 
26.  Enter Enter key when connected through USB to a PC 
18 
27.  Power  Turns the projector on or off 11 
28.  Laser Use as on-screen pointer. DO NOT POINT IN EYES. 
– 7 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the projector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using the remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote control; however, the buttons on the projector are lim-
ited in use.  
 
 
– 8 –  
						

							
SETUP AND OPERATION 
Inserting the Remote Control Batteries  
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries according to local ordinance regulations.  
 
3. Remove the batteries when not using the projector for prolonged periods. 
 
— 9 —  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Connecting Input Devices 
A PC or notebook computer and video devices can be connected to the projector at the same time. Video 
devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. 
Check the user manual of the connecting device to confirm it has the appropriate output connector.  
 
ITEM LABEL DESCRIPTION 
  (USB) Connect the USB CABLE from a computer. 
 VGA OUT Connect the RGB CABLE to a display. 
 LAN Connect a LAN CABLE from a computer 
 VGA IN – 1 Connect the RGB CABLE from a computer and components 
 VGA IN – 2 Connect the RGB CABLE from a computer. 
 
AUDIO IN 
AUDIO OUT 
Connect an AUDIO CABLE from the input device 
Connect an AUDIO CABLE for audio loop through 
 HDMI Connect an HDMI CABLE from an HDMI device 
 S-VIDEO Connect the S-VIDEO CABLE from a video device. 
 VIDEO Connect the COMPOSITE CABLE from a video device. 
 AUDIO IN (L and R) Connect the COMPOSITE CABLES from a video device  
 RS-232C Connect the RS-232 serial cable for remote control 
Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before making 
connections. 
– 10 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Starting and Shutting down the Projector 
1.  Connect the power cord to the projector. 
Connect the other end to a wall outlet. 
The  POWER and READY LEDs 
on the projector light. 
2.  Turn on the connected devices.  
3.  Ensure the READY LED displays a 
solid red and not a flashing red. Then 
press the  POWER button to turn on 
the projector.  
 
The projector splash screen displays and 
connected devices are detected. 
 
See Setting an Access Password 
(Security Lock) on page 13 if security 
lock is enabled. 
 
4.  If more than one input device is con-
nected, press the SOURCE button and 
use ▲▼ to scroll among devices. 
(Component is supported through the 
RGB to COMPONENT ADAPTER.) 
 
 
• VGA 1/VGA 2: Analog RGB 
Component: DVD input YCbCr / YPbPr, or 
HDTV input YPbPr via HD15 connector 
• Composite Video: Traditional composite video 
• S-Video: Super video (Y/C separated) 
• HDMI: HDMI, DVI 
– 11 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
5.  When the “Power Off? /Press Power 
again” message appears, press the 
POWER button. The projector turns 
off.  
Caution: 
1. Be sure to remove the lens cap before starting projector.  
2. Do not unplug the power cord until the READY LED stops flashing–indicating the projector has 
cooled down. 
 
 
 
– 12 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projec-
tor. When enabled, the password must be entered after you power on the projector. (See Navigating 
the OSD on page 18 and Setting the OSD Language on page 19 for help on using OSD menus.) 
Important: 
Keep the password in a safe place. Without the password, you will not be able to use the projector. 
If you lose the password, contact your reseller for information on clearing the password. 
 
1.  Press the MENU button to open the OSD 
menu. 
2.  Press the cursor ◄► button to move to 
the Installation I menu. 
 
 
 
3.  Press the cursor ▲▼ button to select  
Security Lock. 
4.  Press the cursor ◄► button to enable or 
disable security lock function. 
A password dialog box automatically  
appears. 
 
– 13 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
5.  You can use the cursor buttons ▲▼◄► 
either on keypad or IR remote control for 
password entry. You can use any 
combination including the same arrow five 
times, but not less than five. 
Press the cursor buttons in any order to set 
the password. Push the MENU button to 
exit the dialog box. 
 
 
6.  The password confirm menu appears when 
user presses the power-on key in case the 
Security Lock is enabled.  
Enter the password in the order you set it 
at step 5. In case you forget the password, 
please contact the service center.  
Service center will validate the owner and 
help reset the password.   
– 14 –