Vivitek D871st User Manual

DLP Projector – User’s Manual 
– 13  – 
 
Important: 
1.  Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the re mote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have...

DLP Projector—User’s Manual 
 
SETUP AND OPERATION 
Starting and Shutting down the Projector 
 
1.  Connect the power cord to the projector. 
Connect the other end to a wall outlet. 
The 
 POWER  LED on the projector 
light. 
2.  Turn on the connected devices.  
3.  Ensure the LAMP LED not a flashing. 
Then press the 
  POWER  button to 
turn on the projector.  
 
The projector splash screen displays and 
connected devices are detected. 
 
See  Setting an Access Password 
(Security Loc
 k) on page  16 if...

DLP Projector – User’s Manual 
4.  If more than one input device is con-
nected, press the SOURCE button and 
use  ▲▼  to scroll among devices. 
(Component is supported through the 
RGB to COMPONENT ADAPTER.) 
 For D860/D861  
Series 
 
  VGA: Analog RGB 
Component: DVD 
input YCbCr / 
YPbPr, or HDTV 
input YPbPr  
   Composite Video: Tradi-
tional composite video  For D862/D871/D873        
Series   VGA: Analog RGB 
   Component: DVD input 
YCbCr / YPbPr. 
   Composite Video: Tra-
ditional...

DLP Projector—User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See  Navigating the 
OSD  on page  20 and Setting the OSD Language  on page 21 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password,...

DLP Projector – User’s Manual 
5.  You can use the cursor buttons ▲▼◄► 
either on keypad or IR remote control for 
password entry. You can use any 
combination including the same arrow five 
times, but not less than five. 
Press the cursor buttons in any order to set 
the password. Push the  MENU button to 
exit the  dialog box. 
 
 
6.  The password confirm menu appears when 
user presses the power-on key in case the 
Security Lock  is enabled.  
Enter the password in the order you set it 
at step 5. In...

DLP Projector—User’s Manual 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
  The projector table or stand should be level and sturdy. 
   Position the projector so that it is perpendicular to the screen. 
   Ensure the cables are in a safe location. You could trip over them.  
 
To adjust the angle of the picture, turn  the tilt-adjuster right or left until the 
desired angle has been achieved. 
 
 
 
 
 
 
 
 
 
 
 
 
 
– 18 –   

DLP Projector – User’s Manual 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom   
control (on the projector 
only) to resize the pro-
jected image and screen 
size 
 (*) . 
2.  Use the 
Image-focus   
control (on the projector 
only) to sharpen the pro-
jected image 
 or . 
For D860/D861/D862 Series 
  For D871/D873 Series  
3.  Use the 
KEYSTONE  
buttons the remote control 
to correct image-trapezoid 
(wider top or bottom) ef-
fect. For D860/D861 Series 
  For D862/D871/D873 Series...

DLP Projector—User’s Manual 
 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote contro l cursor buttons to navigate and make changes to the OSD.  
                              
            
1.  To enter the OSD, press the 
MENU button.  
2.  There are five menus. Press  the cursor  ◄► button to 
move through the menus.  
3. Press the cursor  ▲▼ button 
to move...

DLP Projector – User’s Manual 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1.  Press the  MENU button. Press the cursor  ◄► button to navigate to Installation I. 
 
2.  Press the cursor  ▲▼ button until  Language is highlighted.  
 
3.  Press the cursor  ◄► button until the language you want is highlighted.  
4.   Press the  MENU button twice to close the OSD.   
 
 
 
 
 
 
 
 
 
 
 
–  21  –  

DLP Projector—User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
 
 
 
 
 
 
 
 
 
– 22 –