Vivitek D871st User Manual

DLP Projector – User’s Manual 
For D87 Series 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR receiver Receive IR signal from remote control 
2.  Lens Projection 
Lens 
3.  Focus ring Focuses the projected image 19 
4.   (POWER) 
See Top view—Power buttons and LEDs. 4 
Important: 
Ventilation openings on the projector 
allow for good air circulation, which keeps the projector lamp 
cool. Do not obstruct any of the ventilation openings. 
–3  –  

DLP Projector—User’s Manual 
Top view—Power buttons and LEDs 
 
ITEM LABEL DESCRIPTION SEE 
PAGE: 
1.   (POWER) 
Turns the projector On or Off  14 
On Lamp 
Error. 2.  LAMP LED 
Off Normal State 
Blue  Power On  
Off  Power Off (AC Off) 3.  POWER LED 
Flashing System Initialized / Cooling / Error code 
– 4 –  

DLP Projector – User’s Manual 
 Rear view 
Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before making 
connections. 
 
For D860/D861 Series 
 
 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  AC IN  Connect the POWER CABLE 14 
2.  AUDIO IN  Connect an AUDIO CABLE from the input device 
3.  VGA IN  Connect the RGB CABLE from a computer and components 
4.  VGA OUT Connect the RGB CABLE to a display 
5.  VIDEO IN  Connect the COMPOSITE CABLE from a video device...

DLP Projector—User’s Manual 
For D862/D871/D873 Series 
 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  AC IN Connect the POWER CABLE 14 
2.  S-VIDEO   Connect the S-VIDEO CABLE from a video device 
3.  VIDEO IN 
Connect the COMPOSITE CABLE from a video device  
4.  HDMITM  Connect the HDMITM CABLE from a HDMITM device 
5.  HDMITM  Connect the HDMITM CABLE from a HDMITM device 
6.    (USB)  Connect the USB CABLE from a computer  
7.  VGA IN   Connect the RGB CABLE from a computer 
8.  RS-232C  Connect RS-232...

DLP Projector – User’s Manual 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 
2.  Tilt adjustor  Rotate adjuster lever to adjust angle position.  18 
 
Note: 
When installing, ensure that you us e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of 12 mm (0.47 inch).  
The construction of the ceiling mount must be of a...

DLP Projector—User’s Manual 
Remote Control Parts  
For D860/D861 Series 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Up cursor Navigates and changes settings in the OSD   
2.  Enter  Changes settings in the OSD 
20 
3.  Power Turns the projector On or Off 14 
4.  Right cursor  Navigates and changes settings in the OSD 20 
5.  Volume + Increase volume 
6.  Volume - Decrease volume 
19 
7.  Blank  Video off and audio mute 
8.  Freeze Freeze/unfreezes the on-screen picture 
9.  Source Detects the input device...

DLP Projector – User’s Manual 
Inserting the Remote Control Batteries 
 
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow (A). Pull out the cover (B). 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution:  
1. Only use a 3V lithium battery (CR2025). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods....

DLP Projector—User’s Manual 
For D862/D871/D873 Series 
 
  
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter Transmits signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up Up arrow when connected through USB to a PC 
5.  Right  Right arrow when connected through USB to a PC 
6.  Down  Down arrow when connected through USB to a PC 
7.  Page Down  Page down when connected through USB to a PC 
8.  Up cursor  
9.  Right...

DLP Projector – User’s Manual 
– 11  – 
ITEM LABEL DESCRIPTION SEE PAGE: 
12.  Mute  Mutes the built-in speaker 
13.  Zoom+  Zoom in  
14.  Zoom- Zoom  out 
15.  Freeze  Freeze/unfreezes the on-screen picture 
16.  Blank Makes the screen blank 
17.  Source Detects the input device 
18.  Auto Auto adjustment for phase, tracking, size, position 
19.  Menu  Opens the OSD  20 
20.  Status  Opens the OSD Status menu (the menu only opens when an 
input device is detected) 41 
21.  Keystone top/bottom  Corrects...

DLP Projector—User’s Manual 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods. 
– 12 –