Vivitek D862 Projector User Manual

							DLP Projector – User’s Manual 
Using the Kensington® Lock 
Using the Kensington® Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
For D860/D861 Series 
 
 
 
For D862 Series 
 
 
 
Note: 
Contact your vendor for details on purchasing a suitable Kensi ngton security cable.  
The security lock corresponds to Kensington’s Micr oSaver Security System. If you have any com-
ment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242, 
http://www.Kensington.com. 
 
– 43  –  
						

							DLP Projector—User’s Manual 
Using the Security Bar 
In addition to the password protection function and the Kensington lock, the Security Bar helps pro-
tect the projector from unauthorized re moval. See the following picture. 
 
For D860/D861 Series 
 
 
 
For D862 Series 
 
 
– 44 –   
						

							DLP Projector – User’s Manual 
– 45  – 
 
TROUBLESHOOTING 
Common problems and solutions 
These guidelines provide tips to deal with problem s you may encounter while using the projector. If 
the problem remains unsolved, cont act your dealer for assistance. 
Often after time spent troubleshooting, the problem is  traced to something as simple as a loose con-
nection. Check the following before proceedi ng to the problem-specific solutions. 
  Use some other electrical device to confirm that the electrical outlet is working. 
   Ensure the projector is turned on. 
   Ensure all connections are securely attached.  
   Ensure the attached device is turned on. 
   Ensure a connected PC is not in suspending mode. 
   Ensure a connected notebook computer is configured for an external display. 
(This is usually done by pressing an Fn-key combination on the notebook.) 
Tips for Troubleshooting 
In each problem-specific section, tr y the steps in the order suggested. This may help you to solve the 
problem more quickly. 
Try to pin point the problem and thus  avoid replacing non-defective parts.  
For example, if you replace batteries and the problem remains, put the original batteries back and go 
to the next step.  
Keep a record of the steps you take when troubles hooting: The information may be useful when call-
ing for technical support or for passing on to service personnel. 
  
						

							DLP Projector—User’s Manual 
– 46 – 
LED Error Messages 
ERROR CODE MESSAGES POWER LED  
BLUE 
LAMP LED  
BLUE 
Standby mode  ON OFF 
System Initial  Flash OFF 
Over temperature  3 OFF 
Thermal break status error  4 OFF 
Lamp Fail  OFF ON 
Cooling Flashing  OFF 
Lamp temperature too high 5 3 
Case Open  7 OFF 
Color wheel error  9 OFF 
In the event of an error, please di sconnect the AC power cord and wait  for one (1) minute before restarting 
the projector. If the Power or Lamp LEDs are still blinki ng or any other situation that isnt listed in the chart 
above
, please contact your service center. 
Image Problems 
Problem: No image appears on the screen 
1.  Verify the settings on your notebook or desktop PC. 
2.  Turn off all equipment and power up again in the correct order. 
Problem: The image is blurred  
1. Adjust the  Focus on the projector. 
2.  Press the  Auto button on the remote control. 
3.  Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range. 
4.  Check that the projector lens is clean. 
Problem: The image is wider at the top or bottom (trapezoid effect)  
1. Position the projector so it is as perpendicular to the screen as possible.  
2.  Use the  Keystone button on the remote control to correct the problem. 
Problem: The image is reversed  
Check the  Projection setting on the  Installation I menu of the OSD. 
Problem: The image is streaked  
1. Set the  Frequency  and Tracking settings on the  Computer menu of the OSD to the de-
fault settings. 
2.  To ensure the problem is not caused by a connected PC’s video card, connect to another 
computer.  
Problem: The image is flat with no contrast  
Adjust the  Contrast setting on the Image  menu of the OSD. 
Problem: The color of the projected image does not match the source imag\
e. 
Adjust the Color Temperature  and Gamma settings on the  Image menu of the OSD.  
						

							DLP Projector – User’s Manual 
– 47  – 
Lamp Problems 
Problem: There is no light from the projector  
1.  Check that the power cable is securely connected. 
2.  Ensure the power source is good by te sting with another electrical device. 
3.  Restart the projector in the correct order and check that the Power LED is blue. 
4.  If you have replaced the lamp recently,  try resetting the lamp connections.  
5.  Replace the lamp module. 
6.  Put the old lamp back in the projector and have the projector serviced. 
Problem: The lamp goes off 
1. Power surges can cause the lamp to turn  off. Re-plug power cord. When the Power LED 
is on, press the power button. 
2.  Replace the lamp module. 
3.  Put the old lamp back in the projector and have the projector serviced. 
Remote Control Problems 
Problem: The projector does not respond to the remote control  
1. Direct the remote control towards remote sensor on the projector.  
2.  Ensure the path between remote and sensor is not obstructed. 
3.  Turn off any fluorescent lights in the room. 
4.  Check the battery polarity. 
5.  Replace the batteries. 
6.  Turn off other Infrared-enabled devices in the vicinity. 
7.  Have the remote control serviced. 
Audio Problems 
Problem: There is no sound 
1. Adjust the volume on the remote control.  
2.  Adjust the volume of the audio source. 
3.  Check the audio cable connection. 
4.  Test the source audio output with other speakers. 
5.  Have the projector serviced. 
Problem: The sound is distorted  
1. Check the audio cable connection. 
2.  Test the source audio output with other speakers. 
3.  Have the projector serviced. 
Having the Projector Serviced 
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in 
the original carton. Include a description of the problem and a checklist of  the steps you took when 
trying to fix the problem: The information may be usef ul to service personnel. For servicing, return the 
projector to the place you purchased it.  
						

							DLP Projector—User’s Manual 
– 48 – 
HDMITM Q & A 
Q. What is the difference between a “Standard” HDMITM cable and a “High-Speed” 
HDMITM cable? 
Recently, HDMITM Licensing, LLC announced that cables would be tested as Standard or 
High-Speed cables.  
․ Standard (or “category 1”) HDMI
TM cables have been tested to perform at speeds of 75Mhz 
or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.  
․ High Speed (or “category 2”) HDMI
TM cables have been tested to perform at speeds of 
340Mhz or up to 10.2Gbps, which is the highe st bandwidth currently available over an 
HDMI
TM cable and can successfully handle 1080p signals including those at increased color 
depths and/or increased refresh rates from the Source. High-Speed cables are also able to 
accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of 
2560 x 1600). 
 
Q. How do I run HDMITM cables longer than 10 meters? 
There are many HDMITM Adopters working on HDMITM solutions that extend a cable’s effective 
distance from the typical 10 meter range to much longer lengths. These companies 
manufacture a variety of solutions that includ e active cables (active electronics built into 
cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and 
fiber solutions. 
 
Q. How can I tell if a cable is an HDMITM certified cable? 
All HDMITM products are required to be certified  by the manufacturer as part of the HDMITM 
Compliance Test Specification. However, ther e may be instances where cables bearing the 
HDMI
TM logo are available but hav e not been properly tested. HDMITM Licensing, LLC actively 
investigates these instances to ensure that the HDMITM trademark is properly used in the 
market. We recommend that consumers buy  their cables from a reputable source and a 
company that is trusted. 
 
For more detail information check  http://www.hdmi.org/lear
ningcenter/faq.aspx#49 
  
						

							DLP Projector – User’s Manual 
– 49  – 
 
SPECIFICATIONS 
Specifications 
Model  D860 D861 D862 
Display type  TI DMD 0.55” 
Resolution SVGA 800x600 XGA 1024x768 
Projection distance  1 ~ 10 m 
Projection screen size 23” ~ 255” 25.6” ~ 308” 
Projection lens  Manual Focus/Manual Zoom 
Zoom ratio 
1.1x 1.2x 
Vertical keystone correction  +/- 30 steps 
Projection methods Front, Rear, Desktop/Ceiling (Rear, Front) 
Data compatibility VGA, SVGA, XGA, SXGA, SXGA+, UXGA, Mac 
SDTV/EDTV/ HDTV  480i, 480p, 720p, 1080i, 1080p 
Video compatibility NTSC/NTSC 4.43, PAL (B
/G/H/I/M/N/60), SECAM 
H-Sync  15, 30 – 90 kHz 
V-Sync  43 – 120 Hz 
Safety certification FCC-B, cUL, UL, CE, C-tick, CC
C, KC, CB, PCT, NOM, SASO, PSB 
Operation temperature  5° ~ 35°C 
Dimensions 285 mm (W) x 261 mm (D) x 130 mm (H) 
AC Input AC Universal 100-240, Typical @ 110VAC (100-240)/+-10% 
Power consumption  250W 
Stand By 
						

							DLP Projector—User’s Manual 
Projection Distance vs. Projection Size 
 
Projection Distance and Size Table 
D860 / D86ZA～ZE 
IMAGE DIAGONAL 
（INCH） 
IMAGE WIDTH 
(INCH) 
IMAGE HIGHT 
(INCH) 
PROJECTION 
DISTANCE  
（MM）  
FROM 
PROJECTION 
DISTANCE 
 （MM ） 
TO 
OFFSET-A 
( MM ) 
60 48  362353.1  2633.5   128.0 
70 56  422745.2  3072.4   149.4 
72 57.6  43.22823.7  3160.2   153.6 
80 64  483137.4  3511.3   170.7 
84 67.2  50.43294.3  3686.9   179.2 
90 72  543529.6  3950.2   192.0 
96 76.8  57.63764.9  4213.6   204.8 
100 80  603921.8  4389.1   213.4 
120 96  724706.1  5266.9   256.0 
135 108  815294.4  5925.3   288.0 
150 120  905882.6  6583.7   320.0 
200 160  1207843.5  8778.2   426.7 
 
 
 
– 50 –  
						

							DLP Projector – User’s Manual 
– 51  – 
D861 / D86AA～ AE 
IMAGE DIAGONAL 
（INCH） 
IMAGE WIDTH 
(INCH) 
IMAGE HIGHT 
(INCH) 
PROJECTION 
DISTANCE  
（MM）  
FROM 
PROJECTION 
DISTANCE 
 （MM ） 
TO 
OFFSET-A 
( MM ) 
60 48  361950.7  2340.9   128.0 
70 56  422275.8  2731.0   149.4 
72 57.6  43.22340.9  2809.0   153.6 
80 64  482601.0  3121.2   170.7 
84 67.2  50.42731.0  3277.2   179.2 
90 72  542926.1  3511.3   192.0 
96 76.8  57.63121.2  3745.4   204.8 
100 80  603251.2  3901.4   213.4 
120 96  723901.4  4681.7   256.0 
135 108  814389.1  5266.9   288.0 
150 120  904876.8  5852.2   320.0 
200 160  1206502.4  7802.9   426.7 
 
D862 / D86BA～BE 
IMAGE DIAGONAL 
（INCH） 
IMAGE WIDTH 
(INCH) 
IMAGE HIGHT 
(INCH) 
PROJECTION 
DISTANCE  
（MM）  
FROM 
PROJECTION 
DISTANCE 
 （MM ） 
TO 
OFFSET-A 
( MM ) 
60 48 36 1950.72340.9 128.0
70 56 422275.82731.0 149.4
72 57.6 43.2 2340.92809.0 153.6
80 64 482601.03121.2 170.7
84 67.2 50.4 2731.03277.2 179.2
90 72 542926.13511.3 192.0
96 76.8 57.6 3121.23745.4 204.8
100 80 603251.23901.4 213.4
120 96 723901.44681.7 256.0
135 108 814389.15266.9 288.0
150 120 904876.85852.2 320.0
200 160 120 6502.47802.9 426.7 
						

							DLP Projector—User’s Manual 
– 52 – 
 
Timing Mode Table 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC 
(HZ) 
COMPOSITE 
/ S-VIDEOCOMPONENT RGB DVI/ 
HDMITM
NTSC   － 
15.734 60.0 O － － － 
PAL/SECAM  － 
15.625 50.0 O － － － 
720 x 400  37.9 85.0  － 
－ O O 
640 x 480  31.5 60.0  － 
－ O O 
640 x 480  37.9 72.0  － 
－ O O 
640 x 480  37.5 75.0  － 
－ O O 
640 x 480  43.3 85.0  － 
－ O O 
800 x 600  35.2 56.0  － 
－ O O 
800 x 600  37.9 60.0  － 
－ O O 
800 x 600  48.1 72.0  － 
－ O O 
800 x 600  46.9 75.0  － 
－ O O 
800 x 600  53.7 85.0  － 
－ O O 
1024 x 768  48.4 60.0  － 
－ O O 
1024 x 768  56.5 70.0  － 
－ O O 
1024 x 768  60.0 75.0  － 
－ O O 
1024 x 768  68.7 85.0  － 
－ O O 
1280 x 800  49.7 59.8 － － O O 
1280 x 800 
62.8 74.9 － － O O 
1280 x 800 
71.6 84.8 － － O O 
1280 x 1024 
63.98 60.0 － － O O 
1280 x 1024 
79.98 75.0 － － O O 
1280 x 1024 
91.10 85.0 － － O O 
1280 x 960 
60.0 60.0 － － O O 
1280 x 960 
85.9 85.0 － － O O 
1400 x 1050 
65.3 60.0  － 
－ O O 
1440 x 900  70.6 75.0  － 
－ O O 
VESA 
1440 x 900  55.6 60.0  － 
－ 
O O