Vivitek D861 User Manual

DLP Projector—User’s Manual 
Installation II Menu  
Press the MENU button to open the  OSD menu. Press the cursor  ◄► button to move to the  Installa-
tion II  menu. Press the cursor  ▲▼ button to move up and down in the Installation II menu.  
 
ITEM DESCRIPTION 
Auto Source  Press the cursor ◄► button to enable or disable  automatic source detection.  
Auto Power Off 
(min.) Press the cursor ◄►
 button to enable or disable automatic shutdown of lamp when no signal. 
Auto Power On  Press the cursor ◄►...

DLP Projector – User’s Manual 
Advanced Feature 
Press the Menu button to open the OSD menu. Press  ◄► to move to the  Installation II menu. 
Press  ▲▼ to move to the  Advanced menu and then press  Enter or ►. Press  ▲▼ to move up and 
down in the  Advanced menu. Press  ◄► to change values for setting. 
 
ITEM DESCRIPTION 
OSD Menu Setting  Press Enter / 
► to enter the OSD setting menu. See page  36 for more information on  OSD 
Menu
 Setting . 
Peripheral Test  Press Enter/ 
► to enter the Peripheral...

DLP Projector—User’s Manual 
OSD Menu Setting  
 
ITEM DESCRIPTION 
Menu Position Press ◄► button to select different OSD location. 
Translucent Menu  Press ◄► button to select OSD background translucent level.  
Menu Display  Press ◄► button to select OSD timeout delay. 
Peripheral Test 
 
ITEM DESCRIPTION 
Remote Control Test  Press  (Enter) / ► to test the IR remote controller for diagnostic.  
Color Test  Press  (Enter) / ► to select different colors on screen. 
Button Test  Press  (Enter) / ► to...

DLP Projector – User’s Manual 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp  on page 41 to reset the lamp hour counter. 
 
3D 
 
ITEM DESCRIPTION 
3D Press  ◄► to select Off, DLP-Link or IR. 
3D Sync Invert  Press ◄► to turn 3D Sync Invert On or Off. 
– 37  –  

DLP Projector—User’s Manual 
 
Factory Reset 
Press the cursor ▲▼ button to move up and down in the  Installation II menu. Select the  Factory 
Reset  sub menu and press 
 (Enter) /  ► to reset all the menu items to the factory default values 
(expect Language and Security Lock). 
 
Status 
Press the cursor ▲▼  button to move up and down in the  Installation II menu. Select the   
Installation II sub menu and press 
 (Enter) /  ► to enter the  Status sub menu.
 
 
ITEM DESCRIPTION 
Active Source  Display...

DLP Projector – User’s Manual 
– 39  – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
a.  The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product  with general household waste. 
c. Disposal of this product must be carried out in a ccordance with the regulations of...

DLP Projector—User’s Manual 
– 40 – 
2.  Remove the lamp compart-
ment cover. 
 
3.  Remove the three screws 
from the lamp module.  
 
4.   Lift the module handle up. 
5.   Pull firmly on the module  
handle to remove the lamp 
module. 
 
6.   Reverse steps 1 to 5 to install 
the new lamp module.  
While installing, align the 
lamp module with the  
connector and ensure it is 
level to avoid damage. 
Note:  The lamp module must 
sit securely in place and the 
lamp connector must be con-
nected properly...

DLP Projector – User’s Manual 
Resetting the Lamp 
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 
1.  Press the MENU button to open the 
OSD menu. 
2.  Press the cursor  ◄► button to move 
to the  Installation II menu. Press the 
cursor  button to move down to  
Advanced . 
3.  Press the cursor  ▼▲ button to move 
down to  Lamp Hour Reset . 
4.  Press the cursor ► or Enter button.  
A message screen appears. 
5.  Press  ▼▲◄►  buttons to reset the 
lamp...

DLP Projector—User’s Manual 
– 42 – 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Warning: 
1. Be sure to turn off and unplug the projector at  least 30 minutes before cleaning. Failure to do so 
could result in a severe burn. 
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector interior  while cleaning, leave unplugged in a...

DLP Projector – User’s Manual 
Using the Kensington® Lock 
Using the Kensington® Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
For D860/D861 Series 
 
 
 
For D862 Series 
 
 
 
Note: 
Contact your vendor for details on purchasing a suitable Kensi ngton security cable.  
The security lock corresponds to Kensington’s Micr oSaver Security System. If you have any com-
ment, contact: Kensington, 2853 Campus Drive, San...