Vivitek D861 User Manual

DLP Projector—User’s Manual 
For D862 Series 
 
 
ITEM LABEL DESCRIPTION 
A S-VIDEO  Connect the S-VIDEO CABLE from a video device 
B VIDEO IN Connect the COMPOSITE CABLE from a video device  
C HDMITM  Connect the HDMITM CABLE from a HDMITM device 
D HDMITM  Connect the HDMITM CABLE from a HDMITM device 
E  (USB)  Connect the USB CABL
E from a computer 
F VGA IN   Connect the RGB CABLE from a computer 
G RS-232C  Connect the RS-232 serial cable for remote control 
H COMPONENT  Connect the Component...

DLP Projector – User’s Manual 
Starting and Shutting down the Projector 
 
1.  Connect the power cord to the projector. 
Connect the other end to a wall outlet. 
The 
 POWER  LED on the projector 
light. 
2.  Turn on the connected devices.  
3.  Ensure the LAMP LED not a flashing. 
Then press the 
  POWER  button to 
turn on the projector.  
 
The projector splash screen displays and 
connected devices are detected. 
 
See  Setting an Access Password 
(Security Loc
 k) on page  17 if security 
lock is...

DLP Projector—User’s Manual 
4.  If more than one input device is con-
nected, press the SOURCE button and 
use  ▲▼  to scroll among devices. 
(Component is supported through the 
RGB to COMPONENT ADAPTER.) 
 For D860/D861 Series 
 
   VGA: Analog RGB 
Component: DVD 
input YCbCr / 
YPbPr, or HDTV 
input YPbPr  
   Composite Video: Tradi-
tional composite video  For D862 Series 
  VGA: Analog RGB 
   Component: DVD input 
YCbCr / YPbPr. 
   Composite Video: Tra-
ditional composite 
video 
...

DLP Projector – User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See  Navigating the 
OSD  on page  22 and Setting the OSD Language  on page 23 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password,...

DLP Projector—User’s Manual 
5.  You can use the cursor buttons ▲▼◄► 
either on keypad or IR remote control for 
password entry. You can use any 
combination including the same arrow five 
times, but not less than five. 
Press the cursor buttons in any order to set 
the password. Push the  MENU button to 
exit the  dialog box. 
 
 
6.  The password confirm menu appears when 
user presses the power-on key in case the 
Security Lock  is enabled.  
Enter the password in the order you set it 
at step 5. In...

DLP Projector – User’s Manual 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
  The projector table or stand should be level and sturdy. 
   Position the projector so that it is perpendicular to the screen. 
   Ensure the cables are in a safe location. You could trip over them.  
 
To adjust the angle of the picture, turn  the tilt-adjuster right or left until the 
desired angle has been achieved. 
 
–  19  –  

DLP Projector—User’s Manual 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom   
control (on the projector 
only) to resize the pro-
jected image and screen 
size 
B. 
2.  Use the  Image-focus   
control (on the projector 
only) to sharpen the pro-
jected image 
A. 
 
3.  Use the  KEYSTONE  
buttons the remote control 
to correct image-trapezoid 
(wider top or bottom) ef-
fect. For D860/D861 Series 
  For D862 Series 
Volume
+-
4.  The keystone control  
appears on the display. 
– 20 –
  

DLP Projector – User’s Manual 
Adjusting the Volume 
For D860/D861 Series 
 For D862 Series 
Volume
+-
1.  Press the 
Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
2.  Press the  MUTE button to 
turn off the volume (This 
feature is available only on 
the  D862 Series  remote). 
 
 
– 21  –  

DLP Projector—User’s Manual 
– 22 – 
 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you ma ke image adjustments and change various settings.  
Navigating the OSD 
You can use the remote contro l cursor buttons to navigate and make changes to the OSD.  
                              
            
1.  To enter the OSD, press the 
MENU  button.  
2.  There are five menus. Press  the cursor  ◄► button to 
move through the menus.  
3. Press the cursor  ▲▼...

DLP Projector – User’s Manual 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1.  Press the  MENU button. Press the cursor  ◄► button to navigate to Installation I. 
 
2.  Press the cursor  ▲▼ button until  Language is highlighted.  
 
3.  Press the cursor  ◄► button until the language you want is highlighted.  
4.   Press the  MENU button twice to close the OSD.   
– 23  –