Vivitek D860 User Manual

							DLP Projector—User’s Manual 
 Rear view 
For D860/D861 Series 
 
 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  AC IN  Connect the POWER CABLE 15 
2.  AUDIO IN  Connect an AUDIO CABLE from the input device 
3.  VGA IN  Connect the RGB CABLE from  a computer and components 
4.  VGA OUT Connect the RGB CABLE to a display 
5.  VIDEO IN  Connect the COMPOSITE CABLE from a video device  
6.  RS-232C  Connect RS-232 serial port cable for remote control 
13 
7.  Kensington Lock Secure to permanent object with a Kensington® Lock system 43 
 
– 4 –  
						

							DLP Projector – User’s Manual 
For D862 Series 
 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  AC IN Connect the POWER CABLE 15 
2.  S-VIDEO   Connect the S-VIDEO CABLE from a video device 
3.  VIDEO IN Connect the COMPOSITE CABLE from a video device  
4.  HDMITM  Connect the HDMITM CABLE from a HDMITM device 
5.  HDMITM  Connect the HDMITM CABLE from a HDMITM device 
6.    (USB)  Connect the USB CABLE from a computer  
7.  VGA IN  Connect the RGB CABLE from a computer 
8.  RS-232C  Connect RS-232 serial port cable for remote control 
9.  COMPONENT  Connect the Component CABLE to a display 
13 
10.  Kensington Lock Secure to permanent object with a Kensington® Lock system 43 
11.  AUDIO IN (L and R) Connect the AUDIO CABLES from a audio device 
12.  AUDIO IN  Connect an AUDIO CABLE from the input device 
13.  AUDIO OUT Connect an AUDIO CABLE for audio loop through 
13 
 
– 5 –   
						

							DLP Projector—User’s Manual 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 
2.  Tilt adjustor  Rotate adjuster lever to adjust angle position.  19 
 
Note: 
When installing, ensure that you us e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of 12 mm (0.47 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount 
load capacity must exceed the  weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight  of the equipment (not less than 5.15 kg) over a 
period of 60 seconds. 
 
– 6 –  
						

							DLP Projector – User’s Manual 
Remote Control Parts  
For D860/D861 Series 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Up cursor Navigates and changes settings in the OSD   
2.  Enter  Changes settings in the OSD 
22 
3.  Power Turns the projector On or Off 15 
4.  Right cursor  Navigates and changes settings in the OSD 22 
5.  Volume + Increase volume 
6.  Volume - Decrease volume 
21 
7.  Blank  Video off and audio mute 
8.  Freeze Freeze/unfreezes the on-screen picture 
9.  Source Detects the input device 13 
10.  Auto Auto adjustment for frequency, tracking, size, position (RGB only) 
11.  Keystone top  Corrects image-trapezoid (wider top) effect 
12.  Keystone bottom  Corrects image trapezoid (wider bottom) effect 
20 
13.  Down cursor Navigates and changes settings in the OSD 
14.  Left cursor Navigates and changes settings in the OSD 
15.  Menu Opens the OSD  
22 
– 7 –   
						

							DLP Projector—User’s Manual 
Inserting the Remote Control Batteries 
 
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow (A). Pull out the cover (B). 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution:  
1. Only use a 3V lithium battery (CR2025). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods. 
– 8 –  
						

							DLP Projector – User’s Manual 
For D862 Series 
 
  
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter Transmits signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up Up arrow when connected through USB to a PC 
5.  Right  Right arrow when connected through USB to a PC 
6.  Down  Down arrow when connected through USB to a PC 
7.  Page Down  Page down when connected through USB to a PC 
8.  Up cursor  
9.  Right cursor  
10.  Down cursor  Navigates and changes settings in the OSD
  
22 
–  9 –   
						

							DLP Projector—User’s Manual 
– 10 – 
ITEM LABEL DESCRIPTION SEE PAGE: 
11.  Volume +/-  Adjusts volume 21 
12.  Mute  Mutes the built-in speaker 
13.  Zoom+  Zoom in  
14.  Zoom- Zoom  out 
15.  Freeze  Freeze/unfreezes the on-screen picture 
16.  Blank Makes the screen blank 
17.  Source Detects the input device 
18.  Auto Auto adjustment for phase, tracking, size, position 
19.  Menu  Opens the OSD  22 
20.  Status  Opens the OSD Status menu (the menu only opens when an 
input device is detected) 38 
21.  Keystone top/bottom  Corrects image-trapezoid (wider top/bottom) effect 20 
22.  Left cursor Navigates and changes settings in the OSD   
23.  Enter Changes settings in the OSD 
24.  Page Up Page up when connected through USB to a PC 
25.  Left  Left arrow when connected through USB to a PC 
26.  Enter  Enter key when connected through USB to a PC 
22 
27.  Power  Turns the projector on or off 15 
28.  Laser  Use as on-screen pointer.  DO NOT POINT IN EYES .  
						

							DLP Projector – User’s Manual 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods. 
– 11  –  
						

							DLP Projector—User’s Manual 
– 12 – 
 
Important: 
1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the re mote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have the  same functions as the corresponding buttons on 
the remote control. This user’s manual descri bes the functions based on the remote control. 
 
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using t he remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote cont rol; however, the buttons on the projector are lim-
ited in use.  
 
  
						

							DLP Projector – User’s Manual 
 
SETUP AND OPERATION 
Connecting Input Devices 
A PC or notebook computer and video devices can be connected to the projector at the same time. Video 
devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. 
Check the user manual of the connecting device to  confirm it has the appropriate output connector.  
 
Warning: 
As a safety precaution, disconnect all power to  the projector and connecting devices before making 
connections. 
 
 
 
For D860/D861 Series 
 
 
 
ITEM LABEL DESCRIPTION 
A AUDIO IN  Connect an AUDIO CABLE from the input device 
B VGA IN  Connect the RGB CABLE from a computer or components 
C VGA OUT Connect the RGB CABLE to a display 
D VIDEO IN  Connect the COMPOSITE CABLE from a video device  
E RS-232C  Connect RS-232 serial port cable for remote control 
– 13  –