Vivitek D858wtpb User Manual

 
 
  Preface 
5.  When the “Power Off? /Press Power
 
again” message appears, press the 
POWER  button. The projector turns 
off. 
 
Caution: 
1. Be sure to remove the lens  cap before starting projector.  
2. Do not unplug the power cord until the POWER LED stops flashing–indicating the projector has 
cooled down. 
 
 
 
– 11  –  

DLP Projector—User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See  Navigating the 
OSD  on page  17 and Setting the OSD Language  on page 18 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password,...

 
 
  Preface 
5.  You can use the cursor buttons 
▲▼◄► 
either on keypad or IR remote control for 
password entry. You can use any 
combination including the same arrow five 
times, but not less than five. 
Press the cursor buttons in any order to set 
the password. Push the  MENU button to 
exit the  dialog box. 
 
 
6.  The password confirm menu appears when 
user presses the power-on key in case the 
Security Lock  is enabled.  
Enter the password in the order you set it 
at step 5. In case you...

DLP Projector—User’s Manual 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
•  The projector table or stand should be level and sturdy. 
•   Position the projector so that it is perpendicular to the screen. 
•   Ensure the cables are in a safe location. You could trip over them.  
A
D
C 
1.  To raise the level of the projector, lift the projector  [A] and press the height-adjuster 
button  [B].  
The height adjuster drops down  [C].  
2.  To lower the level of...

 
 
  Preface 
Adjusting Focus and Keystone 
1.  Use the 
Image-focus   
control (on the projector 
only) to adjust the pro-
jected image. 
 
2.  Use the  KEYSTONE  
buttons (on the projector 
or the remote control) to 
correct image-trapezoid 
(wider top or bottom)  
effect. 
 
Remote control and OSD panel
3.  The keystone control  
appears on the display. 
–  15  –  

DLP Projector—User’s Manual 
Adjusting the Volume 
1.  Press the Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
2.  Press the  Left or Right 
Cursor  buttons on the 
keypad to adjust  Volume 
+/-.  
 
 
MENU
SOURCEAUTO
 
3.  Press the  MUTE button to 
turn off the volume (This 
feature is available only 
on the remote). 
 
—  16 —  

 
 
  Preface 
–
 17  – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you ma ke image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control curs or buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illu stration shows the corresponding buttons on the 
projector. 
MENU
SOURCEAUTO
                            
1
2
3 4
5
 
1.  To enter the OSD, press the 
MENU...

DLP Projector—User’s Manual 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1.  Press the  MENU button. Press the cursor  ◄► button to navigate to Installation I. 
 
2.  Press the cursor  ▲▼ button until  Language is highlighted.  
 
3.  Press the cursor  ◄► button until the language you want is highlighted.  
4.   Press the  MENU button twice to close the OSD.   
— 18 —  

 
 
  Preface 
OSD Menu Overview 
Use the following illustration to quickly find a se
tting or determine the range for a setting. 
English, French, German, Spanish, Portuguese, Simplified Chinese, Traditional 
Chinese, Italian, Norwegian, Swedish, Dutch, Russian, Polish, Finnish, Greek, 
Korean, Hungarian, Czech, Arabic, Turkis h, Vietnamese, Japanese, Thai, Farsi
 
 
–  19  –  

DLP Projector—User’s Manual 
OSD Sub-Menu Overview 
 
— 20 —