Vivitek D803w 3d Projector User Manual

							 
 
  DLP Projector—User’s Manual 
Top view—On-screen Display (OSD) buttons and LEDs 
1
2
3
4
5 9 6
7
8
1
0
11
12 
ITEM LABEL DESCRIPTION SEE 
PAGE: 
1.  MENU 
Opens and exits OSD menus 16 
2.  ▲ (Up cursor) /  
Keystone+  Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
3.  SOURCE 
Enter the Source menu 
4.  ◄ (Left cursor) /  
Volume-  Navigates and changes settings in the OSD 
Quick Menu – For Volume 
16 
5.  Enter 
Enter or confirm highlighted OSD menu item 
6.  AUTO Optimizes image size, position, and resolution 
7.  ► (Right cursor) /  
Volume+  Navigates and changes settings in the OSD 
Quick Menu – For Volume 
8.  ▼
 (Down cursor) / 
Keystone-  Navigates and changes settings in the OSD 
Quick Menu – For Keystone 16 
9.   (Power button) 
Turns the projector On or Off. 
Solid Red 
Lamp Error. 10.  LAMP LED 
Flashing Red Lamp temperature too high 
Solid Green  Power On  11.  POWER LED 
Flashing Green System Initialized / Cooling / Error code 
12.  TEMP LED  Solid Red Over temperature 
40 
 
– 3 –   
						

							DLP Projector—User’s Manual 
 Rear view 
Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before making 
connections. 
 
12369
12
47
10
13
5
8
11 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  AC IN 
Connect the POWER cable 10 
2.  S-VIDEO   Connect the S-VIDEO cable from a video device 
3.  VIDEO IN 
Connect the COMPOSITE cable from a video device  
4.  HDMI 1 Connect the HDMI cable from a HDMI device 
5.  HDMI 2 Connect the HDMI cable from a HDMI device 
6.    (USB) Connect the USB cable from a computer  
7.  VGA IN   Connect the RGB cable from a computer 
8.  RS-232C Connect RS-232 serial port cable for remote control 
9.  COMPONENT  Connect the Component cable from a component device 
10.  Kensington Lock Secure to permanent object with a Kensington® Lock system 38 
11.  AUDIO IN (L and R) Connect the AUDIO cable from a audio device 
12.  AUDIO IN  Connect an AUDIO cable from the audio device 
13.  AUDIO OUT  Connect an AUDIO cable to audio amplifier 
 
 
— 4 —  
						

							 
 
  DLP Projector—User’s Manual 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Ceiling support holes 
Contact your dealer for information on mounting the projector on a ceiling 
2.  Tilt adjustor  Rotate adjuster lever to adjust angle position.  14 
 
Note: 
When installing, ensure that you us e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of 12 mm (0.47 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount 
load capacity must exceed the  weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight  of the equipment (not less than 5.15 kg) over a 
period of 60 seconds. 
 
– 5 –   
						

							DLP Projector—User’s Manual 
Remote Control Parts  
 
  
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter Transmits signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up Up arrow when connected through USB to a PC 
5.  Right  Right arrow when connected through USB to a PC 
6.  Down  Down arrow when connected through USB to a PC 
7.  Page Down  Page down when connected through USB to a PC 
8.  Up cursor  
9.  Right cursor  
10.  Down cursor  Navigates and changes settings in the OSD
  
16 
11.  Volume +/-  Adjusts volume 15 
— 6 —  
						

							 
 
  DLP Projector—User’s Manual 
–
 7 –  
ITEM LABEL DESCRIPTION SEE PAGE: 
12.  Mute  Mutes the built-in speaker 
13.  Zoom+  Zoom in  
14.  Zoom- Zoom  out 
15.  Freeze  Freeze/unfreezes the on-screen picture 
16.  Blank Makes the screen blank 
17.  Source Detects the input device 
18.  Auto Auto adjustment for phase, tracking, size, position 
19.  Menu  Opens the OSD  16 
20.  Status  Opens the OSD Status menu (the menu only opens when an 
input device is detected) 33 
21.  Keystone top/bottom 
Corrects image-trapezoid (wider top/bottom) effect 15 
22.  Left cursor Navigates and changes settings in the OSD   
23.  Enter Changes settings in the OSD 
24.  Page Up Page up when connected through USB to a PC 
25.  Left  Left arrow when connected through USB to a PC 
26.  Enter  Enter key when connected through USB to a PC 
16 
27.  Power  Turns the projector on or off 10 
28.  Laser  Use as on-screen pointer.  DO NOT POINT IN EYES . 
  
						

							DLP Projector—User’s Manual 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods. 
 
 
 
 
 
— 8 —  
						

							 
 
  DLP Projector—User’s Manual 
–
 9 –  
Important: 
1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the re mote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have the  same functions as the corresponding buttons on 
the remote control. This user’s manual descri bes the functions based on the remote control. 
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using t he remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote cont rol; however, the buttons on the projector are lim-
ited in use.  
 
  
						

							DLP Projector—User’s Manual 
— 10 — 
SETUP AND OPERATION 
Starting and Shutting  down the Projector 
 
1.  Connect the power cord to the projector. 
Connect the other end to a wall outlet. 
The 
 POWER  LED on the projector 
light. 
2.  Turn on the connected devices.  
3.  Ensure the POWER LED not a flashing. 
Then press the 
  POWER  button to 
turn on the projector.  
 
The projector splash screen displays and 
connected devices are detected. 
 
See  Setting an Access Password 
(Security Lock)  on page 12 if security 
lock is enabled. 
4.  If more than one input device is con-
nected, press the SOURCE  button and 
use  ▲▼  to scroll among devices. 
 
 
•   VGA: Analog RGB 
•   Component: DVD input YCbCr / YPbPr, or HDTV input 
YPbPr. 
•   Composite Video: Traditional composite video 
•   S-Video: Super video (Y/C separated)  
•   HDMI 1/HDMI 2: High-Definition Multimedia Interface   
						

							 
 
  DLP Projector—User’s Manual 
5.  When the “Power Off? /Press Power
 
again” message appears, press the 
POWER  button. The projector turns 
off. 
 
Caution: 
1. Be sure to remove the lens  cap before starting projector.  
2. Do not unplug the power cord until the POWER LED stops flashing–indicating the projector has 
cooled down. 
 
 
– 11  –  
						

							DLP Projector—User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See  Navigating the 
OSD  on page  16 and Setting the OSD Language  on page 17 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password, contact your reselle r for information on clearing the password. 
 
1.  Press the MENU button to open the OSD 
menu. 
2.  Press the cursor  ◄► button to move to 
the  Installation I  menu, press the cursor 
▲▼  button to select  Advanced. 
3.  Press the cursor  ▲▼ button to select  
Security Lock . 
4.  Press the cursor  ◄► button to enable or 
disable security lock function. 
A password dialog box automatically  
appears. 
—  12 —