Vivitek D5380u User Manual

							DLP Projector—User’s Manual 
— 52 — 
MAINTENANCE AND SECURITY 
Tilt Up/Down caution 
¾  When projector detect angle is over spec, popup caution message. 
 
The model with Standard lamp module 
The model with Standard lamp module can be used projection angle as shown below. 
If Projector projection angle exceeds the drawing show n and don’t use tilt lamp module. Showing caution 
message for 5sec and then disappear, projector remain on. (every time when projector on 
 ; This function 
can be disable see 
Advanced 1 Feature on page 38 ) 
1515
Standard Lamp 
The model with Tilt lamp module 
The model with Tilt lamp module can be used projection angle as shown below. 
If Projector projection angle exceeds the drawing sh own and don’t use standard lamp module. Showing 
caution message for 5sec and then disappear, projector remain on. (every time when projector on 
 ; This 
function can be disable see 
Advanced 1 Feature on page  38 ) 
Tilt Lamp
1515
 
Warning: 
Your operation might cause lamp defect and life decay. If used incorrect lamp module 
  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
 
 
 
 
Standard lamp module  Tilt lamp module 
 ( Optional ) 
Note: 
The standard lamp is to go with regular shipment for normal operation and the tilt lamp is an 
option lamp for abnormal operation 
– 53  –  
						

							DLP Projector—User’s Manual 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be replaced with a 
certified replacement part, which you can order from your local dealer.  
Important: 
a.  The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product  with general household waste. 
c. Disposal of this product must be carried out in  accordance with the regulations of your local  
authority. 
Warning: 
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. 
Failure to do so could result in a severe burn. 
 
Caution: 
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or 
shards to be discharged outward from the rear exhaust vent. 
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.  
Always keep your face away from the exhaust ve nt so that you do not suffer from the gas and 
broken shards of the lamp. 
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the 
projector. Glass fragments could fall if the lamp has been burned out.  
！ IF A LAMP EXPLODES 
If a lamp explodes, the gas and broken shards may scatter inside the projector and they may 
come out of the exhaust vent. T he gas contains toxic mercury. 
Open windows and doors for ventilation. 
If you inhale the gas or the shards  of the broken lamp enter your eyes or mouth, consult the 
doctor immediately.  
 
1.  Switch off the power to the 
projector by pressing the 
POWER button. 
2.  Allow the projector to cool 
down at least 30 minutes. 
3.  Disconnect the power 
cord. 
— 54 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
4.  Unlock the lamp cover. 
5.  Pull up and remove the 
cover. 
 
6.  Use a screwdriver to 
remove the screws from 
the lamp module. 
 
7.  Pull out the lamp module. 
 
–  55  –  
						

							DLP Projector—User’s Manual 
8.  Reverse steps 1 to 7 to 
install the new lamp 
module.  
While installing, align the 
lamp module with the 
connector and ensure it is 
level to avoid damage. 
Note:  
The lamp module must sit 
securely in place and the 
lamp connector must be 
connected properly before 
tightening the screws.  
 
 
— 56 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Resetting the Lamp 
After replacing the lamp, you should reset the lamp  hour counter to zero. Refer to the following: 
1.  Press the MENU button to open 
the OSD menu. 
2.  Press the cursor  ◄► button to 
move to the  Settings 2 menu. 
Press the cursor button to move 
down to Advanced 1 and press 
enter. 
3.  Press the cursor  ▼▲ button to 
move down to  Lamp Hour Reset .
4.  Press the cursor ► or Enter 
button.  
A message screen appears. 
5.  Press  ▼▲◄►  buttons to reset 
the lamp hour. 
6.  Press the  MENU button to get 
back to  Settings 2. 
– 57  –  
						

							DLP Projector—User’s Manual 
Cleaning the filter (filter: optional parts) 
The air filter prevents dust from accumulating on the surface of the optical elements inside the 
projector. If the filter is dirty or clogged, your  projector may overheat or degrading the projected 
image quality. 
1.  Turn off the projector, and 
unplug the AC power cord 
from the AC outlet.
 
2.  Cleaning the filter with a 
vacuum cleaner.
 
 
 
Caution: 
Recommend avoiding dusty or smoky environmen ts when you operate the projector, it may 
cause poor image quality. 
If the filter is heavily clogged and unabl e to clean, replace a new filter. 
 
Note:  
Using a ladder is recommended to access the filter. Do not remove the projector from the 
wall mount. 
— 58 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Replacing the Filter 
1.  Turn off the projector, and 
unplug the AC power cord 
from the AC outlet.  
Clean up the dust on the 
projector and around the 
air vents.  
Pull out the filter cover and 
remove from the projector 
 
2.  Lift the filter from the filter 
cover. 
 
 
3.  Replace a new filter 
module or replace filter into 
cover. 
 
4.  Replace the filter cover 
back to the projector by 
pushing gently in the  
direction shown. 
 
Warning: 
Do not wash the filter with the water or other liquid matter 
 
Important: 
When the lamp is replaced, the filter should also be replaced, not cleaned. 
–  59  –  
						

							DLP Projector—User’s Manual 
— 60 — 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Warning: 
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do 
so could result in a severe burn. 
2. Use only a dampened cloth when cleaning. Do  not allow water to enter the ventilation 
openings on the projector.  
3. If a little water gets into the projector inte rior while cleaning, leave unplugged in a well-
ventilated room for several hours before using. 
4. If a lot of water gets into the projector inte rior when cleaning, have the projector serviced. 
Cleaning the Lens 
You can purchase optic lens cleaner from most camera stores . Refer to the following to clean the 
projector lens. 
1.  Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly 
to the lens.) 
2.  Lightly wipe the lens in a circular motion. 
Caution: 
1.  Do not use abrasive cleaners or solvents. 
2. To prevent discoloration  or fading, avoid getting cleaner on the projector case. 
Cleaning the Case 
Refer to the following to clean the projector case. 
1.  Wipe off dust with a clean dampened cloth. 
2.  Moisten the cloth with warm water and mild detergent (such as used to wash dishes), 
and then wipe the case. 
3.  Rinse all detergent from the cloth and wipe the projector again. 
Caution: 
To prevent discoloration or fading of the case, do not use abrasive  alcohol-based cleaners.  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Using the Physical Lock 
Using the Kensington® Lock 
If you are concerned about security, attach t he projector to a permanent object with the 
Kensington slot and a security cable.  
 
Note: 
Contact your vendor for details on purchasing a suitable Kensi ngton security cable.  
The security lock corresponds to Kensington’s Mi croSaver Security System. If you have any 
comment, contact: Kensington, 2853 Campus Drive, San Mateo,  CA 94403, U.S.A. Tel: 800-
535-4242, http://www.Kensington.com. 
Using the Security Chain Lock 
In addition to the password protection function  and the Kensington lock, the Security Chain 
Opening helps protect the PROJ ECTOR from unauthorized use. 
See the following picture. 
 
–  61  –