Vivitek D5190hd User Manual

							DLP Projector—User’s Manual 
Installing the New Lens 
1.  Align the notches and correctly 
position the electrical contact pad as 
shown in the picture. 
Note: 
Pin of Electrical contact pins should 
be in the direction as shown in the 
picture. 
2.  Rotate the lens clockwise until you 
feel it click into place. 
Electrical contact pins
 
— 12 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Starting and Shutting  down the Projector 
1.  Remove the lens cap. 
 
2.  Securely connect the power cord 
and signal cable. When connected, 
the power led will turn red. 
 
3.  Turn on the lamp by pressing 
“
” button on the rear of the 
projector or “
” on the remote 
control. 
The PWR LED will now flash red.  
The startup screen will display in 
approximately 30 seconds. The first 
time you use the projector, you can 
select your preferred language from 
quick menu after the startup screen 
display. 
–  13  –  
						

							DLP Projector—User’s Manual 
4.  If more than one input device is 
connected, press the SOURCE 
button and use ▲▼  to scroll among 
devices. 
 
•  DVI: Digital Visual Interface 
•   HDMI: High-Definition Multimedia Interface 
compatible 
•   DisplayPort: Digital display interface 
•   VGA 1 / 2: Analog RGB 1 / 2 
•   BNC: Analog RGB (BNC connector) 
•  
Component Video: DVD input YCbCr / YPbPr , or 
HDTV input YPbPr
  
•   S-Video: Super video (Y/C separated)  
• Composite Video: Traditional composite video 
5.  When the “Power Off? /Press 
Power  again” message appears, 
press the POWER  button. The 
projector turns off. 
 
Caution: 
1. Be sure to remove the lens  cap before starting projector.  
2. Do not unplug the power cord until the READ Y LED stops flashing–indicating the projector 
has cooled down. 
— 14 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to se t a password and prevent unauthorized use of the 
projector. When enabled, the password must be entered after you power on the projector. (See 
Navigating the OSD  on page 24 and Setting the OSD Language  on page 25 for help on using 
OSD menus.) 
Important: 
Keep the password in a safe pl ace. Without the password, you will not be able to use the 
projector. If you lose the password, contact  your reseller for information on clearing the 
password. 
 
1.  Press the MENU button to open the 
OSD menu. 
2.  Press the cursor  ◄► button to move to 
the Settings 1 menu, press the cursor 
▲▼  button to select  Advanced 1. 
3.  Press  (Enter) / ► to enter the 
Advanced 1 sub menu. Press the 
cursor ▲▼  button to select  Security 
Lock. 
4.  Press the cursor  ◄► button to enter 
and enable or disable security lock 
function. 
A password dialog box automatically 
appears. 
–  15  –  
						

							DLP Projector—User’s Manual 
5.  You can use the cursor buttons 
▲▼◄► 
either on keypad or IR remote control 
for password entry. You can use any 
combination including the same arrow 
five times, but not less than five. 
Press the cursor buttons in any order to 
set the password. Push the  MENU 
button  to exit the  dialog box. 
6.  The password confirm menu appears 
when user presses the power-on key in 
case the Security Lock  is enabled.  
Enter the password in the order you set 
it at step 5. In case you forget the 
password, please contact the service 
center.  
The service center will validate the 
owner and help reset the password.  
 
 
—  16 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
•   The projector table or stand should be level and sturdy. 
•   Position the projector so that it is perpendicular to the screen. 
•   Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection  
angle. 
•   Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, 
twist the adjusters counter 
clockwise. 
2.  To lower the level of the projector, 
lift the projector and twist the 
adjusters clockwise. 
 
 
– 17  –  
						

							DLP Projector—User’s Manual 
Adjusting Projected Image Position Using Shift 
 
Note: 
Suggest to loosen the screw before lens 
shift  adjustment and tighten up after 
finished adjustment. 
The Shift feature provides a lens shift functi on that can be used to adjust the position of the 
projected image either horiz ontally or vertically within the range detailed below. 
Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast 
ratio than traditional lens shift systems. 
Adjusting the vertical image position 
The vertical image height can  be adjusted between 110% and -30%  ( WUXGA,  WXGA), 100% 
and -20% (XGA), 120% and -40% ( 10 80P) of offset position. Note that the maximum vertical 
image height adjustment can be limit ed by the horizontal image position. For example it is not 
possible to achieve the maximum vertical image position height detailed abo ve if the horizontal 
image position is at maximum.  Please consult the Shift Range diagram below for further 
clarification. 
WUXGA and WXGA 
Screen
Distance(L)
(H/2) x 10% 100%
Screen Height
(H)
+110%-30%
0%
W
UXGA / WXGA 30% x (H/2)
110% x (H/2) 
—  18 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
XGA 
Screen
Distance(L)
100%
Screen 
Height
(H)
-20%
+100%
X
GA
100% x (H/2)
 
 
1080P 
Screen
Distance(L)
(H/2) x 20% 100%
Screen Height
(H)
+120%-40%
0%
1
080P 40% x (H/2)
120% x (H/2
)
 
–
 19  –  
						

							DLP Projector—User’s Manual 
Adjusting the horizontal image position 
With the lens in the center position the horizontal image position can be adjusted to the left or right 
by up to a maximum of 10% of the half image wi dth. Note that the maximum horizontal image 
height adjustment can be limited by the vertical image position. For example it is not possible to 
achieve the maximum horizontal image position if the vertical  image position is at maximum. 
Please consult the Shift Range diagram  below for further clarification. 
 
Shift Range Diagram 
WUXGA and WXGA 
The max H up shift = H/2 x 110% 
The max H down shift = H/2 x 30% 
The max W shift = W/2 x 10% 
When max W shift is W/2 x 10%  
max H shift = H/2 x 100% 
When max H shift is H/2 x 110%   max W shift = H x 0% 
 
— 20 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
XGA 
The max H up shift = H/2 x 100% 
The max H down shift = H/2 x 20% 
The max W shift = W/2 x 10% 
When max W shift is W/2 x 10%  
max H shift = H/2 x 90% 
When max H shift is H/2 x 100%   max W shift = H x 0% 
 
1080P 
The max H up shift = H/2 x 120%  
The max H down shift = H/2 x 20%  
The max W shift = W/2 x 10%  
When max W shift is W/2 x 10%  max H shift = H/2 x 110%  
When max H shift is H/2 x 120%  max W shift = H x 0% 
 
–  21  –