Vivitek D5190hd User Manual

							DLP Projector—User’s Manual 
Views of Projector Parts  
Front-right View 
2345678101119 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Screw 
For ensure the lens position 
2.  Vertical lens shift Adjusts the image position vertically 18 
3.  Lens release button  Press the release button before removing the 
lens 11 
4.  Horizontal lens shift 
Adjusts the image position horizontally 20 
5.  IR receiver Receives IR signal from remote control 7 
6.  Lens Projection  Lens 
7.  Focus ring Focuses the projected image 
8.  Zoom ring Enlarges the projected image 
22 
9.  Height adjuster  Adjusts level of projector 17 
10.  Function keys See Top view—On-screen Display (OSD) 
buttons and LEDs. 3 
11.  Lamp cover 
Removes cover to replace lamp module 52 
Important: 
Ventilation openings on the projecto r allow for good air circulation, which keeps the projector 
lamp cool. Do not obstruct any  of the ventilation openings. 
 
Note: 
Suggest to loosen the screw before lens shift adjustment and tighten up after finished 
adjustment. 
— 2 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
 
Top view—On-screen Displa y (OSD) buttons and LEDs 
 
ITEM LABEL DESCRIPTION SEE 
PAGE: 
1.  MENU Opens and exits OSD menus 
2.   Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
3.  ENTER 
Enter or confirm highlighted OSD menu item 
24 
4.  BLANK  Displays a blank screen and mutes audio 
5.   Navigates and changes settings in the OSD 
Quick Menu – For Volume - 24 
6.  AUTO 
Optimizes image size, position, and resolution 
7.   Navigates and changes settings in the OSD 
Quick Menu – For Volume + 
8.    
Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
24 
9.  SOURCE 
Enter the Source menu 
– 3 –   
						

							DLP Projector—User’s Manual 
Rear view 
1234
56789 10 1112
1314
1516
17
18
19
20
21
22
2
324
252627
28
293031 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  VGA1  Connect a RGB cable from a computer or a video enabled device. 
2.  AUDIO IN 1 Connect the AUDIO cable from an input device. 
3.  VGA2  Connect a RGB cable from a computer or a video enabled device. 
4.  AUDIO IN 2  Connect the AUDIO cable from an input device. 
Note: Share with DVI & BNC audio input. 
5.  POWER Turns the projector on or off (main power switch must 
be turned on first). Press to place the projector in 
standby mode. 13 
Red 
Standby, Over Temperature 
Blue  Lamp Lit , System stable 6.  PWR LED 
Flashing Power on, Cooling, Error code (See as 
LED indicator table) 
7.  TEMP LED 
Red Over temperature 
Red Lamp Lit , System stable, Lamp Fail 8.  READY LED 
Flashing Error code (See as LED indicator table) 
63 
9.  HDMI  Connect the HDMI cable from a HDMI device. 
10.  DVI-D Connect the DVI cable from a computer. 
11.  3D SYNC OUT 
(5V)  Connect 3D IR glas
ses receiver unit. 
12.  DISPLAYPORT  Connect a DISPLAYPORT  cable to a DISPLAYPORT source. 
13.  USB CHARGE 
(1.5A) For USB charge. 
14.  RJ-45 
Connect a LAN cable from Ethernet. 
— 4 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
–  5 –  
ITEM LABEL DESCRIPTION SEE PAGE: 
15.  VGA OUT  Connect the RGB cable to a display. 
 (Pass through by VGA1 only) 
16.  AUDIO OUT 
Connect an AUDIO cable for audio loop through. 
17.  BNC Connect a BNC cable from a computer. 
18.  IR receiver Receive IR signal from remote control. 7 
19.  SERVICE  For service use. 
20.  RS-232 Connects RS-232 serial port cable for remote control. 
21.  12V  When connected to the screen through 
a commercially available cable, 
the screen deploys automatically on st art up of the projector. The screen 
retracts when the projector is powered off (see notes below). 
22.  WIRED REMOTE  Wire remote control connector (connect
 with wire remote connector of the 
Remote Control set). 
23.  AUDIO IN 3 L/R 
RCA (YPbPr)  Connect the audio cables from a audio device. 
24.  
AUDIO IN 4 L/R 
RCA (Video/ S-
Video) Connect the audio cables from a audio device. 
25.  VIDEO 
Connect the composite cable from a video device. 
26.  S-VIDEO Connect the S-video cable from a video device. 
27.  YPbPr  Connect a component video enabled device. 
28.  AC IN Connects the power cable. 
29.  Power switch  Turns on/off the projector. 
13 
30.  Security chain 
lock Helps protect the projector from unauthorized use. 
31.  Kensington Lock 
Secures to permanent object with a Kensington® Lock 
system. 
61 
 
 
 
 
 
 
 
Note: 
y 
To use this feature, you must plug in t he connector before turn on/off the projector. 
y Screen controllers are supplied and  supported by screen manufacturers. 
y Do not use this jack for any thing other than intended use. 
 
Note: 
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the  
S-VIDEO connector. S-VIDEO provides a better quality signal. 
 
Warning: 
As a safety precaution, disconnect all power  to the projector and connecting devices before 
making connections. 
  
						

							DLP Projector—User’s Manual 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Tilt adjustor  Rotate adjuster lever to adjust angle position.  17 
2.  Ceiling support holes  Contact your dealer for information on mounting the projector on a 
ceiling 
 
Note: 
When installing, ensure that you us
e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounti ng hardware and M4 screws with a maximum 
screw depth of 6 mm (0.23 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling 
mount load capacity must exceed the weight of  the installed equipment, and as an additional 
precaution be capable of withstanding three times the weight of the equipment (not less than 
5.15 kg) over a period of 60 seconds. 
— 6 —  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Remote Control Parts 
 
 
Important: 
1.  Avoid using the projector with bright fluore scent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the  remote control and the projector. If the path 
between the remote control and the projector is obstructed,  you can bounce the signal off 
certain reflective surfaces  such as projector screens. 
 
3. The buttons and keys on the projector have the  same functions as the corresponding buttons 
on the remote control. This user’s manual descr ibes the functions based on the remote control. 
– 7 –   
						

							DLP Projector—User’s Manual 
— 8 — 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Power OFF  Turns the projector off 13 
2.  DVI  Displays the DVI source selection 
3.  VGA Displays the VGA source selection 
4.  DP Displays the DisplayPort source selection 
5.  Up cursor /  
Keystone+ Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
6.  ENTER 
Enters and confirms settings in the OSD 
7.  Right cursor  Navigates and changes settings in the OSD 
8.  Down cursor /  
Keystone- Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
24 
9.  3D 
Activate 3D video (not available in D5180HD series) 
10.  PICTURE MODE  Changes the Display Mode setting 
11.  SOURCE Alternate input source 24 
12.  CONTRAST Displays the contrast settings bar 
13.  BRIGHT  Displays the brightness setting bar  
14.  SHARP Displays the sharpness setting bar  
15.  COLOR Displays the color setting bar 
16.  FREEZE  Freezes/unfreezes the on-screen picture 
17.  VOL + Adjusts volume 
18.  AUTO Auto adjustment for frequency, phase, and position 
19.  VOL - Adjusts volume 
24 
20.  BLANK  Makes the screen blank 
21.  TINT Displays the tint setting bar 
22.  MUTE Mutes the built-in speaker 
23.  STATUS  Opens the OSD Status menu (the menu only opens when an input 
device is detected) 
24.  ASPECT RATIO 
Displays the ASPECT RATIO selections 
25.  MENU 
Opens or closed the OSD 24 
26.  Left cursor  Navigates and changes settings in the OSD 24 
27.  COMP Displays the Component source selection 
28.  VIDEO  Displays the VIDEO source selection 
29.  HDMI 1 Displays the HDMI 1 source selection 
30.  Power ON Turns the projector on 13 
31.  Status LED  Lights when the remote control is used 
32.  IR transmitter Transmits signals to projector 
33.  Wired remote 
connector  Wired remote function used  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
–  9 –  
Remote Control Operating Range 
The remote control uses infrared transmission to c ontrol the projector. It is not necessary to point 
the remote directly at the projector. Provided  you are not holding the remote perpendicular to the 
sides or the rear of the projecto r, the remote will function well with in a radius of about 7 meters (23 
feet) and 15 degrees above or below the projector le vel. If the projector does not respond to the 
remote control, move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using  the remote control or the buttons on the top of the projector. 
All operations can be carried out with the remote  control; however, the buttons on the projector 
are limited in use.   
						

							DLP Projector—User’s Manual 
— 10 — 
SETUP AND OPERATION 
Inserting the Remote  Control Batteries  
1.  Remove the battery compartment 
cover by sliding the cover in the 
direction of the arrow. 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AA batteries (Alkali ne batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods.  
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Installing or Removing  the Optional Lens 
Caution: 
y Do not shake or place excessive pressure  on the projector or the lens components as the 
projector and lens component s contain precision parts. 
y Before removing or installing the lens, be sure to  turn off the projector, wait until the cooling 
fans stop, and turn off the main power switch. 
y Do not touch the lens surface when removing or installing the lens. 
y Keep fingerprints, dust or oil off the lens surface. 
y Do not scratch the lens surface. 
y Work on a level surface with a soft  cloth under it to avoid scratching. 
y If you remove and store the lens, attach the lens  cap to the projector to keep off dust and dirt. 
Removing the Existing Lens From the Projector 
1.  Pull and release the top cover to 
open as shown. 
2.  Push the LENSE RELEASE button 
to the unlock position. 
3.  Grasp the lens. 
4.  Rotate the lens counterclockwise. 
The existing lens will be 
disengaged. 
5.  Pull out the existing lens slowly. 
– 11  –