Vivitek D5180hd Projector User Manual

							DLP Projector—User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
Image Settings
Image Settings>> Advanced(PC Detail Adjustment)
Display Settings
Basic Setup
Information
Display Settings>> HSG Adjustment
Audio Settings
Timer Setup
Advanced Setup
Image Settings>> Advanced(Video Adjustment)
Auto Adjustment
Aspect Ratio
Picture Mode
Brightness
Contrast
Saturation
Tint
Sharpness
Reset
Advanced
Image Position
Phase
Frequency
Projection
Keystone
Color Temperature
Gamma
HSG Adjustment
Primary Color
Hue
Saturation
Gain
White Gain Red
White Gain Green
White Gain Blue
Sleep Timer
Mute
Volume
Auto Power Off
Language
Auto Scan
Menu Settings
Splash Logo
Background Color
Lamp Setting
High Altitude Mode
Network Settings
Reset All
Source
Resolution
Lamp Hour
Firmware Version
Flesh Tone
Noise Reduction
Dynamic Contrast
Movie/Bright/Normal/User 1/User 2/User 3
Lamp Native/Warm/Normal/Cool/Cooler/High Cool
Auto/16:9/4:3/Letter Box/Real
English/ Danish/ Dutch/ Finnish/ Français/ Deutsch/ Italiano/ Korean/ Norsk/ Polish/ Português (Latin American)/
Russian/ Simplified Chinese/ Traditional Chinese/ Spanish/ Swedish/ Turkish/ Bahasa
Yes/No
Up/Down/Left/Right
Front Table/Front Ceiling/Rear Table/Rear Ceiling
R/G/B/Y/C/M
Off/On
Off / 30 Min / 1 Hr / 2 Hr / 3 Hr / 4Hr / 8Hr / 12 Hr
Off / 5 Min / 10 Min / 15 Min / 20 Min / 25 Min / 30 Min
Off/Low/Moderate/High
Logo/Blue/Black
Purple/Blue/Black
Menu position
Display Time
Control By
Network Status
Lamp Mode
Yes/No
Reset Lamp Timer
Off/On
Transparency
Off/On
Top-Left/Top-Right/Center/Bottom-Left/Bottom-Right
5 Sec / 10 Sec / 15 Sec / 20 Sec / 25 Sec / 30 Sec
RS232/RJ45
Network State /  DHCP (On /  Off) / IP Address /  SubNet Mask /
Default Gateway  / DNS / Apply
Yes/No
Boost/Standard
White BalanceRed Gain/Green Gain/Blue Gain/Red Offset/Green Offset/Blue Offset
V Keystone/H Keystone/Reset
 
— 22 —  
						

							 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Image Settings  
Press the MENU  button to open the  OSD menu. Press the cursor  ▲▼ button to move to the  Image 
Settings  menu. Press  ENTER / ►  button to move up and down in the  Image Settings  item. Press 
ENTER  / ►  button to entry item. Press  ▲▼ or ◄►  to change values for settings. 
 
ITEM DESCRIPTION 
Picture Mode  Press the cursor ▲▼ button to set the Picture Mode.  
Brightness  Press the cursor ◄► button to adjust the display brightness. 
Contrast  Press the cursor ◄► button to adjust the display contrast. 
Saturation  Press the cursor ◄► button to adjust the Saturation. 
Tint  Press the cursor ◄► button to adjust the Tint. 
Sharpness  Press the cursor ◄► button to adjust the display sharpness level. 
Advanced Press  ENTER / ►  to enter the Advanced menu. See  Advanced Feature  on page 24. 
Reset  Press the cursor 
▲▼ button to set the “YES” or :NO”.  Press  ENTER to reset Picture 
Mode default values. 
 
–  23  –  
						

							DLP Projector—User’s Manual 
Advanced Feature 
Press the Menu button to open the OSD menu. Press  ▲▼ to move to the  Image Settings  menu. 
Press  ENTER  / ►  button in the  Advanced item. Press  ENTER / ►  button to entry item.Press ▲▼to 
move to the  Advanced item and then press  ENTER or ►or  ◄►  to setting value. 
 
PC Detail Adjustment 
 
ITEM DESCRIPTION 
Auto Adjust  Press 
ENTER  or ► button; or Press the  Auto button on the projector keypad or the 
Auto  button on the remote control to automa tically adjust frequency, phase, and posi-
tion. 
Image Position  Press 
ENTER  / ► button to Image Position submenu,  Press the ▲▼ or ◄►  buttons 
to Enter H/V position adjust Image Position. 
This function is only available when a PC signal (analog RGB) is selected.  
Phase Press  the ◄►  buttons to adjust the A/D sampling clock. 
Frequency Press the  ◄► buttons to adjust the A/D sampling number. 
 
Image Position 
 
—  24 —  
						

							 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
 
Video Adjustment 
 
ITEM DESCRIPTION 
Noise Reduction  Press 
ENTER  / ► button to enter Noise Reduction submenu,  Press the cursor ◄► 
button to adjust the Noise Reduction. 
Flesh Tone  Press the cursor ▼▲ button to select different Flesh Tone.  
Dynamic Contrast  Press the cursor ▼▲ button to select different Dynamic Contrast. 
 
Noise Reduction 
 
 
–  25  –  
						

							DLP Projector—User’s Manual 
Display Settings  
Press the MENU button to open the  OSD menu. Press the cursor  ▲▼ button to move to the  Display 
Settings  menu. Press  ENTER / ►  button to move up and down in the  Display Settings item. Press 
ENTER  / ►  button to entry item. Press▲▼  or ◄►  to change values for settings. 
 
ITEM DESCRIPTION 
Aspect Ratio  Press the cursor▲▼
button to set the Aspect Ratio. 
(Range:  Auto/ 16:9/ 4:3/ Letter Box/ Real) 
Keystone  Press the 
ENTER/ ► button to enter the Keystone sub menu. 
(This function will be disabled when  Auto keystone is activated) 
Projection  Press the cursor▲▼button to select different projection type. 
Gamma  Press the cursor ◄► button to adjust the gamma correction of the display. 
Color Temp  Press the cursor▲▼button to set the Color Temp 
HSG Adjustment  Press the 
ENTER/ ► button to enter the  HSG (Hue/Saturation/Gain)  Adjustment sub 
menu.  
See  HSG Adjustment  on page 28
 
White Balance  Press the 
ENTER/ ► button to enter the  White Balance sub menu.  
See  White Balance  on page 29 
 
— 26 —  
						

							 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Keystone 
Press the ENTER/  ► button to enter the  Keystone sub menu. Press  ◄► to change values for set-
tings. 
 
V Keystone  Press the cursor 
◄► button to adjust the V Keystone  
(This function will be disabled when  Auto keystone is activated) 
H Keystone  Press the cursor 
◄► button to adjust the H Keystone  
(This function will be disabled when  Auto keystone is activated) 
Reset Press  ENTER  button to reply Keystone default values. 
 
Applying keystone to correct image due to projection angl e will result in minor distortion compared to 
actual image 
 
 
–  27  –  
						

							DLP Projector—User’s Manual 
HSG Adjustment 
Press the ENTER/ ► button to enter the  HSG Adjustment item. Press▲▼ or ◄►  to change values 
for settings. 
 
ITEM DESCRIPTION 
Primary Color  Press the 
▲▼ buttons to set the Primary Color. 
Notes:  There are six colors ( R/ G/ B/ C/ M/ Y) to be customized. 
Hue Press  the ◄►  buttons to adjust the Hue. 
Saturation Press  the ◄►  buttons to adjust the Saturation. 
Gain Press  the ◄►  buttons to adjust the Gain. 
White Gain Red  Press the cursor ◄► button to adjust the White Gain Red. 
White Gain Green  Press the cursor ◄► button to adjust the White Gain Green. 
White Gain Blue  Press the cursor ◄► button to adjust the White Gain Blue. 
 
— 28 —  
						

							 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
White Balance 
Press the ENTER  button to enter the  White Balance sub menu.  
 
ITEM DESCRIPTION 
Red Gain  Press the ◄► buttons to adjust the Red Gain. 
Green Gain  Press the ◄► buttons to adjust the Green Gain. 
Blue Gain  Press the ◄► buttons to adjust the Blue Gain.  
Red Offset  Press the ◄► buttons to adjust the Red Offset. 
Green Offset  Press the ◄► buttons to adjust the Green Offset. 
Blue Offset  Press the ◄► buttons to adjust the Blue Offset. 
 
– 29  –  
						

							DLP Projector—User’s Manual 
Audio Settings 
Press the MENU button to open the  OSD menu. Press the cursor ▲▼ button to move to the  Audio 
Settings  menu. Press  ENTER / ►  button to move up and down in the  Audio Settings  item. Press 
ENTER  / ►  button to entry item. Press▲▼  or ◄►  to change values for settings. 
 
ITEM DESCRIPTION 
Volume  Press the 
◄► buttons to adjust the audio volume.  
(Range: 0~10) 
Mute Press  the ▲▼  buttons to turn on or off the speaker. 
 
 
— 30 —  
						

							 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Timer Setup 
Press the MENU  button to open the  OSD menu. Press the cursor ▲▼ button to move to the  Timer 
Setup  menu. Press  ENTER / ►  button to move up and down in the  Timer Setup item. Press ENTER  
/ ►  button to entry item. Press the cursor  ▲▼ button to move up and down in the  Timer Setup item. 
Press ▲▼to change values for settings. 
 
ITEM DESCRIPTION 
Sleep Timer  Press the cursor▲▼
buttons to set Sleep timer. The projector automatically turns off 
after the preset period of time.  
(Range:  Off/ 30 min/ 1hr/ 2hr/ 3hr/ 4hr/ 8hr/ 12hr). 
Auto Power Off  Press the cursor▲▼
buttons to set the Auto Power Off timer. The projector automati-
cally turns off if no input source is detected after the preset period of time. 
(Range:  Off/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min). 
 
– 31  –