Vivitar Vivicam 4345 Users Manual

							Downloaded from www.Manualslib.com manuals search engine EN-41
VIDEO MODE
Recording Video Clips
This mode allows you to record video clips with sound via built-in microphone.
1. Rotate the mode dial to 
 mode and turn your camera on by
pressing the  button.
2. Press the shutter button to start recording.
3. To stop recording, press the shutter button again.
„The zoom function of optical zoom (3x) can be activated before you start to record video clips.
„Pressing the  button switches the LCD monitor display mode.  Press the  button once to set the indicators
OFF. Press the  button again to set the indicators ON.
SD00:49
[   ]  
						

							Downloaded from www.Manualslib.com manuals search engine EN-42
Playing Back Video Clips
You can play back recorded video clips. A guide to operation appears on the LCD monitor during the
video playback.
1. Press the  
 (Playback) button.
2. Use W or X to go through the images until the video clip you
want to play back is displayed.
„ „„ „
„To view the previous image, press the W button.
„ „„ „
„To view the next image, press the X button.
3. Press the 
 button to start playing back the video clips.
„ „„ „
„To pause or resume video playback, press the 
 button
again.
„The playback information displayed on the LCD monitor will disappear after seconds of time.
„The zoom function cannot be activated while playing the video clips back.
„To playback the video clips on the computer, we recommend you to use Windows Media Player 9.0 (WMP 9.0).
You can download WMP version from the website at www.microsoft.com.
SD
100-0001
SIZE
EV.
01. 04. 041280X960
+1.5
05:22
1  
						

							Downloaded from www.Manualslib.com manuals search engine EN-43
PLAYBACK MODE – ADVANCED FEATURES
Playing Back Still Images/Video Clips on TV
You can also playback your images on a TV screen. Before connecting to any device, make sure to
select NTSC/PAL system to match the video output system of the video equipment you are going to
connect to ViviCam 4345, then turn all connected devices off.
1 . Connect one end of the A/V cable to the A/V terminal of ViviCam
4345.
2. Connect the other end to the A/V input socket of the TV set.
3. Turn the TV and ViviCam 4345 on.
4. Playback the images/video clips.
„ „„ „
„The method of operation is the same as playing back still
images and video clips on ViviCam 4345.
VT
„The sound recorded with video clips can only be played back on TV or computers.  
						

							Downloaded from www.Manualslib.com manuals search engine EN-44
Deleting Images/Video Clips
Use this function to delete one or all images/video clips stored in the internal memory or memory card.
Please note that the deleted images or video clips cannot be recovered. Exercise caution before
deleting a file.
„
 To delete the latest single image/video clip
1. Press the  button to turn on the power.
2. Press  . When the delete message appears, use S or T to
select [YES], then press the  button to delete the last image
or video clip.
„ „„ „
„If you wish to cancel the deletion, select [NO].
„ To delete image/video clip by preference
1. Press the  (Playback) button.
„ „„ „
„The last recorded image appears on the LCD monitor, which
can also be deleted directly by pressing 
.
2. Use W or X to select the image you want to delete.
3 . Press 
 , then use S or T to select [DELETE] and press the 
button.
4. Use S or T to select [THIS IMAGE] or [ALL IMAGES] by your
preference, then press the 
 button.
5 . When the delete message appears, use S or T to select [YES],
then press the 
 button to confirm the deletion.
„ „„ „
„If you wish to cancel the deletion, select [NO].
„ „„ „
„Protected images cannot be deleted with the delete function.
SET :
DELETEYES
NO
DELETE
SET :RETURN :
THIS IMAGE
ALL IMAGES
PLAYBACKDELETE
SLIDE SHOW
PROTECT
QUALITY CHANGE
1 / 7SET :EXIT :  
						

							Downloaded from www.Manualslib.com manuals search engine EN-45
Protecting Images/Video Clips
Set the data to read-only to prevent images from being erased by mistake.
1. Press the 
 (Playback) button.
„ „„ „
„ The last recorded image appears on the LCD monitor.
2 . In 
 (Playback) mode, use W or X to select the desired images.
„ „„ „
„ To view the previous image, press the W button.
„ „„ „
„ To view the next image, press the X button.
3. Press 
 , then use T to select [PROTECT] and press the 
button.
4. Use S or T to choose the desired setting, then press the
 button.
„ „„ „
„[PROTECT ONE]: Protect one image/movie.
„ „„ „
„[PROTECT ALL]: Protect all images/movies (at once).
5. Use S or T to select [LOCK], then press the 
 button to
confirm.
„ „„ „
„Press 
 to return to the  (Playback) mode.
The   indicator appears on the selected image.
„ „„ „
„If you wish to cancel the protect function, select [UNLOCK].
PROTECT
SET :RETURN :
PROTECT ONE
PROTECT ALL
PROTECT ONE
SET :RETURN :
LOCK
UNLOCK
PLAYBACK
SLIDESHOW
DELETE
SLIDE SHOW
PROTECT
QUALITY CHANGE
3 / 7  
						

							Downloaded from www.Manualslib.com manuals search engine EN-46
TRANSFERRING FILES FROM YOUR VIVICAM 4345
TO COMPUTER
After using USB cable to establish a USB connection between ViviCam 4345 and your computer, you can
use your computer to share recorded images or video clips with your family or friends via e-mail or post them
on the Web. In order to do this, you must install the USB driver onto your computer first. Note that before
you begin to install the software, you need to check your system according to the table as shown below.
System Requirements System Requirements
(Windows) (Macintosh)
CPUPentium III 600 MHz processor or higher G3/G4
Operating SystemWindows ME/2000/XP OS X
RAM32MB 32MB
Hard Disk Space128MB hard disk space 128MB hard disk space
Required DevicesA CD-ROM drive A CD-ROM drive
An available USB port An available USB port  
						

							Downloaded from www.Manualslib.com manuals search engine EN-47
Step 1: Install the USB driver
„Installation on Windows 98 & 98SE
The USB driver on the supplied CD-ROM is exclusively for Windows 98 and \
98SE. Windows 2000/ME/XP
users need not install the USB driver.
1. Insert the enclosed CD-ROM into your CD-ROM drive.
2 . When the welcome screen appears, click “ Install USB Driver”.
Follow  the on-screen instructions to complete the installation.
3. After the USB driver has been installed, restart your computer.
„ Installation on MAC OS 9.0
For Mac OS 9.0 or higher, the computer will automatically recognize Vivi\
Cam 4345 and load its own USB
drivers.  
						

							Downloaded from www.Manualslib.com manuals search engine EN-48
Step 2: Connect ViviCam 4345 to your computer
1. Rotate the mode dial to  and turn your camera on by pressing
the 
 button.
2. Connect one end of the USB cable to an available USB port on
your computer.
3. There will be a new “Removable Disk” icon detected in “My
Computer”, in which contains your recorded images or video
clips.
(For Mac users, double-click [untitled] or [unlabeled] disk drive
icon on our desktop.)  
						

							Downloaded from www.Manualslib.com manuals search engine EN-49
Step 3: Download images or video clips
When ViviCam 4345 is turned on and connected to your computer, it is considered to be a disk drive, just
like a floppy disk or CD. You can download (transfer) images by copying them from the “Removable disk”
(“untitled” or “unlabeled” disk on a Macintosh) to your computer hard drive.
„Windows
Open the “removable disk” and double click on the DCIM / DSCIM folder to open it to find more folders.
Your images are inside these folder(s). Select the desired still images or video clips and then choose
“Copy” from the “Edit” menu. Open the destination location (folder) and choose “Paste” from the “Edit”
menu. You may also drag and drop image files from ViviCam 4345 to a desired location.
„ „„ „
„Macintosh
Open the “untitled” disk icon, and the destination location on your hard disk. Drag and drop from ViviCam
4345 to the desired destination.
„Memory card users may prefer to use a memory card reader (highly recommended).
„Video playback application is not included with the package. Make sure that video playback application has
been installed in your computer.  
						

							Downloaded from www.Manualslib.com manuals search engine EN-50
EDITING SOFTWARE INSTALLATION
Installing Photo Explorer
Ulead® Photo Explorer provides a simple and efficient way to transfer, browse,\
 modify and distribute
digital media. Acquire photos, video or sound clips from various digital\
 device types and easily browse
or add personal descriptions; make timely modifications; or distribute t\
he media through the medium of
your choice: E-mail, Print, Slideshow Presentations. It is an indispensa\
ble all-in-one tool for owners of
digital cameras, DV camcorders, scanners, or anyone who strives to effec\
tively organize a large collection
of digital media.
1. Insert the enclosed CD-ROM into your CD-ROM drive.
2 . When the welcome screen appears, click “ Install Ulead
® Photo
Explorer ”. Follow the on-screen instructions to complete the
installation.
„ For more information about the operation of Photo Explorer application s\
oftware, refer to its respective help
documentation.
„ For Windows 2000/XP users, please make sure to install and use the Photo\
 Explorer in “Administrator” mode.
„ Photo Explorer is not supported on the Mac. iPhoto or iPhoto2 is recomme\
nded.