ViewSonic Projector Pro8500 User Manual

							ViewSonic  Pro8500 49
4. The Basic Setting page allows you to configure pwPresenter.
i. To change the pwPresenter interface language, click the down arrow to 
reveal a drop-down list and select a desired language. Click Apply.
ii. Users can change the size parameters of the frame in FixedSize capture 
mode by modifying width and height on this page and click Apply to make 
changes take effect. 
iii. User can use the mirror driver for presenter capture image, if the system 
has installed the mirror driver.
iv. To allow notification messages to appear, click Yes. Click Apply.
v. The Software Information is available on this page.
v
iviii
ii
i 
						

							ViewSonic  Pro8500 50
5. The Advanced Setting page allows you to configure pwPresenter.
i. To adjust the image quality, click the down arrow to reveal a drop-down list 
and select a desired quality level. Click Apply.
ii. To adjust the capture rate, move the slide bar. The network bandwidth may 
also affect the performance.
iii. Network port setting for fixed or manual type.
i
ii
iii 
						

							ViewSonic  Pro8500 51
6. Network Display Management displays the Device Management and pwPresenter 
Management information.
Device Management allows you to change device settings
.
i. Click to change display port allows you to select display location of screen. 
ii. Change password allows you to change password for the user type.
iii. Disconnect allows you to disconnect the projector from network.
iv. Access device via webpage allows you to access ViewSonic webpage con-
trol system.
v. View device status displays device setting information and allows you to 
enter conference control mode.
i
ii
iii
iv
v 
						

							ViewSonic  Pro8500 52
pwPresenter Management allows you to select which computer to be connected 
and transfer the desktop content to the network projector.
7. Disconnect allows you to disconnect from the projector(s) by clicking the 
Disconnect icon.
Important
„Be sure to turn off other virtual network control programs before using 
pwPresenter. 
						

							ViewSonic  Pro8500 53
Displaying pictures with a USB storage device
The built-in the ImageViewer application can display packaged images on a USB 
storage device (e.g. USB flash drive, and USB disk), a digital camera, or other device. 
You can connect a USB storage device to your projector.
1. Take a USB cable and connect the larger end to the USB A socket on the 
projector, and smaller end to the USB port of the device. If you are using a USB 
flash drive, connect it directly to the 
USB A socket.
2. The projector automatically display the thumbnails. Or your can manually select 
USB Reader from the source selection bar.
3. The ImageView main screen is displayed and ready to use. The main screen is 
displayed in Thumbnail Display Mode which shows the following four parts:
i. Current path, USB storage device name and page number
ii. File and folder name display (i18N, multi-language)
iii. Thumbnail images (120 x 120 pixels images)
iv. Operation User Interface
4. Use the four directional buttons or page up/down button to move between pages/
folders. To Press and hold Menu and then press Enter to display the operation 
user interface. Use  /  to select the desired item and adjust the settings with  
/ . To confirm the selection press Enter. The following buttons are supported 
in the user interface.
„Next: Display next page.
„Previous: Display previous page.
iv
i
iii
ii 
						

							ViewSonic  Pro8500 54
„Thumbnail/Slide show/Display: Display thumbnails, start the slide show or 
display the selected image.
„Name Order/Extend Order/Size Order/Time Order: Select the order setting 
by file/folder name, extended file name, image size or time.
„EXIF ON/EXIF OFF: Display the Exif information of the image or not.
„File Name On/File Name Off: Display the file name or not.
The projector supports the following image formats:
„JPEG (JPG)
„Bitmap (BMP)
„Portable Network Graphic (PNG)
„Graphics Interchange Format (GIF)
„Tagged Image File Format (TIFF) 
						

							ViewSonic  Pro8500 55
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt 
or spots will project on the screen and diminish image quality. If any other parts need 
replacing, contact your dealer or qualified service personnel. When cleaning any part 
of the projector, always switch off and unplug the projector first.
Warning
Never open any of the covers on the projector. Dangerous electrical voltages 
inside the projector can cause severe injury. Do not attempt to service this 
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth 
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Cleaning the Filter Cover
The filter cover, which is located at the side of the projector, should be cleaned after 
every 100 hours of use. If it is not cleaned periodically, it can become clogged with 
dust and prevent the projector from being ventilated properly. This can cause over 
heating and damage the projector.
To clean the filter cover:1. Switch the projector off and unplug the AC 
power cord from the wall socket.
2. Remove the filter cover as the illustration 
shown.
3. Clean the filter cover.
„To clean the filter cover, you are 
advised to use a small vacuum 
cleaner designed for computers and 
other office equipment.
„If the filter cover is torn, replace it.4. Replace the filter cover.
5. Attach the filter cover.  
6. Plug the power back into the projector.
„Turn off the projector and remove the AC power cord from the power outlet 
before beginning maintenance work.
„Make sure the lens is cool before cleaning.„Do not use detergents or chemicals other than those noted above. Do not use 
benzene or thinners.
„Do not use chemical sprays.„Use a soft cloth or lens paper only. 
						

							ViewSonic  Pro8500 56
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually 
decreases and the lamp becomes more susceptible to breakage. We recommend 
replacing the lamp if a warning message is displayed. Do not attempt to replace the 
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp is extremely hot right after turning off the projector. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait for at least 
45 minutes for the lamp to cool down.
„Do not touch the lamp glass at any time. The lamp may explode due to 
improper handling, including the touching of the lamp glass.
„Lamp lifetime may differ from lamp to lamp and according to the environment 
of use. There is no guarantee of the same lifetime for each lamp. Some lamps 
may fail or terminate their lifetime in a shorter period of time than other similar 
lamps.
„A lamp may explode as a result of vibration, shock or degradation as a result of 
hours of use as its lifetime draws to an end. Risk of explosion may differ 
according to the environment or conditions in which the projector and lamp are 
being used.
„Wear protective gloves and eyeglasses when fixing or detaching the lamp.„Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least 
for 5 minutes to turn off the projector after powering on.
„Do not operate the lamp in proximity to paper, cloth, or other combustible 
material nor cover it with such materials.
„Do not operate the lamp in an atmosphere containing an inflammable 
substance, such as thinner.
„Thoroughly ventilate the area or the room when operating the lamp in an 
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, 
nausea, dizziness, and other symptoms.
„The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury 
inside the lamp will be exposed. Leave the area immediately if the lamp 
shatters while being operated and ventilate the area for at least 30 minutes in 
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to 
user’s health. 
						

							ViewSonic  Pro8500 57
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the 
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try 
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Information” menu.
„Dispose the used lamp according to local regulations.„Ensure that screws are tightened properly. Screws not tightened fully may 
result in injury or accidents.
„Since the lamp is made of glass, do not drop the unit and do not scratch the 
glass.
„Do not reuse the old lamp. This could cause the lamp to explode.„Be sure to turn off the projector and unplug the AC power cord before 
replacing the lamp.
„Do not use the projector with the lamp cover removed. 
						

							ViewSonic  Pro8500 58
Specifications
Display system Single 0.7 DLP panel
Resolution XGA (1024 × 768 pixels)
Zoom 1.5X
F/No. 2.41 - 2.97
Focal length 20.72 - 31mm
Screen size 30 - 300
Lamp 280W
Input terminal D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input (3.5 
mm stereo mini jack) x 2, HDMI x 1, Component RCA jack x 1, 
RCA audio jack (L/R) x 1, 3.5 mm Mic input x1, USB  A type x1 
(supports USB flash drive display and wireless dongle for USB 
display), USB mini-B type x1 (supports USB display)
Output terminal D-Sub 15 pin x 1,  Audio signal output (3.5 mm stereo mini jack) x 
1
Control terminal RS-232 x 1, USB B type x 1 (supports firmware upgrade and 
remote mouse control), RJ45 x 1, 12-Vdc trigger output x 1
Speaker 10 watt x 2
Video compatibility NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency31 - 100 KHz
50 - 120 Hz
Environment Operating:
Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power requirement AC 100-240 V, 50 - 60 Hz, 3.8A
Power consumption 380 W
Dimension (W x D x H) 334.6 x 264.5 x 109.5 mm
Weight 3.9 kg (8.6 lb)
Note: Design and Specifications are subject to change without prior notice.