ViewSonic Projector PJD8653ws User Manual

40
Timer
Timer Period
Select timer period from 1 to 240 min.
Timer Display
Select timer display from 1 min, 2 min, 3 min, Never or Always.
Timer Position
Select timer position from Top Left, Top Right, Bottom  Left or Bottom R\
ight.
Timer Counting Direction
Set the count down or count up timer interval.
Start Counting
Turn on/off the Presentation timer.
Presentation TimerTimer Period
Timer Display
Timer Position
Timer counting direction
Start Counting 1 min
Bottom Right
Count Down
Select
Enter Exit  

41
1. Turn on DHCP to allow a DHCP server to automatically assign an IP, or 
manually enter the required network information.
LAN Settings
DHCP
IP Address
Subnet Mask
Gateway
DNS
Store
Reset Off
Select
Enter Exit
2. Open your web browser and type in IP Address from the OSD LAN. 
3.  Based on network web-page for the input-string in [tools] tab, the limit\
ation for 
Input-Length is in the below list (“space” and the other punctuat\
ion key included): 
Category ItemInput-Length 
 
(characters)
Projector...

42
When making a direct connection from your computer to the projector
Step 1: Find an IP Address (192.168.10.100) from LAN function of projector.
Step 2: To open Network Connections, 
click Start, click Control Panel , 
click Network and Internet 
Connections, and then click 
Network Connections. Click the 
connection you want to configure, 
and then, under  Network Tasks 
 , click Change settings of this 
connection .
Step 3: On the General tab, under This  connection uses the following 
items, click...

43
Web Management
Projector Information
LAN Setting
Projector Status and Control
E-mail Setting
Security Setting
Firmware UpdateLAN Settings
Model Name:
Projector Name:
Location:
Administrator:
Save
DHCP
PJD8653wsD21211
Manual
IP Address
Subnet Mask
Gateway
DNS Server
Save
IP Address
Device ID
Port
Save
Crestron Control System Device
Projector Information Page
 
` Projector Information page by entering the projector’s IP address at \
the web 
browser. See “LAN Settings” section.
 
` Language: Allows you...

44
Projector Status and Control Page
 
` Projector Status: There are 4 status: Standby, Warning up, Lamp On, Powe\
r 
Saving and Cooling. Click the Refresh button to refresh the status and c\
ontrol 
settings. 
 
` Auto Power Off: Auto Power Off can be set to Off(0) or 1~120 minutes. \
See “Auto 
Power Off (min)” function.
 
` Alert Status: There are three error status: Lamp warning, Low lamp life,\
 and 
Temperature warning. Your projector might lock up in protection mode if \
any of 
the alerts is...

45
Web Management
Projector Information
LAN Setting
Projector Status and Control
E-mail Setting
Security Setting
Firmware UpdateSecurity Setting
Password
New Password
Confirm PasswordSubmitAdministratorSubmitEnableDisable
Please set your password if you enable this feature for first-time. If password 
is set, you will require to enter with your password upon you connect to\
 the 
Web Management.
E-mail Setting Page
 
` E-mail Alert: You can set whether to be notified by email (Enable) or not (Disable)....

46
Web Management
Projector Information
LAN Setting
Projector Status and Control
E-mail Setting
Security Setting
Firmware Update
Network Firmware Version: Gen_v0.62
Update
Firmware UpdateFirmware update will take about a minute. Do not interrupt the process 
once it has begun. Keep the connection established until completion 
of process. The network system will auto reboot and you can re-login after update is complete. 
Cancel
Login Page
 
` Administrator Password: Enter the Administrator Password and...

47
3. Select the file to upgrade and click the Upgrade button. When upgrading is in 
progress, the Cancel button is disabled.
Upgrade must NOT be interrupted !
(Upgrading firmware may take 60 seconds)
UpgradeCancel
Please select a file (~.bin) to upgrade: Browse...
Upgrade Firmware
4. 
When upgrade is complete, please click the Re Login button to go back to\
 
the Web Management page.
Please wait.
Click on button to proceed after 8 seconds.
Re Login
Crestron
 
` For more information, please visit...

48
Troubleshooting
Appendices
If you experience a problem with your projector, please refer to the follow-
ing information. If a problem persists, please contact your local resell\
er or 
service center.
Image Problems
   No image appears on-screen
 
` Ensure all the cables and power connections are correctly and securely 
connected as described in the “Installation” section.
 
` Ensure the pins of connectors are not crooked or broken.
 
` Check if the projection lamp has been securely installed.
 
`...

49
 
- If the projector is still not projecting the whole image, you will also \
need to change the monitor display you are using. Refer to the 
following steps.
1. Select the “Change” under the “Monitor” tab.
2.  Click on “Show all devices”. Next, select “Standard monitor types” 
under the SP box; choose the resolution mode you need under 
the “Models” box.
3.  Verify that the resolution setting of the monitor display is lower 
than or equal to 1080p.
 
yIf you are using a Notebook:
 
- First, follow...