ViewSonic Projector PJD7325 User Manual

 40
SYSTEM SETTING: BASIC
Language
Select the language used by the on-screen menu.
Projector Position
Adjust the picture to match the orientation of the projector: upright or upside-down, in 
front of or behind the screen. Invert or reverse the image accordingly.
Menu Settings
Menu Display Time
Duration of OSD menu display countly starts (at idle state by second).
Menu Position
Choose the menu location on the display screen.
Blank Timer
Sets the image blank time when the Blank Timer feature is activated,...

 41
SYSTEM SETTING: ADVANCED
High Altitude Mode
Use this function to allow the fans operates at full speed continuously to achieve 
proper high altitude cooling of the projector.
DCR
DCR (Dynamic Contrast Ratio): Enable DCR will further enhance contrast ratio by 
darkening the black scenes. Disable DCR will resume to normal contrast 
performance. DCR will impact lamp life and system noise performance.
Audio Settings
See Adjusting the sound on page 50 for details.
Audio Mode
Press  /  to select a...

 42
Reset the lamp Hour to 0 hours.
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Filter Settings (Optional)
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter 
cover.
Reset Filter Hours
Reset the filter Hour to 0 hours.
Filter Hours
Display the filter’s elapsed operating time (in hours).
Remote Control Code
See Remote control code on page 10 for details.
Advanced
Security Settings
• Change Password: Allows you to set or change the...

 43
INFORMATION
Current System Status
Shows the currect system status.
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the Color Mode menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Lamp Hours
Displays the number of hours the lamp has been used.
Filter Hours
Displays the number of hours the filter has been used.
IP Address
Display the IP address.
MAC Address
Display the MAC address.
Firmware...

 44
Controlling the projector through a LAN environment
You can manage and control the projector from one or more remote computers when 
they are properly connected to the same local area network.
If you are in a DHCP on environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the 
projector and the other end to the RJ45 port on your Ethernet or router.
2. Press Menu and then go to SOURCE > LAN Control Settings menu.
3. Make sure the LAN Settings is DHCP on.
4. Press 
 to...

 45
Important
• If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, 
Default Gateway and DNS Server settings will display 0.0.0.0. Make sure the cables are 
properly connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected 
RJ45 and obtained the Projector IP Address, Subnet Mask, Default Gateway and DNS 
Server information when the projector is on.
Controlling the projector remotely through...

 46
3. This page allows you to make adjustments to the AMX and SNMP settings. In the 
AMX device discover row, when ON is selected, the projector can be detected by 
controllers of AMX connected to the same network. For the Details of AMX Device 
Discovery, visit the AMX web site at http://www.amx.com/.
4. If your projector is connected to a network which supports Simple Mail Transfer 
Protocol (SMTP), you can configure it to alert you via email on significant events.
5. The Crestron (e-Control) page...

 47 • / > < $ % +    are prohibited. 
About Crestron e-Control®
1. The Crestron e-Control
® page provides a variety of virtual keys to control the 
projector or adjust the projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote 
control. 
ii. To switch input source, click on your desired signal.
Important
• The Menu button can also be used to go back to previous OSD menu, exit and save 
menu settings.
• The source list varies according to the connectors available on...

 48
i. This section is only used with the Crestron Control System. Please contact 
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge 
of it.
iii. You can adjust the Lan control setting.
iv. Once set, access to the remote network operation on this projector has been 
password-protected.
v. Once set, access to the tools page has been password-protected.
• To prevent errors, only input the English alphabet and...

 49
3. The info page displays the information and status of this projector.
i. Press exit to go back to the Crestron remote network operation page.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in 
the upper right corner of the screen. You will be able to deliver messages to 
RoomView™ software administrators/users who connect to the same local area 
network. 
• For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
Crestron RoomView
On the...