ViewSonic Projector PJD6551W User Manual

36
To cancel the timer, p
erform the following steps:
1. Press   on the remote control or go to the  SYSTEM SETTING: BASIC > 
Advanced > Presentation Timer  menu.
2. Highlight  Off. Press  Enter. A confirmation message displays.
3. Highlight  Yes and press  Enter to confirm. You will see the message “ Timer is Off” 
displaying on the screen.
Hiding the image
In order to draw the audiences full  attention to the presenter, you can press  BLANK to hide 
the screen image. Press any key on the project or or...

37
4. A confirmation message displays. Press Enter again.
5. The message Screen Capturing... displays  while the projector is processing the 
picture. Please wait.
6. If the action is successful, you see the message Captured Succeeded on the screen.  The captured picture is saved as  Screen Capture and have been set as your current 
startup screen.
In the unlikely event that the capturing action  fails, change your target picture. When the 
resolution of the input signal is higher than th e projector’s...

38
Using the 3D functions
This projector features 3D function which enables you to enjoy 3D movies, videos, and 
sporting events in a more realistic way by presenting the depth of the images. You need to 
wear a pair of 3D glasses to view 3D images.
If the 3D signal is input from  an HDMI 1.4a compatible de vice, the projector detects the 
signal for  3D Sync information and once detected, it  projects images in 3D format 
automatically. In other cases, you may need to manually select a 3D Sync  format...

39
Controlling the projector through a LAN 
environment (for selected models)
The projector supports Crestron® software. With correct settings for the  LAN Control 
Settings menu, you can manage the projector from  a computer using a web browser when 
the computer and the projector  are properly connected to the same local area network. 
Configuring the LAN Control Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to  the RJ45 LAN input jack of the projector 
and the...

40
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default 
Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are properly 
connected and perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have selected 
Static 
IP and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server 
information when the projector is on.
Controlling the projector through a web browser...

41
4. If your projector is connected to a network which supports Simple Mail Transfer 
Protocol (SMTP), you can conf igure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays  the Crestron e-Control user interface. See 
About Crestron e-C ontrol® on page 43 for details.  

42
Please pay attention to the limitation of input length (including space and other punctuation 
keys) in the list blow:
 / > < $ % +      are prohibited.
Category ItemInput LengthMaximum Number 
of Characters
Network Settings Network
DHCP/Manual (N/A)
IP Address XXX.XXX.XXX.XXX
Subnet Mask XXX.XXX.XXX.XXX
Gateway XXX.XXX.XXX.XXX
DNS Server XXX.XXX.XXX.XXX
AMX device discovery (N/A)
Password Administrator (N/A)
New Password 4
Confirm Password 4
SNMP SysLocation 22
SysName 22
SysContact 22
Email Alert...

43
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote control.  See  2. PICTURE menu on page 54  and Projector on page 7 for details.
ii. To switch between input signals , click on your desired signal.
The Menu button can also be used to go back to previous OSD menus, exit and save menu 
settings.
The source list varies according...

44
iii. You can adjust the LAN Control Settings .
iv. Once set, access to the remote network operation on this projector has been  password-protected.
v. Once set, access to the tools pa ge has been password-protected.
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for the 
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limi tation of...

45
3. The info page displays the information and status of this projector.
4. After pressing the button “Contact IT Help ”, the HELP DESK window will appear in 
the upper right corner of the screen. You will be able to deliver messages to 
RoomView™ software administrators/users  who connect to the same local area 
network.
For more information, visit  http://www.crestron.com & www.crestron.com/getroomview . 
**Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the...