ViewSonic Projector PJD6351LS User Manual

34
Go to the PICTURE > Color Temp. menu and press /.
The options available for color temperature* settings vary according to the signal type 
selected.
1.Cool: With the highest color temperature, Cool makes the image appear the most 
bluish white than other settings.
2.Neutral: Makes images appear bluish white.
3.Normal: Maintains normal colorings for white.
4.Warm: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be white for various...

35
Please refer to the illustration to the right for 
how the colors relate to each other.
For example, if you select Red and set its 
range at 0, only pure red in the projected 
picture will be selected. Increasing its range 
will include red close to yellow and red close 
to magenta.
5. Press   to highlight Saturation and adjust 
its values to your preference by pressing /
. Every adjustment made will reflect to the 
image immediately.
For example, if you select Red and set its 
value at 0, only the...

36
6. Press   to highlight Timer Counting Direction and select your desired counting 
direction by pressing /.
7. Press   to highlight Sound Reminder and decide if you want to activate sound 
reminder by pressing /. If you select On, a double beep sound will be heard at 
the last 30 seconds of counting down/up, and a triple beep sound will be produced 
when the timer is up.
8. To activate the presentation timer, press   and press / to highlight Start 
Counting and press Enter.
9. A confirmation message...

37
Keys on the remote control are still functional when panel key lock is enabled.
If you press  Power to turn off the projector without disabling panel key lock, the projector 
will still be in locked status the next time it is turned on.
Creating your own startup screen
In addition to selecting the projector preset startup screen from among Black, Blue, or 
ViewSonic screen, you can make your own startup screen that is a picture projected from 
your computer or video source.
To create your own startup...

38
Using the CEC function
This projector supports CEC (Consumer Electronics Control) function for synchronized 
power on/off operation via HDMI connection. That is, if a device that also supports CEC 
function is connected to the HDMI input of the projector, when the projector’s power is 
turned off, the power of the connected device will also be turned off automatically. When 
the power of the connected device is turned on, the projector’s power will be turned on 
automatically.
To turn on the CEC...

39
Controlling the projector through a LAN 
environment
The projector supports Crestron® software. With correct settings for the LAN Control 
Settings menu, you can manage the projector from a computer using a web browser when 
the computer and the projector are properly connected to the same local area network. 
Configuring the LAN Control Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector 
and the other end to the RJ45 port....

40
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default 
Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are properly 
connected and perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have selected 
Static 
IP and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server 
information when the projector is on.
Controlling the projector through a web browser...

41
4. If your projector is connected to a network which supports Simple Mail Transfer 
Protocol (SMTP), you can configure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See 
About Crestron e-Control® on page 42 for details. 
Please pay attention to the limitation of input length (including space and other punctuation 
keys) in the list blow:
Category ItemInput LengthMaximum Number 
of Characters
Network...

42
 / > < $ % +      are prohibited.
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote control.  See  2. PICTURE menu on page 52  and Projector on page 7 for details.
ii. To switch between input signals , click on your desired signal.
The Menu button can also be used to go back to previous OSD menus, exit and save menu...

43
ii. You can name the projector, keep track of its location and the person in charge of 
it.
iii. You can adjust the LAN Control Settings.
iv. Once set, access to the remote network operation on this projector has been 
password-protected.
v. Once set, access to the tools page has been password-protected.
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for the 
projector.
vi. Press Exit to go...