ViewSonic Projector PJD6351LS User Manual

							34
Go to the PICTURE > Color Temp. menu and press /.
The options available for color temperature* settings vary according to the signal type 
selected.
1.Cool: With the highest color temperature, Cool makes the image appear the most 
bluish white than other settings.
2.Neutral: Makes images appear bluish white.
3.Normal: Maintains normal colorings for white.
4.Warm: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be white for various purposes. One 
of the common methods of representing white color is known as the “color temperature”. A 
white color with a low color temperature appears to be reddish white. A white color with a 
high color temperature appears to have more blue in it.
Setting a preferred color temperature
1. Go to the PICTURE > Color Temp. menu.
2. Press / to select Cool, Neutral, Normal or Warm and press Enter.
3. Press / to highlight the item you want to change and adjust the values by 
pressing /
.
•Red Gain/Green Gain/Blue Gain: Adjusts the contrast levels of Red, Green, 
and Blue.
•Red Offset/Green Offset/Blue Offset: Adjusts the brightness levels of Red, 
Green, and Blue.
This function is only available when a PC input signal is selected.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color reproduction, should 
you require it.
If you have purchased a test disc which contains various color test patterns and can be used 
to test the color presentation on monitors, TVs, projectors, etc., you can project any image 
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1. Open the OSD menu and go to the PICTURE > Advanced > Color Management 
menu.
2. Press Enter and the Color Management page is displayed.
3. Highlight Primary Color and press / to select a color from among Red, Yellow, 
Green, Cyan, Blue, or Magenta.
4. Press   to highlight Hue and press / to select its range. Increase in the range 
will include colors consisted of more proportions of its two adjacent colors. 
						

							35
Please refer to the illustration to the right for 
how the colors relate to each other.
For example, if you select Red and set its 
range at 0, only pure red in the projected 
picture will be selected. Increasing its range 
will include red close to yellow and red close 
to magenta.
5. Press   to highlight Saturation and adjust 
its values to your preference by pressing /
. Every adjustment made will reflect to the 
image immediately.
For example, if you select Red and set its 
value at 0, only the saturation of pure red will 
be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less 
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation 
is too high, that color will be overpowering and unrealistic.
6. Press   to highlight Gain and adjust its values to your preference by pressing /. 
The contrast level of the primary color you select will be affected. Every adjustment 
made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press Exit to exit and save the settings.
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve 
better time management when giving presentations. Follow these steps to utilize this 
function:
1. Press   on the remote control to access the Presentation Timer menu or go to the 
SYSTEM SETTING: BASIC > Advanced > Presentation Timer menu.
2. Press Enter to display the Presentation Timer page.
3. Highlight Timer Period and decide the time period by pressing /. The length of 
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-
minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
4. Press   to highlight Timer Display and choose if you want the timer to show up on 
the screen by pressing
 /.
5. Press   to highlight Timer Position and set the timer position by pressing /.
RED
BLUEGREEN Yellow
Cyan
Magenta
SelectionDescription
AlwaysDisplays the timer on screen throughout the presentation 
time.
1 min/2 min/3 min  Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
Top-Left Bottom-Left Top-Right Bottom-Right 
						

							36
6. Press   to highlight Timer Counting Direction and select your desired counting 
direction by pressing /.
7. Press   to highlight Sound Reminder and decide if you want to activate sound 
reminder by pressing /. If you select On, a double beep sound will be heard at 
the last 30 seconds of counting down/up, and a triple beep sound will be produced 
when the timer is up.
8. To activate the presentation timer, press   and press / to highlight Start 
Counting and press Enter.
9. A confirmation message displays. Highlight Yes and press Enter to confirm. You will 
see the message “Timer is On” displaying on the screen. The timer starts counting 
when the timer is on.
To cancel the timer, perform the following steps:
1. Go to the SYSTEM SETTING: BASIC > Advanced > Presentation Timer menu.
2. Highlight Off. Press Enter. A confirmation message displays.
3. Highlight Yes and press Enter to confirm. You will see the message “Timer is Off” 
displaying on the screen.
Hiding the image
In order to draw the audiences full attention to the presenter, you can press BLANK to hide 
the screen image. Press any key on the projector or remote control to restore the image. The 
word BLANK appears at the lower right corner of the screen while the image is hidden.
You can set the blank time in the 
SYSTEM SETTING: BASIC > Blank Timer menu to 
let the projector return the image automatically after a period of time when there is no action 
taken on the blank screen. 
Once Blank is pressed, the projector enters Economic mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to 
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from 
being changed accidentally (by children, for example). When the Panel Key Lock is on, no 
control keys on the projector will operate except Power.
1. Press  (Panel Key Lock), or go to the 
SYSTEM SETTING: ADVANCED > 
Advanced > Panel Key Lock menu
2. Press / to select On.
3. A confirmation message is displayed. Select Yes to confirm.
To release panel key lock, press and hold   for 3 seconds.
You can also use the remote control to enter the 
SYSTEM SETTING: ADVANCED > 
Advanced > Panel Key Lock
 menu and press / to select Off.
SelectionDescription
Count UpIncreases from 0 to the preset time.
Count DownDecreases from the preset time to 0. 
						

							37
Keys on the remote control are still functional when panel key lock is enabled.
If you press  Power to turn off the projector without disabling panel key lock, the projector 
will still be in locked status the next time it is turned on.
Creating your own startup screen
In addition to selecting the projector preset startup screen from among Black, Blue, or 
ViewSonic screen, you can make your own startup screen that is a picture projected from 
your computer or video source.
To create your own startup screen: 
1. Project the picture you want to use as your startup screen from either a computer or 
video source.
2. Open the OSD menu and go to the SYSTEM SETTING: BASIC > Screen Capture 
menu.
3. Press Enter.
4. A confirmation message displays. Press Enter again.
5. The message Screen Capturing... displays while the projector is processing the 
picture. Please wait.
6. If the action is successful, you see the message Captured Succeeded on the screen.  
The captured picture is saved as Screen Capture and have been set as your current 
startup screen.
In the unlikely event that the capturing action fails, change your target picture. When the 
resolution of the input signal is higher than the projector’s native display resolution (See 
Projector specifications on page 64 for details.), the capture action may fail. When it 
happens, please set the resolution of the input signal under native resolution and try again.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500 
m–3000 m above sea level, and temperature is between 5°C–25°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature 
is between 5°C and 35°C. The projector will be over cooled, if you turn the mode on under 
such a condition.
To activate the High Altitude Mode:
1. Open the OSD menu and go to the SYSTEM 
SETTING: ADVANCED > High Altitude 
Mode menu.
2. Press / to select On. A confirmation 
message is displayed.
3. Highlight Yes and press Enter.
Operation under High Altitude Mode may cause a 
higher decibel operating noise level because of increased fan speed necessary to improve 
overall system cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display 
auto shut-down symptoms, which is designed to protect your projector from over-heating. 
In cases like this, you should switch to High Altitude Mode to solve these symptoms. 
However, this is not to state that this projector can operate under any and all harsh or 
extreme conditions.
We recommend you use the High Altitude 
mode by selecting it whenever your 
environment is higher than 1500 m.
YesNoNotice
Do you want to turn High Altitude 
Mode ON? 
						

							38
Using the CEC function
This projector supports CEC (Consumer Electronics Control) function for synchronized 
power on/off operation via HDMI connection. That is, if a device that also supports CEC 
function is connected to the HDMI input of the projector, when the projector’s power is 
turned off, the power of the connected device will also be turned off automatically. When 
the power of the connected device is turned on, the projector’s power will be turned on 
automatically.
To turn on the CEC function:
1. Open the OSD menu and go to the SOURCE > Auto Power On > CEC menu.
2. Press / to select Enable.
In order for the CEC function to work properly, make sure that the device is correctly 
connected to the HDMI input of the projector via an HDMI cable, and its CEC function is turned 
on.
Depending on the connected device, the CEC function may not work.
Using the 3D functions
This projector features 3D function which enables you to enjoy 3D movies, videos, and 
sporting events in a more realistic way by presenting the depth of the images. You need to 
wear a pair of 3D glasses to view 3D images.
If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects the 
signal for 3D Sync information and once detected, it projects images in 3D format 
automatically. In other cases, you may need to manually select a 3D Sync format for the 
projector to project 3D images correctly.
To select a 3D Sync format:
1. Press 3D on the remote control to access the 3D Settings menu or go to the 
SOURCE > 3D Settings menu.
2. Press Enter. The 3D Settings page is displayed.
3. Highlight 3D Sync and press Enter.
4. Press 
 to select a 3D Sync setting and then press Enter to confirm.
When the 3D Sync function is on:
• The brightness level of the projected image will decrease.
• The Color Mode cannot be adjusted.
• The Zoom function can only magnify the pictures to limited sizes.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert” 
to correct the problem. 
						

							39
Controlling the projector through a LAN 
environment
The projector supports Crestron® software. With correct settings for the LAN Control 
Settings menu, you can manage the projector from a computer using a web browser when 
the computer and the projector are properly connected to the same local area network. 
Configuring the LAN Control Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector 
and the other end to the RJ45 port.
2. Open the OSD menu and go to the SOURCE >  LAN Control Settings menu.
3. Press Enter. The LAN Control Settings page is displayed.
4. Highlight LAN Control Settings and press  /  to select DHCP ON.
5. Press   to highlight Apply and press Enter.
6. Please wait for around 15 - 20 seconds, and then re-enter the LAN Control Settings 
page. The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server 
settings will be displayed. Note down the IP address displayed in the Projector IP 
Address row.
If the Projector IP Address still does not appear, contact your network administrator.
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default 
Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are properly 
connected and perform the procedures above again.
If you need to connect to the projector in its standby mode, set LAN Control to On in the 
SOURCE > Standby Settings menu.
If you are in a non-DHCP environment:
1. Repeat steps 1-3 above.
2. Highlight LAN Control Settings and press  /  to select Static IP.
3. Contact your ITS administrator for information on the Projector IP Address, Subnet 
Mask, Default Gateway, and DNS Server settings.
4. Press   to select the item you want to modify and press Enter.
5. Press  /  to move the cursor and the press / to enter the value.
6. To save the settings, press Enter. If you do not want to save the settings, press Exit.
7. Press   to highlight Apply and press Enter.
(An example of connection) 
						

							40
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default 
Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are properly 
connected and perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have selected 
Static 
IP and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server 
information when the projector is on.
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby 
mode, you can use any computer that is on the same local area network to control the 
projector.
If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
The screen shots in this manual are for reference only, and may differ from the actual design.
1. Enter the address of the projector in the address bar of your browser and press Enter.
2. The main page of the Network Control appears.
Accessing to Network Settings or Email Alert page requires Administrator password. The 
default password is 0000.
3. This page allows you to make adjustments to the AMX and SNMP settings.  In the 
AMX device discover row, when ON is selected, the projector can be detected by 
controllers of AMX connected to the same network. For the Details of AMX Device 
Discovery, visit the AMX web site at http://www.amx.com/.
5
4
3 
						

							41
4. If your projector is connected to a network which supports Simple Mail Transfer 
Protocol (SMTP), you can configure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See 
About Crestron e-Control® on page 42 for details. 
Please pay attention to the limitation of input length (including space and other punctuation 
keys) in the list blow:
Category ItemInput LengthMaximum Number 
of Characters
Network SettingsNetworkDHCP/Manual (N/A)
IP Address XXX.XXX.XXX.XXX
Subnet Mask XXX.XXX.XXX.XXX
Gateway XXX.XXX.XXX.XXX
DNS Server XXX.XXX.XXX.XXX
AMX device discovery (N/A)
PasswordAdministrator (N/A)
New Password 4
Confirm Password 4
SNMPSysLocation 22
SysName 22
SysContact 22
Email AlertEmail SettingTo 4 0
Cc 40
Subject 40
From 40
SMTP SettingServer 30
User Name 21
Password 14
Alert ConditionFan Error (N/A)
Lamp Error (N/A)
Over Temperature (N/A)
Lamp Time Alert (N/A)
Submit (N/A)
Issue Test Mail (N/A) 
						

							42
 / > < $ % +      are prohibited.
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote control.  See  2. PICTURE menu on page 52  and Projector on page 7 for details.
ii. To switch between input signals , click on your desired signal.
The Menu button can also be used to go back to previous OSD menus, exit and save menu 
settings.
The source list varies according to the connectors available on the projector.
When you use the projector control panel or re mote control to change the OSD menu settings, 
it may take a while for the web browser to  synchronize these changes with the projector.
2. The tools page allows you to manage the projector, configure the LAN control 
settings and secure access of remote network operation on this projector.
i. This section is only used with the  Crestron Control System. Please contact 
Creston or refer to its user  manual for setup information.
i
i
i
ii
You can press / to 
reveal more 
buttons.
iiv
iii
ii
v
vi 
						

							43
ii. You can name the projector, keep track of its location and the person in charge of 
it.
iii. You can adjust the LAN Control Settings.
iv. Once set, access to the remote network operation on this projector has been 
password-protected.
v. Once set, access to the tools page has been password-protected.
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for the 
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limitation of input length (including space and other punctuation 
keys) in the list blow:
Category ItemInput LengthMaximum Number of 
Characters
Crestron ControlIP Address 16
IP ID 4
Port 5
ProjectorProjector Name 32
Location 32
Assigned To 32
Network ConfigurationDHCP (Enabled) (N/A)
IP Address 16
Subnet Mask 16
Default Gateway 16
DNS Server 16
User PasswordEnabled (N/A)
New Password 26
Confirm 26
Admin PasswordEnabled (N/A)
New Password 26
Confirm 26