ViewSonic Projector PJD6350 User Manual

							44
3. The info page displays the information and status of this projector.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in 
the upper right corner of the screen. You will be able to deliver messages to 
RoomView™ software administrators/users who connect to the same local area 
network.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview. 
**Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s 
on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved Crestron 
control port.
About Crestron RoomView™ setting and command method, please access below website to 
get RoomView™ User Guide and more information: 
http://www.crestron.com/products/roomview_connected_embedded_projectors_devices/
resources.asp
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, 
please follow its user guide or website respectively to control and manage projectors.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned 
on). To use these functions, be sure you have turned on the corresponding menus under 
SOURCE > Standby Settings, and the cable connections are correctly made. For the 
connection methods, see the Connection chapter.
Press Exit to 
go back to the 
remote network 
operation page. 
						

							45
Active VGA Out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT 
sockets are correctly connected to devices. The projector outputs the signal received only 
from COMPUTER IN 1. 
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN 1 socket is correctly connected 
to a proper device.
LAN Control
Selecting On allows the projector to provide the network function when it is in standby 
mode. See Controlling the projector through a LAN environment on page 39 for details.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker. Be sure 
you have made a correct connection to the projector audio input/output jacks. See 
Connection on page 15 for more details.
Adjusting the audio mode
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Audio Mode menu.
2. Press  /  to select a preferred audio mode.
If available, you can press Audio Mode on the remote control to select a preferred audio mode.
Muting the sound
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Mute menu.
2. Press / to select On.
If available, you can press   on the remote control to toggle the projector audio between on 
and off.
Adjusting the sound level
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Audio Volume menu.
2. Press / to select a desired sound level.
If available, you can press  on the remote control to adjust the projector’s sound level. 
						

							46
Adjusting the Audio In 2 setting
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Audio In 2 menu. 
2. Press  /  to decide the audio input source for the AUDIO IN 2/MIC port. This 
will affect the connection method for different devices, and where the sound is from.
• When Audio is selected:
The selected input signal determines which sound will be played by the projector speaker, and 
which sound will be output from the projector when AUDIO OUT is connected. For instance, if 
you select a D-Sub / Comp. 1 source, the projector can play the sound received from AUDIO IN 
1.
• When Microphone is selected:
Adjusting the microphone sound level
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Microphone Volume menu.
2. Press / to select a desired sound level.
This function is only available when the SYSTEM SETTING: ADVANCED > Audio Settings > 
Audio In 2 menu is set to Microphone.
Turning off the Power On/Off Ring Tone
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Power On/Off Ring Tone menu.
2. Press / to select Off.
The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound 
mute or changing the sound level will not affect the Power On/Off Ring Tone.
Device COMPUTER IN 1 COMPUTER IN 2 Video/S-Video
Audio input portAUDIO IN 1 AUDIO IN 2 AUDIO IN 2
The projector can play 
the sound from...AUDIO IN 1 AUDIO IN 2 AUDIO IN 2
Audio output portAUDIO OUT AUDIO OUT AUDIO OUT
DeviceCOMPUTER IN 1 COMPUTER IN 2 Video/S-Video
Audio input portAUDIO IN 1 AUDIO IN 1 AUDIO IN 1
The projector can play 
the sound from...• AUDIO IN 1
•MIC• AUDIO IN 1
•MIC• AUDIO IN 1
•MIC
Audio output portAUDIO OUT AUDIO OUT AUDIO OUT 
						

							47
Shutting down the projector
1. Press Power and a confirmation message is 
displayed prompting you. 
If you dont respond in a few seconds, the 
message will disappear.
2. Press Power a second time.
3. Once the cooling process finishes, a Power 
Off Ring Tone will be heard. Disconnect the 
power cord from the wall socket if the 
projector will not be used in an extended 
period of time.
To turn off the ring tone, see Turning off the Power On/Off Ring Tone on page 46 for details.
CAUTION
• To protect the lamp, the projector will not respond to any commands during the cooling 
process.
• To shorten the cooling time, you can also activate the Quick Power Off function. See 
Quick Power Off on page 53 for details.
• Do not unplug the power cord before the projector shutdown sequence is complete. 
						

							48
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
The menu items are available when the projector detects at least one valid signal. If there is 
no equipment connected to the projector or no signal detected, limited menu items are 
accessible.
Main menu Sub-menu Options
1. 
DISPLAY
Screen Color Off/Blackboard/Greenboard/Whiteboard
Aspect RatioAuto/4:3/16:9/16:10 (PJD6550Lw/
PJD6551Lws/PJD6552Lw/PJD6552Lws)/
Wide (PJD6550Lw/PJD6551Lws/
PJD6552Lw/PJD6552Lws)/Panorama 
(PJD6350/PJD6351Ls/PJD6352/
PJD6352Ls)/2.35:1/Anamorphic
Keystone
Corner Adj.
Position
Phase
H. Size
Zoom
2. 
PICTURE
Color Mode Brightest/Dynamic/Standard/ViewMatch/Movie
Brightness
Contrast
Color Temp.Warm
Red Gain/Green Gain/
Blue Gain/Red Offset/
Green Offset/Blue Offset Normal
Neutral
Cool
OverScan Off/1/2/3/4/5
HDMI 
SettingsHDMI Format Auto/RGB/YUV
HDMI Range Auto/Enhanced/Normal
AdvancedColor
Tint
Sharpness
Gamma 1/2/3/4/5/6/7/8
Brilliant Color Off/1/2/3/4/5/6/7/8/9/10
Noise Reduction
Color 
ManagementPrimary Color
Hue
Saturation
Gain
Reset Color Settings Reset/Cancel 
						

							49
Main menu Sub-menu Options
3. SOURCE
Quick Auto Search Off/On
3D Settings3D SyncAuto/Off/Frame Sequential/
Frame Packing/Top-Bottom/
Side-by-Side
3D Sync Invert Disable/Invert
Standby 
SettingsActive VGA Out Off/On
Active Audio Out Off/On
LAN Control Off/On
Auto Power OnComputer Disable/Enable
CEC Disable/Enable
Direct Power On Off/On
Auto Power OffPower Saving Disable/10 min/20 min/30 min
Sleep TimerDisable/30 min/1 hr /2 hr/3 hr/
4 hr/8 hr/12 hr
Smart Restart Disable/Enable
Quick Power Off Disable/Enable
LAN Control 
SettingsLAN Control 
SettingsDHCP ON/Static IP
Projector IP Address
Subnet Mask
Default Gateway
DNS Server
Apply
4. 
SYSTEM 
SETTING: 
BASIC
LanguageMulti-language OSD 
selection
Projector PositionFront Table/Rear Table/
Rear Ceiling/Front Ceiling
Menu SettingsMenu Display Time5 sec/10 sec/15 sec/20 sec/
25 sec/30 sec
Menu PositionCenter/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Blank TimerDisable/5 min/10 min/15 min/
20 min/25 min/30 min
Splash ScreenBlack/Blue/ViewSonic/
Screen Capture/Off
Screen Capture
My ButtonAuto/Projection (Projector Position)/Menu 
Position/Color Temp./Brightness/Contrast/3D 
Settings/Screen Color/Splash Screen/Message/
Quick Auto Search/CEC/Audio Mode/Lamp Mode/
DCR/Closed Caption/Power Saving/Freeze/
INFORMATION 
						

							50
Main menu Sub-menu Options
4. 
SYSTEM 
SETTING: 
BASIC
AdvancedPattern Off/1/2/3
Message On/Off
Presentation TimerTimer Period
Timer Display
Timer Position
Timer Counting 
Direction
Sound Reminder
Start Counting/Off
5. 
SYSTEM 
SETTING: 
ADVANCED
High Altitude Mode On/Off
DCR On/Off
Audio SettingsAudio ModeStandard/Speech/
Entertainment
Mute On/Off
Audio Volume
Audio In 2 Audio/Microphone
Microphone Volume
Power On/Off Ring 
ToneOn/Off
Closed Caption Off/CC1/CC2/CC3/CC4
Lamp SettingsLamp ModeNormal/Economic/
Dynamic/Sleep Mode
Reset Lamp Hours
Lamp Hours
Filter SettingsFilter Mode On/Off
Reset Filter Hours
Filter Hours
Remote Control Code 1/2/3/4/5/6/7/8 (All)
AdvancedSecurity SettingsChange Password
Power On Lock
Panel Key Lock Off/On
Reset Settings Reset/Cancel
6. 
INFORMATIONCurrent System Status•Source
•Color Mode
•Resolution
•Color System
•Lamp Hours
• Filter Hours
•IP Address
•MAC Address
•Firmware Version 
						

							51
Description of each menu
FunctionDescription
Screen ColorSee 
Using Screen Color on page 32  for details.This function is only available when a PC input signal is 
selected.
Aspect RatioSee Selecting the aspect ratio on page 30  for details.
Keystone See Correcting keystone on page 29  for details.
Corner Adj. See Adjusting 4 corners on page 29  for details.
Position Displays the position adjustment
 page. To move the projected 
image, use the directional arrow keys. The values shown on the 
lower position of the page change with every key press you made 
until they reach their maximum or minimum.
This function is only available when a PC input signal is 
selected.
The adjustment range may va ry under different timings.
PhaseAdjusts the clock phase to reduce image 
distortion.
This function is only available when 
a PC input signal is selected.
H. Size
Adjusts the horizontal width of the image.This function is only available when a PC input signal is 
selected.
Zoom
See 
Magnifying and searching for details on page 30  for 
details.
Color Mode See Selecting a picture mode on page 32  for details.
Brightness See Adjusting Brightness on page 33  for details.
Contrast See Adjusting Cont rast on page 33 for details.
Color Temp. See 
Selecting a Color Temperature on page 33  and Setting a 
preferred color temperature on page 34  for details.
OverScan Adjusts the overscan rate from 0% to 5%.
This function is only available when a Composite Video, 
S-Video or HDMI input signal is selected.
HDMI Settings
See Changing HDMI input settings on page 27  for details.
1. DISPLAY menu
2. PICTURE menu 
						

							52
Function Description
AdvancedColor
See Adjusting Color on page 33 for details.
Tint
See Adjusting Tint on page 33 for details.
The function is only available when Video or S-Video 
input with NTSC system is selected.
Sharpness
See Adjusting Sharpness on page 33 for details.
Gamma
See Selecting a gamma setting on page 33 for details.
Brilliant Color
See Adjusting Brilliant Color on page 33 for details.
Noise Reduction
See Reducing image noise on page 33 for details.
Color Management
See Color Management on page 34 for details.
Reset Color 
SettingsReturns all color settings to the factory preset values.
Quick Auto 
SearchSee Switching input signal on page 27 for details.
3D SettingsSee Using the 3D functions on page 38 for details.
Standby 
SettingsSee Using the projector in standby mode on page 44 for 
details.
Auto Power OnComputer
Selecting Enable allows the projector to turn on automatically 
once the VGA signal is fed through the VGA cable.
CEC
See Using the CEC function on page 38 for details.
Direct Power On
Selecting On allows the projector to turn on automatically 
once the power is fed through the power cord.
2. PICTURE menu
3. SOURCE menu 
						

							53
Function Description
Auto Power OffPower Saving
See Setting Power Saving on page 59 for details.
Sleep Timer
See Setting Sleep Timer on page 59 for details.
Smart RestartSelecting Enable enables you to restart the projector 
immediately within 120 seconds after turning it off. After 120 
seconds, if the projector is not turned on again, it will directly 
enter the standby mode.
It takes some time to initiate this function. Make sure 
the projector has been turned on for more than 4 
minutes. If the projector is resumed by using the Smart 
Restart feature, this function can be executed 
immediately. 
When Enable is selected, the Quick Power Off function 
will be automatically set to “Enable”.
Quick Power 
OffSelecting Enable enables the function and the projector will 
not enter the cooling process after being shut down. Selecting 
Disable disables the function and the projector will enter 
normal cooling process after being shut down.If you attempt to restart the projector right after it’s been 
turned off, it may not be turned on successfully and will 
rerun its cooling procedure.
When Disable is selected, the Smart Restart function 
will be automatically turned off.
LanguageSets the language for the On-Screen Display (OSD) menus. 
See Using the menus on page 24 for details.
Projector 
PositionSee Choosing a location on page 12 for details.
Menu SettingsMenu Display Time
Sets the length of time the OSD will remain active after your 
last key press. The range is from 5 to 30 seconds in 5-second 
increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Blank TimerSee Hiding the image on page 36 for details.
3. SOURCE menu
4. SYSTEM SETTING: BASIC menu