ViewSonic Projector PJD6350 User Manual

							PJD6350/PJD6351LS/PJD6352/
PJD6352LS/PJD6550LW/
PJD6551LWS/PJD6552LW/
PJD6552LWS
DLP Projector
User Guide
Model No.
VS15877/VS15878/VS15947/VS15948/VS15879/
VS15880/VS15949/VS15950
IMPORTANT:  Please read this User Guide to obtain important information on installing 
and using your product in a safe manner, as well as registering your product for future 
service.  Warranty information contained in this User Guide will describe your limited 
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com  in  English,  or  in  specific  languages  using  the  Regional  selection 
box in the upper right corner of our website. “Antes de operar su equ\
ipo lea cu 
idadosamente las instrucciones en este manual” 
						

							Thank you for choosing ViewSonic
With over 25 years as a world leading provider of visual solutions,  
ViewSonic is dedicated to exceeding the world’s expectations for 
technological evolution, innovation, and simplicity. At ViewSonic, we 
believe that our products have the potential to make a positive impact 
in the world, and we are confident that the ViewSonic product you have 
chosen will serve you well. 
Once again, thank you for choosing ViewSonic !  
						

							i
Compliance Information
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to \
the following 
two conditions: (1) this device may not cause harmful interference, an\
d (2) this 
device must accept any interference received, including interference tha\
t may cause 
undesired operation.
This equipment has been tested and found to comply with the limits for a\
 Class 
B digital device, pursuant to part 15 of the FCC Rules. These limits are\
 designed 
to provide reasonable protection against harmful interference in a resid\
ential 
installation. This equipment generates, uses, and can radiate radio freq\
uency 
energy, and if not installed and used in accordance with the instruction\
s, may cause 
harmful interference to radio communications. However, there is no guara\
ntee that 
interference will not occur in a particular installation. If this equipm\
ent does cause 
harmful interference to radio or television reception, which can be dete\
rmined 
by turning the equipment off and on, the user is encouraged to try to co\
rrect the 
interference by one or more of the following measures:•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to\
 which the 
receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
Warning:  You are cautioned that changes or modifications not expressly approved \
by the party responsible for compliance could void your authority to ope\
rate the 
equipment.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage 
Directive 2006/95/EC.
Following information is only for EU-member states: 
The mark is in compliance with the Waste Electrical and Electronic 
Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment 
including any spent or discarded batteries or accumulators as unsorted 
municipal waste, but use the return and collection systems available. 
If the batteries, accumulators and button cells included with this equip\
ment, 
display the chemical symbol Hg, Cd, or Pb, then it means that the batter\
y 
has a heavy metal content of more than 0.0005% Mercury or more than, 
0.002% Cadmium, or more than 0.004% Lead.  
						

							ii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Direc\
tive 
2011/65/EU of the European Parliament and the Council on restriction of \
the use 
of certain hazardous substances in electrical and electronic equipment (\
RoHS2 
Directive) and is deemed to comply with the maximum concentration value\
s issued 
by the European Technical Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum 
ConcentrationActual Concentration
Lead (Pb)0.1%< 0.1%
Mercury (Hg) 0.1%< 0.1%
Cadmium (Cd) 0.01%< 0.01%
Hexavalent Chromium (Cr
6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1%< 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1%< 0.1%
Certain components of products as stated above are exempted under the Annex III 
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent 
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length ( ＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length ( ＞1,500 mm): maximum 13 mg per lamp.
2.  Lead in glass of cathode ray tubes.
3.  Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
4.  Lead as an alloying element in aluminium containing up to 0.4% lead by w\
eight.
5.  Copper alloy containing up to 4% lead by weight.
6.  Lead in high melting temperature type solders (i.e. lead-based alloys c\
ontaining 
85% by weight or more lead).
7.  Electrical and electronic components containing lead in a glass or ceram\
ic other 
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or \
in a glass or 
ceramic matrix compound.
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India) This product com\
plies 
with the “India E-waste Rule 2011” and prohibits use of lead, merc\
ury, hexavalent 
chromium, polybrominated biphenyls or polybrominated diphenyl ethers in \
concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, exc\
ept for 
the exemptions set in Schedule 2 of the Rule.  
						

							iii
Important Safety Instructions
1. Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this unit near water.
6.  Clean with a soft, dry cloth.
7.  Do not block any ventilation openings. Install the unit in accordance wi\
th the 
manufacturer’s instructions.
8.  Do not install near any heat sources such as radiators, heat registers, \
stoves,   
or other devices (including amplifiers) that produce heat.
9.  Do not defeat the safety purpose of the polarized or grounding-type plug\
. A   
polarized plug has two blades with one wider than the other. A grounding\
 type 
plug has two blades and a third grounding prong. The wide blade and the \
third 
prong are provided for your safety. If the provided plug does not fit in\
to your   
outlet, consult an electrician for replacement of the obsolete outlet.
10.  Protect the power cord from being walked on or pinched particularly at p\
lugs. 
Convenience receptacles and the point where they exit from the unit. Be \
sure 
that the power outlet is located near the unit so that it is easily acce\
ssible.
11.  Only use attachments/accessories specified by the manufacturer.
12.  Use only with the cart, stand, tripod, bracket, or table specified by th\
e 
manufacturer, or sold with the unit. When a cart is used, use caution 
when moving the cart/unit combination to avoid injury from tipping 
over.
13.  Unplug this unit when unused for long periods of time.
14.  Refer all servicing to qualified service personnel. Servicing is require\
d when the 
unit has been damaged in any way, such as: if the power-supply cord or p\
lug is 
damaged, if liquid is spilled onto or objects fall into the unit, if the\
 unit is exposed 
to rain or moisture, or if the unit does not operate normally or has bee\
n dropped.  
						

							iv
Copyright Information
Copyright © ViewSonic Corporation, 2015. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Mi\
crosoft 
Corporation in the United States and other countries.
ViewSonic and the three birds logo are registered trademarks of ViewSoni\
c 
Corporation.
VESA is a registered trademark of the Video Electronics Standards Associ\
ation. 
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Ma\
chines 
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or e\
ditorial errors 
or omissions contained herein; nor for incidental or consequential damag\
es resulting 
from furnishing this material, or the performance or use of this product\
.
In the interest of continuing product improvement, ViewSonic Corporation\
 reserves 
the right to change product spec ifications without notice. Information in this 
document may change without notice.
No part of this document may be copied, reproduced, or transmitted by an\
y means, 
for any purpose without prior written permission from ViewSonic Corporat\
ion.  
						

							v
Product Registration
To fulfill possible future product needs, and to receive additional prod\
uct information 
as it becomes available, please visit your region section on ViewSonic’\
s website to 
register your product online.
The ViewSonic CD also provides an opportunity for you to print the produ\
ct 
registration form. Upon completion, please mail or fax to a respective V\
iewSonic 
office. To find your registration form, use the directory “:\CD\Reg\
istration”. 
Registering your product will best prepare you for future customer servi\
ce needs.
Please print this user guide and fill the information in the “For You\
r Records” section. 
For additional information, please see the “Customer Support” sect\
ion in this guide.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:PJD6350/PJD6351LS/PJD6352/PJD6352LS/
PJD6550LW/PJD6551LWS/PJD6552LW/
PJD6552LWS
ViewSonic DLP Projector
VS15877/VS15878/VS15947/VS15948/VS15879/
VS15880/VS15949/VS15950
PJD6350/PJD6351LS/PJD6352/PJD6352LS/
PJD6550LW/PJD6551LWS/PJD6552LW/
PJD6552LWS_UG_ENG Rev. 1A 12-31-14
 
 
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you \
and the 
environment. Please use care and dispose of in accordance with local, st\
ate or   
federal laws.
ViewSonic respects the environment and is committed to working and livin\
g green. 
Thank you for being part of Smarter, Greener Computing.
Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/\
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx  
						

							1
Table of contents
Important safety 
instructions .......................2
Introduction ......................4
Projector features ................................. 4
Shipping contents ................................. 5
Projector exterior view ......................... 6
Controls and functions ......................... 7
Positioning your 
projector..........................12
Choosing a location............................ 12
Projection dimensions ........................ 13
Connection ......................17
Connecting a computer or monitor .... 18
Connecting Video source devices ...... 19
Playing sound through the projector .. 21
Using the cable management cover ... 22
Operation ........................23
Starting up the projector..................... 23
Using the menus................................. 24
Utilizing the password function ......... 25
Switching input signal........................ 27
Adjusting the projected image ........... 28
Magnifying and searching for details. 30
Selecting the aspect ratio ................... 30
Optimizing the image......................... 32
Setting the presentation timer ............ 35
Hiding the image ................................ 36
Locking control keys.......................... 36
Creating your own startup screen....... 37
Operating in a high altitude 
environment ....................................... 37Using the CEC function..................... 38
Using the 3D functions ...................... 38
Controlling the projector through 
a LAN environment ........................... 39
Using the projector in standby mode . 44
Adjusting the sound ........................... 45
Shutting down the projector .............. 47
Menu operation .................................. 48
Maintenance ...................57
Care of the projector .......................... 57
Using the dust filter (optional 
accessory) .......................................... 57
Lamp information .............................. 59
Troubleshooting .............63
Specifications..................64
Projector specifications...................... 64
Dimensions ........................................ 66
Ceiling mount installation ................. 66
Timing chart ...................................... 67
Copyright information...71
Appendix .........................72
IR control table .................................. 72
RS232 command table ....................... 73 
						

							2
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information 
technology equipment. However, to ensure safe use of this product, it is important that you 
follow the instructions mentioned in this manual and marked on the product. 
Safety Instructions
1.Please read this manual before you operate your projector. Save it for future 
reference.
2.Do not look straight at the projector lens during operation. The intense light beam 
may damage your eyes.
3.Refer servicing to qualified service personnel. 
4.Always open the lens shutter or remove the lens cap when the projector lamp is 
on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate 
safely within a mains voltage between 100 to 240 volts AC, but could fail if power 
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate 
or cut out, it is recommended that you connect your projector through a power 
stabilizer, surge protector or uninterruptible power supply (UPS). 
6. Do not block the projection lens with any objects when the projector is under 
operation as this could cause the objects to become heated and deformed or even 
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or 
remote control.
7. The lamp becomes extremely hot during operation. Allow the projector to cool for 
approximately 45 minutes prior to removing the lamp assembly for replacement. 
8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps 
beyond the rated life could cause them to break on rare occasions. 
9. Never replace the lamp assembly or any electronic components unless the projector is 
unplugged. 
10. Do not place this product on an unstable cart, stand, or table. The product may fall, 
sustaining serious damage. 
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside 
which may cause death if you should come into contact with live parts. The only user 
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer 
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments. 
-  Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls 
and free flow of air around the projector.
-  Locations where temperatures may become excessively high, such as the inside of a 
car with all windows rolled up.
-  Locations where excessive humidity, dust, or cigarette smoke may contaminate optical 
components, shortening the projectors life span and darkening the picture.
-  Locations near fire alarms
-  Locations with an ambient temperature above 40°C / 104°F
-  Locations where the altitudes are higher than 3000 m (10000 feet). 
						

							3
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, 
overheating inside the projector may result in a fire.
-  Do not place this projector on a blanket, bedding or any other soft surface. 
-  Do not cover this projector with a cloth or any other item. 
-  Do not place inflammables near the projector.   
14. Always place the projector on a level, horizontal surface during operation.
-  Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of 
more than 15 degrees front to back. Using the projector when it is not fully horizontal 
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall 
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical 
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may 
cause it to fail. If the projector does become wet, disconnect it from the power 
supplys wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation. 
Use only qualified ceiling mount kit for mounting the projector and ensure it is 
securely installed. 
19. When the projector is under operation, you may sense some heated air and odor from 
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a 
commercially available theft prevention cable. 
Safety instructions for ceiling mounting of the 
projector
We want you to have a pleasant experience using your projector, so we need to bring this 
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a 
proper fitting projector ceiling mount kit and that you ensure it is securely and safely 
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the 
projector may fall from the ceiling due to an improper attachment through the use of the 
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector. 
We recommend that you also purchase a separate security cable and attach it securely to 
both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This 
will perform the secondary role of restraining the projector should its attachment to the 
mounting bracket become loose.