ViewSonic Projector PJD6252L User Manual

26
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only 
display one full screen at a time. 
Be sure the  Quick Auto Search  function in the SOURCE menu is  On if you want the 
projector to automatically search for the signals.
You can also manually select the desired signal by 
pressing one of the source selection keys on the 
remote control, or cycle through the available input 
signals.
1. Press  Source. A source selection bar is 
displayed....

27
•Normal : Sets the HDMI color range as 15 - 235.
• Auto: Sets the projector to detect th e HDMI range of the input signal 
automatically.
This function is only available when the HDMI input port is in use.
Refer to the documentation of the device for information on the color space and HDMI range 
settings.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with an adjuster foot. It 
changes the image height and vertical projection 
angle. Screw the adjuster foot to...

28
Correcting keystone
Keystoning refers to the situation where the projected image becomes a trapezoid due to 
angled projection.
To correct this, besides adjust ing the height of the projector, you will need to manually 
correct it following one of these steps.
• Using the remote control
1. Press  /// to display the Keystone 
correction page. 
2. Press   to correct keystoning at the top of  the image. Press   to  correct keystoning at 
the bottom of the image. Press   to correct 
keystoning at the...

29
Adjusting 4 corners (PJD7326/PJD7526W)
You can manually adjusts the shape and size of  an image that is unevenly rectangular on all 
sides. 
1. To display the  Corner Adj. page, you can do 
one of the followings:
i. Press  Enter. 
ii. Open the OSD menu and go to the 
DISPLAY > Corner Adj.  menu and 
press  Enter . The Corner Adj.  page is 
displayed.
2. Press  / / /  to select the corner you  wish to adjust and press  Enter.
3. Press  / to select an adjustment method 
that suits your need and press...

30
4. To reduce size of the picture, press Enter to switch back to the zoom in/out 
functionality, and press   repeatedly until it  is restored to the original size. You can 
also press  Auto Sync  on the remote control to restore the picture to its original size.
• Using the OSD menu
1. Open the OSD menu and go to the 
DISPLAY > Zoom menu. 
2. Press  Enter. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of Using the remote control above.
This adjustable range may vary depending on...

31
4.16:10 (PJD6551W/PJD7526W): Scales an 
image so that it is disp layed in the center of the 
screen with a 16:10 aspect  ratio. This is most 
suitable for images which are already in a 16:10 
aspect, as it displays them without aspect 
alteration.
5. Panorama  (PJD6551W/PJD7526W/
PJD7720HD): Scales a 4:3 image vertically and 
horizontally in a non-linear manner so that it 
fills the screen.
6. 2.35:1: Scales an image so that it is displayed in 
the center of the screen with a 2.35:1 aspect 
ratio...

32
3.Standard mode: Is designed for presentations unde r daylight environment to match 
PC and notebook coloring.
4. ViewMatch sRGB mode : Switches between high br ightness performance and 
accurate color performance.
5. Movie mode : Is appropriate for playing colorf ul movies, video clips from digital 
cameras or DVs through the PC input for best  viewing in a blackened (little light) 
environment. 
6. DICO
M SIM mode (PJD7326/PJD7526W) : Re
 commended for DICOM format files 
in simulation mode.
DICOM...

33
This function is only available when the input signal is S-Video, Video, YPbPr (digital) or 
YCbCr (digital).
Adjusting Tint
Go to the  PICTURE  > Advanced  > Tint menu and press  /.
The higher the value, the more reddish the pict ure becomes. The lower the value, the more 
greenish the picture becomes.
This function is only available when the input signal is S-Video, Vide o, YPbPr (digital) or 
YCbCr (digital).
Adjusting Sharpness
Go to the  PICTURE  > Advanced  > Sharpness  menu and press  /.
The...

34
2. Press / to select  Cool, Neutral , Normal  or Warm  and press  Enter.
3. Press  / to highlight the item you want to change and adjust the values by 
pressing  /
.
•Red Gain /Green Gain /Blue Gain : Adjusts the contrast le vels of Red, Green, 
and Blue.
• Red Offset /Green Offset /Blue Offset : Adjusts the brightness levels of Red, 
Green, and Blue.
This function is only  available when a PC input signal is selected.
Color Management
Only in permanent installations with controlled  lighting levels...

35
9. Press Exit to exit and save the settings.
Setting the presentation timer
Presentation timer can indicate the presentation  time on the screen to help you achieve 
better time management when giving presenta tions. Follow these steps to utilize this 
function:
• Using the remote control
1. Press   on the remote control and press   repeatedly or  /  to select a  Timer 
Period.
2. Press  Enter or wait for 3 seconds to activate the timer.
3. To display the  Presentation Timer  page, select Advanced.
•...