ViewSonic Projector PJD6252L User Manual

							PJD6252L/PJD6551W/PJD7326/
PJD7526W/PJD7720HD
DLP Projector
User Guide
Model No. VS16443/VS15913/VS16444/VS16445/VS16483 
IMPORTANT: Please read this User Guide to obtain important information on install\
ing 
and using your product in a safe manner, as well as registering your product for future 
service.  Warranty information contained in this User Guide will describe your limi\
ted 
coverage from ViewSonic Corporation, which is also found on our web site at http://
ZZZYLHZVRQLFFRP LQ (QJOLVK RU LQ VSHFL
						

							i
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to \
the follow-
ing two conditions: (1) this device may not cause harmful interference\
, and (2) this 
device must accept any interference received, including interference tha\
t may cause 
undesired operation.
This equipment has been tested and found to comply with the limits for a\
 Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a resident\
ial installa-
tion. This equipment generates, uses, and can radiate radio frequency energy, and 
if not installed and used in accordance with the instructions, may cause\
 harmful 
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does\
 cause harmful 
interference to radio or television reception, which can be determined b\
y turning the 
equipment off and on, the user is encouraged to try to correct the interference by o\
ne 
or more of the following measures:
 
yReorient or relocate the receiving antenna.
 
yIncrease the separation between the equipment and receiver.
 
yConnect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
 
yConsult the dealer or an experienced radio/TV technician for help.
Warning: 
						

							ii
Important Safety Instructions
1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this unit near water.
6.  Clean with a soft, dry cloth.
7.  Do not block any ventilation openings. Install the unit in accordance wi\
th the manufacturer’s instructions.
8.  Do not install near any heat sources such as radiators, heat registers, \
stoves,   RURWKHUGHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW
9.  Do not defeat the safety purpose of the polarized or grounding-type plug\
. A   polarized plug has two blades with one wider than the other. A grounding type 
plug has two blades and a third grounding prong. The wide blade and the third 
SURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW
						

							iii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Direc\
tive 
2011/65/EU of the European Parliament and the Council on restriction of \
the use 
of certain hazardous substances in electrical and electronic equipment (\
RoHS2 
Directive) and is deemed to comply with the maximum concentration value\
s issued 
by the European Technical Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum 
ConcentrationActual Concentration
Lead (Pb)0.1%< 0.1%
Mercury (Hg) 0.1%< 0.1%
Cadmium (Cd) 0.01%< 0.01%
Hexavalent Chromium (Cr
6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1%< 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III 
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. 0HUFXU\LQFROGFDWKRGHÀXRUHVFHQWODPSVDQGH[WHUQDOHOHFWURGH ÀXRUHVFHQW
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length ( Ù500 mm): maximum 3.5 mg per lamp.
(2) Medium length ( ×500 mm and Ù1,500 mm): maximum 5 mg per lamp.
(3) Long length ( ×1,500 mm): maximum 13 mg per lamp.
2.  Lead in glass of cathode ray tubes.
3.  /HDGLQJODVVRIÀXRUHVFHQWWXEHVQRWH[FHHGLQJE\ZHLJKW
4.  Lead as an alloying element in aluminium containing up to 0.4% lead by w\
eight.
5.  Copper alloy containing up to 4% lead by weight.
6.  Lead in high melting temperature type solders (i.e. lead-based alloys c\
ontaining  85% by weight or more lead).
7.  Electrical and electronic components containing lead in a glass or ceram\
ic other  than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or \
in a glass or 
ceramic matrix compound. 
						

							iv
Copyright Information
Copyright © ViewSonic®
 Corporation, 2016. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks 
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered 
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. 
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines 
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial erro\
rs 
or omissions contained herein; nor for incidental or consequential damag\
es resulting 
from furnishing this material, or the performance or use of this product\
.
In the interest of continuing product improvement, ViewSonic Corporation reserves 
WKHULJKWWRFKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFX -
ment may change without notice.
No part of this document may be copied, reproduced, or transmitted by an\
y means, 
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional prod\
uct information 
as it becomes available, please visit your region section on ViewSonic’\
s website to 
register your product online.
The ViewSonic CD also provides an opportunity for you to print the produ\
ct 
registration form. Upon completion, please mail or fax to a respective V\
iewSonic 
office. To find your registration form, use the directory “:\CD\Reg\
istration”. 
Registering your product will best prepare you for future customer servi\
ce needs.
Please print this user guide and fill the information in the “For You\
r Records” section. 
For additional information, please see the “Customer Support” sect\
ion in this guide.
For Your Records
Product Name: PJD6252L/PJD6551W/PJD7326/PJD7526W/PJD7720HD
ViewSonic DLP Projector
Model Number: VS16443/VS15913/VS16444/VS16445/VS16483
Document Number: PJD6252L/PJD6551W/PJD7326/PJD7526W/PJD7720HD_
UG_ENG Rev. 1B 05-04-16
Serial Number: ________________________________________
Purchase Date: ________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you \
and the 
environment. Please use care and dispose of in accordance with local, st\
ate or  
federal laws.
ViewSonic respects the environment and is committed to working and living\
 green. 
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic 
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx 
						

							1
Table of contents
Important safety 
instructions .......................2
Introduction .... ..................4
Projector features ................................. 4
Shipping contents ................................. 5
Projector exterior view ......................... 6
Controls and functions ......................... 7
Positioning your 
projector..........................12
Choosing a location............................ 12
Projection dimensions ........................ 13
Connection ...... ................16
Connecting a computer or monitor .... 17
Connecting Video source devices ...... 18
Playing sound through the projector .. 20
Using the cable management cover (for 
selected models) ................................. 21
Operation ........................22
Starting up the projector..................... 22
Using the menus................................. 23
Utilizing the password function ......... 24
Switching input signal........................ 26
Adjusting the projected image ........... 27
Magnifying and searching for details. 29
Selecting the aspect ratio ................... 30
Optimizing the image......................... 31
Setting the presentation timer ............ 35
Hiding the image ................................ 36
Locking control keys.......................... 36
Creating your own startup screen....... 36 Operating in a high altitude 
environment ....................................... 37
Using the CEC function..................... 37
Using the 3D functions ...................... 38
Controlling the projector through a LAN 
environment (for selected models) .... 39
Using the projector in standby mode . 46
Adjusting the sound ..
......................... 46
Shutting down the projector .............. 48
Menu operation .................................. 49
Maintenance ...................59
Care of the projector .......................... 59
Using the dust filter (optional accessory) ........................................................... 59
Lamp information .............................. 61
Troubleshooting .............64
Specifications ..................65
Projector specifications...................... 65
Dimensions ........................................ 67
Ceiling mount installation ................. 67
Tripod mount installation .................. 67
Timing chart ...................................... 68
Copyright information...72
Appendix .........................73
IR control table .................................. 73
RS232 command table ....................... 74 
						

							2
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information 
technology equipment. However, to ensure safe  use of this product, it is important that you 
follow the instructions mentioned in  this manual and marked on the product. 
Safety Instructions
1.Please read this manual before you operate your projector.  Save it for future 
reference.
2. Do not look straight at the projector lens during operation.  The intense light beam 
may damage your eyes.
3. Refer servicing to qualified service personnel. 
4. Always open the lens shutter or remove the lens cap when the projector lamp is 
on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate  safely within a mains voltage between 100 to 240 volts AC, but could fail if power 
cuts or surges of  ±10 volts occur.  In areas where the mains voltage may fluctuate 
or cut out, it is recommended that you connect your projector through a power 
stabilizer, surge protector or uninterruptible power supply (UPS). 
6. Do not block the projection lens with  any objects when the projector is under 
operation as this could cause the objects to become heated and deformed or even 
cause a fire. To temporarily turn off th e lamp, press BLANK on the projector or 
remote control.
7. The lamp becomes extremely hot during ope ration. Allow the projector to cool for 
approximately 45 minutes prior to rem oving the lamp assembly for replacement. 
8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps  beyond the rated life could cause them to break on rare occasions. 
9. Never replace the lamp assembly or any electronic components unless the projector is  unplugged. 
10. Do not place this product on an unstable cart, stand, or table. The product may fall,  sustaining serious damage. 
11. Do not attempt to disassemble this projector . There are dangerous high voltages inside 
which may cause death if you should come into  contact with live parts. The only user 
serviceable part is  the lamp which has its own removable cover.
Under no circumstances should you ever u ndo or remove any other covers. Refer 
servicing only to suitably qualifi ed professional service personnel.
12. Do not place this projector in any of the following environments. 
-  Space that is poorly ven tilated or confined. Allow at least 50 cm clearance from walls 
and free flow of air around the projector.
-  Locations where temperatures may become  excessively high, such as the inside of a 
car with all windows rolled up.
-  Locations where excessive humidity, dust,  or cigarette smoke may contaminate optical 
components, shortening th e projectors life span and darkening the picture.
-  Locations near fire alarms
-  Locations with an ambient  temperature above 40°C / 104°F
-  Locations where the altitudes are  higher than 3000 m (10000 feet). 
						

							3
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, 
overheating inside the projector may result in a fire.
-  Do not place this projector on a blan ket, bedding or any other soft surface. 
-  Do not cover this projector with a cloth or any other item. 
-  Do not place inflammables near the projector.   
14. Always place the projector on a leve l, horizontal surface during operation.
-  Do not use if tilted at an angle of more than 10 degrees left  to right, nor at angle of 
more than 15 degrees front to back. Using the projector when it is not fully horizontal 
may cause a malfunction of,  or damage to, the lamp.
15. Do not stand the projector on  end vertically. Doing so may cause the projector to fall 
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place  any objects upon it. Besides probable physical 
damage to the projector, doing so may re sult in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may  cause it to fail. If the projector does become wet, disconnect it from the power 
supplys wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation. 
Use only qualified ceiling mount kit for mounting the projector and ensure it is 
securely installed. 
19. When the projector is under operation, you  may sense some heated air and odor from 
its ventilation grill. It is a normal  phenomenon and not a product defect.
20. Do not use the Security bar for transporting  or installation. It should be used with a 
commercially available theft prevention cable. 
Safety instructions for  ceiling mounting of the 
projector
We want you to have a pleasant experience usi ng your projector, so we need to bring this 
safety matter to your attention to pr event damage to person and property.
If you intend to mount your projector on the  ceiling, we strongly recommend that you use a 
proper fitting projector ceiling mount kit and th at you ensure it is securely and safely 
installed.
If you use an inappropriate projector ceiling  mount kit, there is a safety risk that the 
projector may fall from the ceiling due to an  improper attachment through the use of the 
wrong gauge or length screws.
You can purchase a projector  ceiling mount kit from the place  you purchased your projector. 
We recommend that you also purchase a separate  security cable and attach it securely to 
both the anti-theft lock slot on the projector a nd the base of the ceiling mount bracket. This 
will perform the secondary role of restraining the projector  should its attachment to the 
mounting bracket become loose. 
						

							4
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly 
design to deliver high reliability and ease of use.
The projector offers th e following features.
• Dynamic mode adjusting the power consumption of the lamp according to the  brightness of the image being projected
• Power saving function decreas ing the power consumption of the lamp by up to 70% 
when no input signal can be det ected for a set period of time.
• Presentation timer for better co ntrol of time during presentations
•
LAN Settings allowing management of projector st atus from a remote computer (for selected 
models)
• Supports 3D display
•Color  Management allowing color adjustments to your liking
• Less than 0.5W power consumption wh en power saving mode is turned on
• Screen Color correction allowing projection  on surfaces of several predefined colors
• Quick auto search speeding  up the signal detecting process
• Color modes providing choices for different projection purposes
• Selectable quick power off function
• One-key auto-adjustment to display the best picture quality
• Digital keystone correction and 4 corner ad justment (for selected models) to correct 
distorted images
• Adjustable color management control for data/video display
• Ability to display 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic mode s to reduce the power consumption
• Component HDTV compatibility (YP
bPr)
• HDMI CEC (Consumer Electronics Control)  function allows synchronized power ON/
OFF operation between the projector and a CEC-compatible DVD player device 
connected to the HDMI input of the projector
The apparent brightness of the projected image will vary depending on the ambient lighting 
conditions, selected input signal contrast/brigh tness settings, and is directly proportional to 
projection distance.
The lamp brightness will decline over time and may vary within the lamp manufacturers 
specifications. This is normal and expected behavior. 
						

							5
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these 
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those 
illustrated.
Optional accessories
1. Replacement lamp (RLC-092 for PJD6252L. RLC-093 for PJD6551W. RLC-104 for 
PJD7326. RLC-105 for PJD7526W . RLC-100 for PJD7720HD.)
2. Soft carry case
3. VGA-Component adapter
4. Dust filter Projector Power Cord
VGA Cable (for selected models) Multi-language User 
Manual CD Quick Start Guide
Remote Control & Batteries Cable management 
cover (for selected  models)