ViewSonic Projector PJD6211 User Manual

							 EN-18
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings. 
						

							EN-19
 
*1 Adjustable range and default setting vary depending on signal type.
*2 This function is only available when the projector is installed an optional filter cover. 
						

							 EN-20
How to operate
1. Press the MENU button to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3.After selecting the desired main menu item, press X to enter sub-menu for
feature setting.
4. Use S / T to select the desired item and adjust the settings with W / X.
5. Press the MENU button, the screen will return to the main menu.
6. To exit OSD, Press the MENU button again. The OSD menu will close and the
projector will automatically save the new settings.
Picture (Computer / Video Mode)
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range and saturation according to your
preference.
Keystone
Manually correct distorted images resulting from an angled projection.
Aspect Ratio
Select how the picture fits on the screen:
„4:3 : The input source will be scaled to fit the projection screen.
„16:9 : The input source will be scaled to fit the width of the screen.
Image
There are many factory presets optimized for various types of images.
„PC : For computer or notebook.
„Movie : For home theater.„sRGB : For PC standard color.
„User : Memorize user’s settings.
„White Board : For white projection screen type.„Black Board : For black projection screen type.
„Green Board: For green projection screen type. 
„Daylight Mode: For a daylight environment.
White Intensity
Increase the brightness of white areas. 
						

							EN-21
GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
3D Sync
„On: 120Hz detection 
„Off: Disable 120Hz
3D Sync Invert
„On: Invert left and right frame contents.
„Off: Default frame contents.
Computer Image (Computer Mode)
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Video Image (Video Mode)
Saturation
Adjust a video image from black and white to fully saturated color.
Sharpness
Sharpen or soften the image.
Tint
Shift colors toward red or green.
Sound (Computer / Video Mode)
Vo l u m e
Adjust the volume level.
Mute
Cut off the sound temporarily.
Setting (Computer / Video Mode)
Menu Position
Choose the menu location on the display screen.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Signal Type 
						

							 EN-22
Specify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to
project.
„Auto : Automatically detect the input signal type from COMPUTER IN 1 and 
COMPUTER IN 2 terminals.
„RGB : For VGA signal
„YCbCr/YPbPr:For component signal
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Lamp Hours Reset
Reset the lamp Hour to 0 hours.
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter
cover.
Filter Hours
Display the filter’s elapsed operating time (in hours).
„When Filter Mode is turned on, the Filter Hours also turns on automatically.
Filter Hours Reset
Reset the filter Hour to 0 hours.
Power Saving
If no operation is performed for a specific period of time, projector will automatically
turn off.
Auto Source
Automatically scan through all the input source.
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life.
„This function will be unavailable when the DCR function is on.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
OSD Timeout
Duration of OSD menu display countly starts (at idle state by second).
Option (Computer / Video Mode)
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Password 
						

							EN-23
Set or change the password. When the password function is added, image projection
will require to input the preset password when turning on the projector.
Screen Capture
Capture the current projection screen as a start-up screen.
Start-up Screen
Select start-up screen when the projector is powered on or when no signal is input.
User is the screen that you captured.
Digital Zoom
Zoom in and out the images.
DCR (Dynamic Contrast Ratio)
Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable
DCR will resume to normal contrast performance. DCR will impact lamp life and
system noise performance.
Closed Caption
Enable or Disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2, T3, T4 or OFF.
Brilliant Color             
Produce an expanded on-screen color spectrum that delivers enhanced color
saturation for bright, true-to-life images. Suggesting to turn Off for most video sources
and On for most computer sources. 
Green Mode
Enable this function when power consumption is under 1W.
Language (Computer / Video Mode)Select the language used by the on-screen menu.
Factory Default (Computer / Video Mode)Restore settings to factory default .
System Info (Computer / Video Mode)
Source
Display the input source.
Resolution
Display the resolution.
H. Frequency
Display H. Frequency.
V. Frequency
Display V. Frequency. 
						

							
 EN-24
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.Warning
Never open any of the covers on the projector. Dangerous electrical voltages
inside the projector can cause severe injury. Do not attempt to service this
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
„Turn off the projector and remove the AC power cord from the power outlet 
before beginning maintenance work.
„Make sure the lens is cool before cleaning.„Do not use detergents or chemicals other than those noted above. Do not use 
benzene or thinners.
„Do not use chemical sprays.„Use a soft cloth or lens paper only. 
						

							EN-25
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp is extremely hot right after turning off the projector. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait for at least 
45 minutes for the lamp to cool down.
„Do not touch the lamp glass at any time. The lamp may explode due to 
improper handling, including the touching of the lamp glass.
„Lamp lifetime may differ from lamp to lamp and according to the environment 
of use. There is no guarantee of the same lifetime for each lamp. Some lamps 
may fail or terminate their lifetime in a shorter period of time than other similar 
lamps.
„A lamp may explode as a result of vibration, shock or degradation as a result of 
hours of use as its lifetime draws to an end. Risk of explosion may differ 
according to the environment or conditions in which the projector and lamp are 
being used.
„Wear protective gloves and eyeglasses when fixing or detaching the lamp.„Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least 
for 5 minutes to turn off the projector after powering on.
„Do not operate the lamp in proximity to paper, cloth, or other combustible 
material nor cover it with such materials.
„Do not operate the lamp in an atmosphere containing an inflammable 
substance, such as thinner.
„Thoroughly ventilate the area or the room when operating the lamp in an 
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, 
nausea, dizziness, and other symptoms.
„The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury 
inside the lamp will be exposed. Leave the area immediately if the lamp 
shatters while being operated and ventilate the area for at least 30 minutes in 
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to 
user’s health. 
						

							 EN-26
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try  reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Setting” menu.
„Dispose the used lamp according to local regulations.„Ensure that screws are tightened properly. Screws not tightened fully may 
result in injury or accidents.
„Since the lamp is made of glass, do not drop the unit and do not scratch the 
glass.
„Do not reuse the old lamp. This could cause the lamp to explode.„Be sure to turn off the projector and unplug the AC power cord before 
replacing the lamp.
„Do not use the projector with the lamp cover removed. 
						

							EN-27
Specifications
Display system   Single  1.397cm /  0.55  DLP  p a nel
Resolution XGA (1024 × 768)
Zoom   1.2 X
F/No. 2.51 - 2.69
Focal length 21.95 - 24.18
Scre en size   76.2cm ~ 762cm /  30” – 300”
Lamp 180W
Input terminal D-Sub 15-pin x 2, S-VIDEO x 1, VIDEO x 1, Audio signal input  (3.5 mm stereo mini jack) x 1
Output terminal D-Sub 15 pin x 1,  Audio si gnal output (3.5 mm stereo mini jack) x 
1, 12-Vdc trigger output x 1
Control terminal RS-232 x 1, USB x 1
Speaker 2 watt x 1
Video compatibility NTSC, NTSC 4.43 PAL, PAL-N, PAL M
SECAM, HDTV (480p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency 31 - 80 KHz
50 - 120 Hz
Environment Operating: Temperature: 0°C to 40°C
Humidity: 30%-85%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power requirement AC 100-240 V, 50 - 60 Hz, 2.3A
Power consumption 240 W
Dimensi on  (W  x D  x  H)  279.5 mm  x 2 18 mm  x 105 mm  / 11.0 x 8.6 x 4.1
Weight 2.7 kg (6lb)
Note: Design and Specifications are subject to change without prior notice.