ViewSonic Projector PJ658D User Manual
Have a look at the manual ViewSonic Projector PJ658D User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 617 ViewSonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
26ViewSonic PJ658D Language (Computer / Video Mode) Choose the mult l ngual OSD menu. Use the / buttons to select your preferred language. Press button to finalize the selection. Factor y Reset (Computer / Video Mode) Choose “Yes” and press MENU button to return the d splay parameters on all menus to the factory default sett ngs.
ViewSonic PJ658D27 Maintenance The projector needs proper ma ntenance. You should keep the lens clean as dust, d rt or spots w ll project on the screen and d m n sh mage qual ty. If any other parts need replacing, contact your dealer or qualified service personnel. When cleaning any part of the projector, always switch off and unplug the projector first. Warning: Never open any of the covers on the projector. Dangerous electr cal voltages ns de the projector can cause severe njury. Do not attempt to serv ce th s product yourself. Refer all servicing to qualified service personnel. Cleaning the Lens Gently w pe the lens w th lens clean ng paper. Do not touch the lens w th your hands. Cleaning the Projector Housing Gently w pe w th a soft cloth. If d rt and sta ns are not eas ly removed, use a soft cloth damped w th water, or water and neutral detergent, and w pe dry w th a soft, dry cloth. Turn off the projector and remove the AC power cord from the power outlet before beginning maintenance work. Make sure the lens is cool before cleaning. Do not use detergents or chemicals other than those noted above. Do not use benzene or thinners. Do not use chemical sprays. Use a soft cloth or lens paper only.
28ViewSonic PJ658D Replacing the Lamp Projector lamps have a finite life. Replace the lamp when: A warn ng message “Lamp s approach ng the end of ts useful l fe n full power operat on. Replacement suggested!” appears on the screen. The mage becomes darker and hues become weaker after a lamp has been for a long per od of t me. The projector lamp LED nd cator turns nto amber. Refer to sect on t tled “Indicator Messages” for further deta ls. The lamp becomes high temperature after turning off the projector with the power button. If you touch the lamp, you may scald your finger. When you replace the lamp, wait for at least 45 minutes for the lamp to cool down. Do not touch the lamp glass at any time. The lamp may explode due to improper handling, including the touching of the lamp glass. Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps. A lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used. Wear protective gloves and eyeglasses when fixing or detaching the lamp. Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5 minutes to turn off the projector after powering on. Do not operate the lamp in proximity to paper, cloth, or other combustible material nor cover it with such materials. Otherwise it could cause a fire. Do not operate the lamp in an atmosphere containing an inflammable substance, such as thinner. Otherwise it could cause a fire or explosion. Thoroughly ventilate the area or the room when operating the lamp in an oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness, etc. The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the lamp will go out of the projector. Leave the area immediately if the lamp shatters while being operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to user’s health.
ViewSonic PJ658D29 1. Turn off the projector and unplug the AC power cord. 2. Place a protect ve sheet (cloth) beneath the projector. Turn the projector over so you can access the lamp cover. 3. Remove the access panel screws and open the panel. 4. Remove the screws on the bottom of the lamp assembly. 5. Grasp the lamp handle and pull the lamp assembly d rectly out of the projector. 6. Replace w th the new lamp. 7. Place back the screws on the bottom of lamp assembly. 8. Place the panel and screw back the screws on the lamp cover. 9. Reset the lamp hour. Refer to the “Management (Computer/V deo Mode)” menu. Dispose of the used lamp according to local regulations. Ensure that screws are tightened properly. Screws not tightened fully may result in injury or accidents. Since the lamp is made of glass, do not drop the unit and do not scratch the glass. Do not reuse the old lamp. This could cause the lamp to explode. Be sure to turn off the projector and unplug the AC power cord before replacing the lamp. Do not use the projector with the lamp cover removed.
30ViewSonic PJ658D Technical Specifications D splay Type 0.7” DMD/ 12°/ DDR Nat ve resolut on 786,432 dot x1 (1024 x 768 x1) Lens Manual Zoom (1.2X) Focal Length 23.6 - 28.25 mm Aspect Rat o Auto, 4:3, 16:9 Screen S ze 30 - 300 nches Lamp 250W Project on Type Front, Rear, Ce l ng V deo Input NTSC, NTSC4.43 PAL-60, M, N, B, D, G, H, I SECAM Input Source Computer, HDTV, S-V deo, V deo Scann ng Frequency Hor zontal Freq. 15 - 80 KHz Vert cal Freq. 50 - 85 Hz P xel Rate 25 - 135 MHz D g tal Keystone Correct on Vert cal: +/- 16 degrees Analog RGB ( nput s gnal) D-Sub 15-p n connector HDTV D splay 480 , 480p, 576 , 576p, 720p, 1080 Integrated Speaker 2W x 1 Remote Control Mult funct onal OSD Language Mult language Storage Temperature -20 - + 60°C Operat on Temperature +0 - +40°C Operat on Hum d ty 5 - 90% (Non-Condens ng) Power Requ rement AC 100 – 240V, 50 / 60 Hz Power Consumpt on 300W (Typ cal) D mens on (W x D x H) 290 x 220 x 95 mm We ght 3.0kgs (6.6lbs) Note: Design and Specifications are subject to change without prior notice.
ViewSonic PJ658D31 Appendix LED Indicator Messages LED TypeColorStatusMeaning Power LED Green Flash ngThe projector s powered and ready. Power LED Amber Flash ngThe projector system has some problems w th ts fan, so the projector cannot start up. Lamp LED Green Sol dThe lamp s n good cond t on and s project ng at max mum br ghtness. Lamp LED Amber Sol dThe lamp has reached ts end of l fe and must be changed soon. The lamp w ll cont nue to operate unt l t fa ls. Change the lamp. If the lamp s off, then the ballast w ll become malfunct on Lamp LED Off- The projector s shutt ng The fan motor s cool ng the lamp for shutdown. Do not unplug the power cable or turn the power sw tch off before the Power LED change to Flash ng. The fan motor w ll turn off when the lamp has cooled. Power LED Amber Sol dTemperature s too h gh. The lamp w ll turn off. The fan motor s cool ng the lamp. Lamp LED Red Flash ngThe lamp gn t on fa l. If temperature s too h gh, the fans w ll be cool ng the lamp.
32ViewSonic PJ658D Compatibility Modes Computer: Mode Resolution Horizontal Frequency Vertical Frequency Factory Preset Mode: (Analog=26) PC: Full scan *Pr mary Preset Mode Signal Resolution Horizontal Frequency Vertical Frequency 1080i 19201x080 60 Hz 33.75 1080i 1920x1080 50 Hz 28.13 720p 1280x720 60 Hz 45.0 720p 1280x720 50 Hz 37.5 576i 720x576 50 Hz 15.75 576p 720x576 50 Hz 31.25 480p 640x480 60 Hz 31.5 480i 640x480 60 Hz 15.75 Mode VGA (Expanded) DOS/Text mode v s ble SVGA (Expanded) XGA (Nat ve) SXGA (Compressed) Mac II 13” Mac 16” Mac 16” Mac 19” Other (Compressed)640x480640x480640x480640x480720x400720x400800x600800x600800x600800x600800x600*1024x7681024x7681024x7681024x7681280x10241280x1024640x480832x6241152x8701024x7681152x8641152x8641152x8641280x9601280x960 59.9572.8175.0085.0070.0085.00566072758560707585607566.774.575757075856075 31.4737.8637.5043.2731.537.935.237.9 48.146.953.748.456.560.068.764.080.035.049.768.660.264.067.577.560.075.0
ViewSonic PJ658D33 Troubleshooting Refer to the symptoms and measures l sted below before send ng the projector for repa rs. If the problem pers sts, contact your local reseller or serv ce center. Please refer to “Ind cator Messages” as well. SymptomCauseMeasure No power.The AC power cord s not plugged n. Plug n the AC power cord. The AC power cord s not connected to the projector.Connect the AC power cord to the projector correctly and turn on the ma n power sw tch. The ma n power sw tch s not turned on.Turn on the ma n power sw tch. The lamp cover loose.T ghten the screws on the lamp cover. Power goes out during use.The temperature s too h gh. Unplug the AC power cord and wa t for a short wh le, then turn the power back on. The vent lat on holes are blocked.Place the projector so that the vent lat on holes are not blocked. No image appears on screen.The projector s not turned on. Turn the projector on. The connect ons set up are not correctly. Check that all connect ons are setup correctly. The connected dev ces are not funct on ng properly. Check that all connected dev ces are funct on ng properly. Lens cap s not removed. Remove the lens cap and turn the projector on. “H de” funct on s act vated. Cancel “H de” funct on. Partial, scrolling or incorrectly displayed image. The nput s gnal s not supported by the projector. Press “Resync” button. Image is unstable or flickering.The s gnal t m ng of the d splay does not synchron ze w th the graph c card.Use “Track ng” to correct t. Refer to Computer Image sect on. Change the mon tor color sett ng from your computer. Image has vertical flickering bar.The d splay data frequency does not match the frequency of your computer’s graph c card.Use “Frequency” to make an adjustment. Refer to Computer Image sect on.Check and reconfigure the display mode of your graph c card to make t compat ble w th the product.
34ViewSonic PJ658D SymptomCauseMeasure Image is out of focus.The lens focus s not adjusted opt mally. Adjust the focus w th the focus r ng. The project on d stance s not w th n the projector’s supported range.Place the projector w th n the supported range. Remote control doesn’t work.The batter es could be weak. Replace w th a new set of batter es. The polar ty s not correct. Install the batter es w th correct polar t es. The remote control s not be ng used w th n the effect ve range. Use the remote control w th n the effect ve range. There are some obstruct ons between the remote control and projector. Check that there are not obstruct ons between the remote control and projector. There are some fluorescent or other br ght l ghts sh n ng at the projector’s nfrared remote Check that there are not any fluorescent or other br ght l ghts sh n ng at the projector’s nfrared remote sensor.
ViewSonic PJ658D35 Customer Support For techn cal support or product serv ce, see the table below or contact your reseller. Note : You w ll need the product ser al number. Country/RegionWeb SiteT=Telephone F=FaxE-mail Un ted States www.v ewson c.com/support/ T= 800 688 6688 F= 909 468 1202 serv ce.us@v ewson c.com Canadawww.v ewson c.com/supportT= 866 463 4775serv ce.ca@v ewson c.com Un ted K ngdom www.v ewson ceurope.com/ukT= 0207 949 0307serv ce.eu@v ewson ceurope.com Europe, M ddle East, Balt c countr es, and North Afr ca www.v ewson ceurope.comContact your resellerserv ce.eu@v ewson ceurope.com Austral a and New Zealand www.v ewson c.com.au/ support/ AUS= 1800 880 818 NZ= 0800 008 822serv [email protected] ewson c.com S ngapore/ Malays a/ Tha land www.v ewson c.com.sg/ support/ T= 65 64616044 serv [email protected] ewson c.com South Afr ca/Other countr es www.v ewson c.com T= 886 2 2246-3456 F= 886 2 2249-1751serv [email protected] ewson c.com Hong Kong www.hk.v ewson c.com/ support/ T= 852 3102 2900 serv [email protected] ewson c.com Macauwww.hk.v ewson c.com/support/T= 853 700 303 serv [email protected] ewson c.com Korea www.v ewson c.comT= 080 265 9080serv [email protected] ewson c.com