ViewSonic Pro10100 Projector User Manual

							40
SCREEN | PIP / POP
Screen
 
` Single Screen: Projection single window.
 
`
 PIP Screen: Main source is at large window; PIP source is at small 
window and displays in the corner of the main window.
 
`
 POP Screen: Main source is at the left window and POP source is at the \
right widow, they are equal sizes and side by side.
PIP Location
Choose the PIP screen position on the display screen.
PIP Size
Choose the PIP size from 1/16, 1/25 or 1/36 on the display screen.
PIP / POP Source
Choose the source to switch PIP/POP window source.
Swap
Press to swap the sources of main window and PIP/POP window.
Some source/signal combinations may not be compatible with PIP/POP funct\
ion. 
Please refer to the table below:
PIP/POP  source Main Source
HDMI VGADVI-D BNCS-video Video
HDMI VVVV
VGA VVVV
DVI-D VV
BNC VV
S-video VV
Video VV
NOTE: VGA and BNC can support Component.  
						

							41
SETTING
Language
Choose the multilingual OSD menu. Press ◄ or ► into the sub menu and then use 
the ▲ or ▼ to select your preferred language. Press “Enter” to finalize the selection.
Projection
 
` Front-Desktop
     This is the default selection. The image is projected straight on t\
he screen.  
`
 Rear-Desktop
     When selected, the image will appear reversed.  
`
 Front-Ceiling
     When selected, the image will turn upside down.  
`
 Rear-Ceiling
     When selected, the image will appear reversed in upside down positi\
on.  
						

							42
 
  Rear-Desktop and Rear-Ceiling are to be used with a translucent screen.
Menu Location
Choose the menu location on the display screen.
SETTING | Lens Function
Focus
Adjust focus function on the projected image.
Zoom
Adjust zoom function on the projected image.
Lens Shift
Shift the projected image.
 
` Lock: This function can not be used by user.
 
` Unlock: This function can be used by user.
Lens Calibration
Perform calibration and return lens to the center position.  
						

							43
SETTING | Security
Security Timer
Use this function to set the how long (Month/Day/Hour) the projector c\
an be used. 
Once this time has elapsed you will be requested to enter your password \
again.
Change Password
 
` First time:
1. Press “
” to set the password.
2.  The password has to be 4 digits.
3.  Use number button on the remote to enter your new password and then 
press “
” key to confirm your password.
 
` Change Password:
1. Press “
” to input old password.
2.  Use number button to enter current password and then press “
” to 
confirm.
3.  Enter new password (4 digits in length) using the number buttons on th\
e 
remote, then press “
” to confirm.
4.  Enter new password again and press “
” to confirm.
 
` If the incorrect password is entered 3 times, the projector will automat\
ically shut 
down.
 
` If you have forgotten your password, please contact your local office for support.
 
  Password default value is “1234” (first time).
 
  Always keep the password in your files. If the password is forgotten or lost,   
please contact your local authorized service center.
   
						

							44
Security
 
` On: Choose “On” to use security verification when turning on projector.
 
` Off: Choose “Off” to be able to switch on the projector without pa\
ssword 
verification.
SETTING | Signal (RGB)
 
  Signal is supported except Video and S-Video.
Frequency
Change the display data frequency to match the frequency of your compute\
r’s 
graphic card. Use this function only if the image appears to flicker vertically.
Phase
Synchronize the signal timing of the display with the graphic card. If t\
he image 
appears to be unstable or flickers, use this function to correct it.
H. Position
 
` Press the ◄ to move the image left.
 
` Press the ► to move the image right.
V. Position
 
` Press the ◄ to move the image down.
 
` Press the ► to move the image up.
Automatic
Automatically detects the signal. If you use this function, the phase, f\
requency items 
are grayed out, and if signal is not automatic, the phase, frequency ite\
ms will appear 
for user to manually tune and saved in settings after that for next time\
 projector 
turns off and on again.  
						

							45
SETTING | Signal (Video)
 
  “Signal” is only supported when the source is Video or S-video.
White Level
Allow user adjust White Level when inputting S-Video or Video signals.
Black Level
Allow user adjust Black Level when inputting S-Video or Video signals.
Saturation
Adjust a video image from black and white to fully saturated color.
 
` Press the ◄ to decrease the amount of saturation in the image.
 
` Press the ► to increase the amount of saturation in the image.
IRE
Adjust measurement of composite video signals.
 
  “IRE” is only supported on NTSC signal.
Projector ID
ID definition can be set up by menu (range 0-99) to indicate an individual projector.  
						

							46
SETTING | Audio Settings
Internal Speaker
Choose the “On” or “Off” to turn on or off the internal spea\
ker.
Mute
 
` Choose the “On” to turn mute on.
 
` Choo
se the “Off” to turn mute off.
Volume
 
` Press the ◄ to decrease the volume.
 
` Press the ► to increase the volume.  
						

							47
SETTING | Advanced
Logo
Use this function to set the desired startup screen. If changes are made\
 they will 
take effect the next time the projector is powered on. 
` Viewsonic: The default startup screen.
 
` Neutral: Logo is not displayed on startup screen.
 
` User: Use stored picture from “Logo Capture” function.
Logo Capture
Press  to capture an image of the picture currently displayed on screen.
Closed Captioning
If changes are made they will take effect the next time the projector is\
 powered on.
 
` Off: select “off” to turn off the closed captioning feature.
 
` CC1: CC1 language: American English.
 
` CC2/CC3/CC4: CC2/CC3/CC4 language (depending on the TV channel of the 
user): Spanish, French, Portuguese, German, Danish.  
						

							48
SETTING | Network
Network State
Display the network connection status.
DHCP
Use this function to select your desired startup screen. If you change t\
he setting 
from one to another, when you exit the OSD menu, the new setting will ta\
ke effect 
on next open. 
` On: Assign an IP address to the projector from an external DHCP server 
automatically.
When making a connection in the local area network.
1. Connect the computer and the projector to your network.
2. Press the ‘menu’ key in the remote controller.
3. Select Setting -> Network -> DHCP (as following).
4. DHCP mode selects ‘On.’ If IP Address is 0.0.0.0, please check the connection and try again.
If still can not get the IP Address, please contact your network adminis\
trator.
 
` Off: 
Assign an IP address manually.
IP Address
Select an IP address.
Subnet Mask
Select subnet mask number.  
						

							49
Gateway
Select the default gateway of the network connected to the projector.
DNS
Select DNS number.
Apply
Press “” and then choose “Yes” to apply the selection.
 
  All of the new settings of the non-DHCP mode shall be triggered by “Yes”.
Control System IP Address
Select an IP address for Crestron Control System.
Control System IP ID
Select an IP ID for Crestron Control System.
Control System Port 
Select a connection port for Crestron Control System.