ViewSonic Pjd7583wi Projector User Manual

							
Operation 27
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These 
adjusters change the image height and pr ojection angle. To adjust the projector:
1. Press the quick-release button and lift the  front of the projector. Once the image is 
positioned where you want it, release the 
quick-release button to lock the foot in 
position.
2. Screw the rear adjuster feet to fine tune the  horizontal angle.
To retract the foot, hold up the projector while 
pressing the quick-release button, then slowly 
lower the projector. Screw  the rear adjuster feet 
in a reverse direction.
If the projector is not pl aced on a flat surface or 
the screen and the projector are not 
perpendicular to each other, the projected image 
becomes trapezoidal. To correct this situation, 
see  Correcting keystone on page 28  for details.
• Do not look into the lens while the lamp is on. 
The strong light from the lamp may cause 
damage to your eyes.
• Be careful when you press the adjuster button  as it is close to the exhaust vent where hot air 
comes from.
Auto-adjusting the image
In some cases, you may need to optimize the 
picture quality. To do this, press  AUTO on the 
projector or remote control. Within 3 seconds, 
the built-in Intelligent Auto Adjustment 
function will re-adjust the values of Frequency 
and Clock to provide the best picture quality.
The current source information will be 
displayed in the upper left corner of the screen 
for 3 seconds.
• The screen will be blank while AUTO is 
functioning.
• This function is only available when PC  signal (analog RGB) is selected.
122 
						

							
Operation
28
Fine-tuning the image clarity
Sharpen the image by rotating the focus ring.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably  wider at either the 
top or bottom. It occurs wh en the projector is not perpendicular to the screen.
To correct this, besides adjust ing the height of the projector, you will need to manually 
correct it following one of these steps.
• Using the remote control
Press  /  on the projector or remote control to 
display the Keystone correction page. Press   to 
correct keystoning at the t op of the image. Press   
to correct keystoning at the bottom of the image.
• Using the OSD menu
1. Press  MENU/EXIT  on the projector or 
Menu  on the remote control and then press 
/  until the 
DISPLAY menu is 
highlighted.
2. Press  to highlight  Keystone and press 
MODE/ENTER  on the projector or  ENTER 
on the remote control. The  Keystone 
correction page is displayed.
3. Press   to correct keystoning at the top of  the image or press   to correct keystoning at 
the bottom of the image.
Press/.Press /. 
						

							
Operation 29
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the 
direction arrow keys fo r navigating the picture.
• Using the remote control
1. Press  Magnify +/-  to display the Zoom bar.
2. Press  Magnify + to magnify the center of the 
picture. Press the key repeatedly until the 
picture size is suit able for your need.
3. Use the directional arrows ( ,  ,  ,  ) on  the projector or remote control to navigate the 
picture.
4. To restore the picture to its original size, press  AUTO . You can also press  Magnify -. When 
the key is pressed again, the picture is further 
reduced until it is restor ed to the original size.
• Using the OSD menu
1. Press  MENU/EXIT  on the projector or  Menu on the remote control and then press 
/  until the  DISPLAY menu is highlighted.
2. Press
  to highlight  Zoom and press  MODE/ENTER  on the projector or  ENTER 
on the remote control. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of Using th e remote control above. Or if you are using 
the projector control panel, co ntinue to the following steps.
4. Press   on the projector repeatedly to  magnify the picture to a desired size.
5. To navigate the picture, press  MODE/ENTER on the projector or  ENTER on the 
remote control to switch to the paning m ode and press the directional arrows ( ,  , 
,  ) to navigate the picture.
6. Use the directional arrows ( ,  ,  ,  )  on the projector or remote control to 
navigate the picture.
7. To reduce size of the picture, press  MODE/ENTER on the projector or  ENTER on 
the remote control to switch back to  the zoom in/out functionality, and press AUTO to 
restore the picture to its original size. Y ou can also press   repeatedly until it is 
restored to the original size.
The picture can only be navigated after the picture is magnified. You can further magnify the 
picture while searching for details.
Selecting the aspect ratio
The aspect ratio is the ratio of the image  width to the image height. Most analog TV and 
computers are in 4:3 ratio,  and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing,  digital display devices like this projector can 
dynamically stretch and scale the image output to  a different aspect than that of the image 
input signal. 
To change the projected image ratio (n o matter what aspect the source is):
1. Press  MENU/EXIT  on the projector or  Menu on the remote control and then press 
/  until the  DISPLAY menu is highlighted.
2. Press
  to highlight  Aspect Ratio . 
						

							
Operation
30 3. Press  /  to select an aspect ratio to 
suit the format of the video signal and your 
display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active 
areas. OSD menus can be displayed on those unused black areas.
1. Auto: Scales an image proportionally to fit the 
projectors native reso lution in its horizontal 
width. This is suitable for the incoming image 
which is neither in 4:3 nor 16:9 and you want to 
make most use of the screen without altering the 
images aspect ratio.
2. 4:3: Scales an image so that it is displayed in the 
center of the screen with a 4:3 aspect ratio. This 
is most suitable for 4:3 images like computer 
monitors, standard definition TV and 4:3 aspect 
DVD movies, as it displays  them without aspect 
alteration.
3. 16:9: Scales an image so that it is displayed in 
the center of the screen with a 16:9 aspect ratio. 
This is most suitable for images which are 
already in a 16:9 aspect, like high definition TV, 
as it displays them wi thout aspect alteration.
4. 16:10 (PJD7583w/PJD7583wi only) : Scales an 
image so that it is disp layed in the center of the 
screen with a 16:10 aspect  ratio. This is most 
suitable for images which are already in a 16:10 
aspect as it displays them without aspect 
alteration.
15:9 picture
4:3 picture
16:9 picture
16:10 picture 
						

							
Operation 31
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined 
picture modes so that you can choose one to suit 
your operating environment and input signal 
picture type.
To select an operation mode that suits your need, 
you can follow one of the following steps.
• Press  MODE/ENTER  on the projector or 
Color Mode  on the remote control repeatedly 
until your desired mode is selected.
•Go to the  PICTURE > Color Mode  menu and press  /  to select a desired mode.
Picture modes for different types of signals
The picture modes available for differen t types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1. Brightest mode : Maximizes the brightness of the projected image. This mode is 
suitable for environments where extra-high  brightness is required, such as using the 
projector in well lit rooms.
2. PC mode : Is designed for presentations under da ylight environment to match PC and 
notebook coloring.
3. ViewMatch mode : Switches between high brightness performance and accurate color 
performance.
4. Cinema mode :  Is appropriate for playing colorful  movies, video clips from digital 
cameras or DVs through the PC input for best  viewing in a blackened (little light) 
environment.
5. User 1/User 2 mode : Recalls the settings customized  based on the current available 
picture modes. See  Setting the User 1/User 2 mode on page 32  for details.
Video input signals: S-Video, Vi deo, D-Sub / Comp. 1/2 (YPbPr)
1. Brightest mode : Optimized for daylight viewing,  with living room level ambient 
brightness.
2. Gaming mode : Suitable for all types of entert ainment media, including gaming and 
movies.
3. ViewMatch mode : Switches between high brightness performance and accurate color 
performance.
4. Cinema mode : Is suitable for enjoying dark movies or DVD movies best viewed in a 
blackened (little light) home cine ma or lounge room environment.
5. User 1/User 2 mode : Recalls the settings customized  based on the current available 
picture modes. See  Setting the User 1/User 2 mode on page 32  for details. 
						

							
Operation
32
Setting the User 1/User 2 mode
There are two user-definable modes if the curre nt available picture modes are not suitable 
for your need. You can use one of the picture modes (except the  User 1/User 2 ) as a starting 
point and customize the settings.
1. Press  MENU/EXIT  on the projector or  Menu on the remote control to open the On-
Screen Display (OSD) menu.
2. Go to the  PICTURE > Color Mode  menu.
3. Press /  to select  User 1 or User 2 .
4. Press   to highlight  Reference Mode .
This function is only available when User 1 or User 2 mode is selected up in the Color Mode 
sub-menu item.
5. Press  /  to select a picture mode  that is closest to your need.
6. Press   to select a sub-menu item to be changed and adjust the value with  / . 
See  Fine-tuning the image quality in user modes  below for details.
7. When all settings have been done, highlight  Save Settings and press MODE/ENTER  
on the projector or  ENTER on the remote control to store the settings.
8. The confirmation message  Setting Saved is displayed.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which 
may not be white, the  Screen Color feature can help correct the  projected picture’s colors to 
prevent possible color difference between  the source and projected pictures.
To use this function, go to the DISPLAY  > Screen Color menu and press  /  to select a 
color which is closest to the color of the pr ojection surface. There are several precalibrated 
colors to choose from:  Whiteboard, Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image qu ality in user modes
According to the detected signal type, there  are some user-definable functions available 
when  User 1  or User 2  mode is selected. You can make adjustments to these functions 
based on your needs.
Adjusting Brightness
Highlight the  PICTURE > Brightness  menu and press  / .
The higher the value, the br ighter the image. And the 
lower the setting, the darker the image. Adjust this 
control so the black areas of the image appear just as 
black and that detail in  the dark areas is visible.
Adjusting Contrast
Highlight the  PICTURE > Contrast  menu and press  / .
The higher the value, the great er the contrast. Use this 
to set the peak white level after you have previously 
adjusted the  Brightness setting to suit your selected 
input and viewing environment.
+50+30 +70
0-30+30 
						

							
Operation 33
Adjusting Color
Highlight the PICTURE > Color  menu and press  / .
Lower setting produces less saturated colors. If  the setting is too high, colors on the image 
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the  PICTURE > Tint  menu and press  / .
The higher the value, the more reddish the pict ure becomes. The lower the value, the more 
greenish the picture becomes.
Adjusting Sharpness
Highlight the  PICTURE > Sharpness  menu and press  / .
The higher the value, the sharper the picture b ecomes. The lower the value, the softer the 
picture becomes.
Adjusting Brilliant Color
Highlight the  PICTURE > Brilliant Color  menu and press  / .
This feature utilizes a new color-processing algorithm and system level enhancements to 
enable higher brightness while providing truer,  more vibrant colors in the projected picture. 
It enables a greater than 50% brightness incr ease in mid-tone images, which are common in 
video and natural scenes, so the projector reprodu ces images in realistic and true colors. If 
you prefer images with that quality, select  On. If you don’t need it, select  Off.
When  Off is selected, the  Color Temperature  function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature  menu and press  / .
The options available for color temperature*  settings vary according to the signal type 
selected.
1. T1: With the highest color temperature, T1  makes the image appear the most bluish 
white than other settings.
2. T2: Makes images appear bluish white.
3. T3: Maintains normal colorings for white.
4. T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be white for various purposes. One 
of the common methods of representing white co lor is known as the “color temperature”. A 
white color with a low color temperature appear s to be reddish white. A white color with a 
high color temperature appears to have more blue in it. 
						

							
Operation
34
Color Management
Only in permanent installations with controlled  lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allo w for more accurate color reproduction, should 
you require it.
If you have purchased a test disc which contains  various color test patterns and can be used 
to test the color presentation on monitors, TV s, projectors, etc., you can project any image 
from the disc on the screen and enter the  Color Management menu to make adjustments.
To adjust the settings:
1. Go to the  DISPLAY menu and highlight  Color Management .
2. Press  MODE/ENTER on the projector or  ENTER on the remote control  and the 
Color Management  page is displayed.
3. Highlight  Primary Color and press  /  to select a color from among Red, Yellow, 
Green, Cyan, Blue, or Magenta.
4. Press  to highlight  Hue and press  /  to select its range. Increase in the range 
will include colors consisted of more  proportions of its two adjacent colors.
Please refer to the illustration to the right for 
how the colors relate to each other.
For example, if you select Red and set its 
range at 0, only pure red in the projected 
picture will be select ed. Increasing its range 
will include red close to yellow and red close 
to magenta.
5. Press  to highlight  Saturation and adjust 
its values to your preference by pressing  / . Every adjustment made will reflect to the 
image immediately.
For example, if you select Red and set its 
value at 0, only the saturation of pure red will 
be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less 
saturated colors; a setting of “0” removes that  color from the image entirely. If the saturation 
is too high, that color will be overpowering and unrealistic.
6. Press   to highlight  Gain and adjust its values to your preference by pressing  / . 
The contrast level of the primary color you  select will be affected. Every adjustment 
made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press  MENU/EXIT  on the projector or  Exit on the remote control to exit and save the 
settings.
RED
BLUEGREEN
Yellow
Cyan
Magenta 
						

							
Operation 35
Hiding the image
In order to draw the audiences full attention to the 
presenter, you can use   on the projector or Blank 
on the remote control to hide the screen image. Press 
any key on the projector or remote control to restore 
the image.  The word  BLANK appears at the lower 
right corner of the screen while the image is hidden.
You can set the blank time in the 
SYSTEM SETUP: 
Basic > Blank Timer  menu to let the projector 
return the image automatically after a period of time 
when there is no action taken on the blank screen. 
CAUTION
Do not block the projection le ns from projecting as this 
could cause the blocking object to become heated and 
deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked , you can prevent your projector settings from 
being changed accidentally (by ch ildren, for example). When the Panel Key Lock  is on, no 
control keys on the projector will operate except  POWER.
1. Press   on the projector or remote control, or  go to the 
SYSTEM SETUP: Basic > Panel 
Key Lock menu
, and select  On by pressing 
/  on the projector or remote control. 
2. A confirmation message is displayed. Select  Yes to confirm.
To release panel key lock, press and hold   for 3 
seconds on the projector.
You can also use the remote control to enter the 
SYSTEM SETUP: Basic  > Panel Key Lock  menu 
and press  /  to select  Off.
• Keys on the remote control are still functional 
when panel key lock is enabled.
• If you press  POWER to turn off the projector  without disabling panel key lock, the projector will 
still be in locked status the next time it is turned 
on.
II
II 
						

							
Operation
36
Freezing the image
Press  Freeze  on the remote control to freeze the 
image. The word  FREEZE will be displayed in the 
upper left corner of the screen.  To release the 
function, press any key on the projector or remote 
control.
Even if an image is frozen on the screen, the pictures 
are running on the video or other device. If the 
connected devices have act ive audio output, you will 
still hear the audio even though the image is frozen on 
screen.
Operating in a high altitude environment
We recommend you use the  High Altitude Mode when your environment is between 1500 
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature 
is between 0°C and 35°C. The projector will be  over cooled, if you turn the mode on under 
such a condition.
To activate the  High Altitude Mode :
1. Press  MENU/EXIT  on the projector or  Menu on 
the remote control and then press  /  until 
the  SYSTEM SETUP: Advanced  menu is 
highlighted.
2. Press  to highlight  High Altitude Mode and 
press /  to select  On. A confirmation 
message is displayed.
3. Highlight  Yes and press  MODE/ENTER  on the projector or  ENTER on the remote 
control.
Operation under  High Altitude Mode may cause a higher decibel operating noise level 
because of increased fan speed necessary  to improve overall system cooling and 
performance.
If you use this projector under other extreme conditions excluding the above, it may display 
auto shut-down symptoms, which is designed to  protect your projector from over-heating. 
In cases like this, you should switch to  High Altitude Mode to solve these symptoms. 
However, this is not to state that this pr ojector can operate under any and all harsh or 
extreme conditions.
We recommend you use the High Altitude 
mode by selecting it whenever your 
environment is higher than 1500 m.
Do you want to turn High Altitude Mode 
ON?
Yes NoNotice