ViewSonic Pjd6243 Projector User Manual

24 Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range, hue, saturation and gain according
to your preference.
White Intensity
Increase the brightness...

25 H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Zoom
Zoom in and out the images.
Video Setting
Allow you to enter the Video Setting menu.
• Sharpness: Sharpen or soften the image.
• Tint: Shift colors toward red or green.
• Saturation: Adjust a video image from black and white to fully saturated color.
Audio Setting
Allow you to enter the Audio Setting menu.
• Volume:...

26 Start up Screen
Allow you to enter the Start up Screen menu.
• Start up Screen: Select start up screen when the projector is powered on or when 
no signal is input. "User" is the screen that you captured.
• Screen Capture: Capture the current projection screen as a start up screen.
• Screen Capture Delete: Delete the captured projection screen.
Message
Enable or disable the message box at the right bottom of the screen.
Auto Source
Automatically scan through all the input source.
Power Saving...

27 • Apply: Save and execute the wired LAN settings.
Option
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2 or OFF.
DCR (Dynamic Contrast Ratio)
Enable DCR will further enhance contrast ratio by darkening the black scenes.
Disable DCR will resume to normal contrast performance. DCR will impact lamp life
and system noise performance.
Password
Set, change or delete the password. When the password function is added, image...

28
Information
Input Source
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal  frequency.
V. Frequency
Display current image vertical frequency.
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Mac Address
Abbreviation for Media Access Control Address. Mac Address is a unique ID number
assigned to each network adapter.
Controlling the projector through a LAN environment
The projector supports Crestron®...

29 6. Please wait for around 15 - 20 seconds, and then re-enter the Lan control setting
page. The IP address,Subnet Mask,Default Gateway, and DNSsettings will be
displayed. Note down the IP address displayed in the IP address row.
Important
• If the Projector IP Address still does not appear, contact your network administrator.
• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default 
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly 
connected...

30 2. The main page of the Network Control appears.
•Accessing to Network Settings or Email Alert page requires Administrator password. The
default password is 0000.
3. This page allows you to make adjustments to the AMX and SNMP settings. In the
AMX device discover row, when ON is selected, the projector can be detected by
controllers of AMX connected to the same network. For the Details of AMX Device
Discovery, visit the AMX web site at http://www.amx.com/.
4. If your projector is connected to a...

31 Please pay attention to the limitation of input length (including space and other
punctuation keys) in the list blow:
• / > < $ % +  ' " are prohibited. 
About Crestron e-Control®
1. The Crestron e-Control
® page provides a variety of virtual keys to control the
projector or adjust the projected pictures. 
Category ItemInput-LengthMaximum Number of Characters
Network SettingsNetworkDHCP/Manual (N/A)
IP Address XXX.XXX.XXX.XXX
Subnet Mask XXX.XXX.XXX.XXX
GatewayXXX.XXX.XXX.XXX
DNS Server...

32 i. These buttons function the same as the ones on the OSD menus or remote 
control.
ii. To switch input source, click on your desired signal.
Important
• The Menu button can also be used to go back to previous OSD menu, exit and save 
menu settings.
• The source list varies according to the connectors available on the projector.
• When you use the projector control panel or remote control to change the OSD menu 
settings, it may take a while for the web browser to synchronize these changes with the...

33 3. The info page displays the information and status of this projector.
i. Press exit to go back to the Crestron remote network operation page.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in
the upper right corner of the screen. You will be able to deliver messages to
RoomView™ software administrators/users who connect to the same local area
network.
• For more information, visit http://www.crestron.com &www.crestron.com/getroomview.
Crestron RoomView
On the “Edit...