ViewSonic Pjd6243 Projector User Manual

4
Bottom View
1. Security bar 
2. Ceiling mount holes
3. Ventilation holes
Note
• This projector can be used with a ceiling mount for support. The ceiling mount is not 
included in the package.
• Contact your dealer for information to mount the projector on a ceiling.
1
2
3 

5
Using the product
Control panel
1. Power
Turn the projector on or off.
2. SOURCE
Display the source selection bar.
3. MENU/EXIT
Display or exit the on-screen display menus.
4. Keystone/Arrow keys ( /Up,  /Down)
Manually correct distorted images resulting from an angled projection.
5. Four directional buttons
Use four directional buttons to select items or make adjustments to your  selection.
6. MODE
Change the color mode setting by sequence.
7. POWER (Power LED indicator)
Refer to “LED Indicator...

6
Connection ports
1. AUDIO IN
Connect an audio output from video equipment or computer to this jack.
2. HDMI
Connect HDMI output from video equipment to this jack.
3. S-VIDEO
Connect S-Video output from video equipment to this jack.
4. COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
5. RS-232
When operating the projector via a computer, connect this to the controlling com-
puter's RS-232C port.
6. MINI USB
This connector is for firmware update and mouse function...

7
Remote control
1. Power
Turn the projector on or off.
2. VGA1
Display COMPUTER IN 1 signal.
3. Aspect
Select the display aspect ratio.
4. Keystone/Arrow keys ( /Up,  /
Down)
Manually correct distorted images
resulting from an angled projection.
5. Left
When the On-Screen Display
(OSD) menu is activated, the #4,
#5, and #20 keys are used as direc-
tional arrows to select the desired
menu items and to make adjust-
ments.
6. My Button
User definable key for customized
function.
7. Menu
Display on-screen...

8 22. Page Up
Perform page up function when
mouse mode is activated.
23. Page Down
Perform page down function when
mouse mode is activated.
24. Magnify
Magnifies or reduces the projected
picture size.25. Volume
Adjust the volume level.
26. Mute
Cut off the sound temporarily.
27. Color Mode
Select the picture setup mode.
28. Timer
Activate P-Timer OSD menu.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more flex-
ibility when delivering...

9
Installing the Batteries
1. Open the battery cover in the 
direction shown.
2. Install batteries as indicated by the 
diagram inside the compartment.
3. Close the battery cover into position.
Caution
•  Risk of explosion if battery is replaced by an incorrect type.
•  Dispose of used batteries according to the instructions.
•  Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
• Keep the battery out of the reach of children. 
• Remove batteries from remote control...

10
Remote control operation
Point the remote control at the infrared remote sensor and press a button.
• Operating the projector from the 
front.
Note
• The remote control may not operate when there is sunlight or other strong light such as 
a fluorescent lamp shining on the remote sensor.
• Operate the remote control from a position where the remote sensor is visible.
• Do not drop the remote control or jolt it.
• Keep the remote control out of locations with excessively high temperature or humidity.
•...

11
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Important
• In the connections shown above, some cables may not be included with the projector 
(see "Package contents" on page 2). They are commercially available from electronics 
stores.
• The connection illustrations above are for reference only. The rear connecting jacks...

12
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM
® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of
the computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal...

13
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one
of the following output sockets:
•HDMI
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the
above!connecting methods, however each provides a different level of video quality.
The method!you choose will most likely depend upon the availability of matching ter-
minals on both the!projector and the Video source...