ViewSonic Pjd6221 Projector User Manual

 EN-18
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings. 

EN-19
 
1 Adjustable range and default setting vary depending on signal type.
2 This function is only available when the projector is installed an optional filter cover. 

 EN-20
How to operate
1. Press the MENU  button to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3.After selecting the desired main menu item, press X to enter sub-menu for
feature setting.
4. Use S / T to select the desired item and adjust the settings with W / X.
5. Press the MENU button, the screen will return to the main menu.
6. To exit OSD, Press the MENU button again. The OSD menu will close and the
projector will automatically save the new...

EN-21
GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
3D Sync
„On: 120Hz detection 
„Off: Disable 120Hz
3D Sync Invert
„On: Invert left and right frame contents.
„Off: Default frame contents.
Computer Image (Computer Mode)
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection...

 EN-22
Menu Position
Choose the menu location on the display screen.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Signal Type
Specify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to
project.
„Auto : Automatically detect the input signal type from COMPUTER IN 1 and 
COMPUTER IN 2 terminals.
„RGB : For VGA signal
„YCbCr/YPbPr:For component signal
Lamp...

EN-23
Option (Computer / Video Mode)
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Password
Set or change the password. When the password function is added, image projection
will require to input the preset password when turning on the projector.
Screen Capture
Capture the current projection screen as a start-up screen.
Start-up Screen
Select start-up screen when the projector is powered on or when no signal is input.
User is the screen that you...

 EN-24
an IP address from server even if DHCP is “Yes”.
Group Name
Display group name.
Projector  Name
Display projectors model name.
IP Address
Numerical address to identify networked computers. This function can only be used
when DHCP is set to No.
„The IP Address is the number that identifies this projector on the network. You 
cannot have two devices with the same IP Address on the same network.
„The IP Address “0.0.0.0” is prohibited.
Subnet Mask
A numeric value to define the number of bits used...

EN-25
Network Control
This feature provides the ability to remotely control and manage the projector through
the network.
Preparation:
1. Connect one end of the internet cable to the Network Control connector on the projector.
2. Connect the other end of the internet cable to an available RJ-45 connector on  your computer.
3. Turn on your projector and computer.
There are two ways to connect to the network control:A. Auto IP address setting (DHCP : Yes):
1. Enable DHCP from the projector OSD, under...

 EN-26
2. Start browser in PC and specify following URL, then click “Go” button.
„URL: http://(Projector IP address)/
„For example, if projector IP address is 169.254.1.1, specify URL: http://
169.254.1.1/
3. If connection succeeds, the login screen is displayed. Enter your User name and  Password and click “OK”. Below are the factory default settings for administrator, 
user and passwords.
)For setting passwords, please go to Network Control page > Password.
Item User name Password
Administrator Admin...

EN-27
B. Manual IP address setting (DHCP: No):
1. Set IP Address and Subnet Mask under Network Config.
„IP Address: Numerical address to identify networked computers.
„Subnet Mask: A numeric value to define the number of bits used for a 
network address of a divided network (or subnet) in an IP Address.
„Gateway: A server (or router) to communicate across networks (subnets) 
that are divided by Subnet Mask.
2. From your computer, go to Start > Settings > Network and Dial-up 
Connections > Local Area...