ViewSonic Pjd6221 Projector User Manual

							
 EN-18
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings. 
						

							
EN-19
 
1 Adjustable range and default setting vary depending on signal type.
2 This function is only available when the projector is installed an optional filter cover. 
						

							
 EN-20
How to operate
1. Press the MENU  button to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3.After selecting the desired main menu item, press X to enter sub-menu for
feature setting.
4. Use S / T to select the desired item and adjust the settings with W / X.
5. Press the MENU button, the screen will return to the main menu.
6. To exit OSD, Press the MENU button again. The OSD menu will close and the
projector will automatically save the new settings.
Picture (Computer / Video Mode)
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range and saturation according to your
preference.
Keystone
Manually correct distorted images resulting from an angled projection.
Aspect Ratio
Select how the picture fits on the screen:
„4:3 : The input source will be scaled to fit the projection screen.
„16:9 : The input source will be scaled to fit the width of the screen.
Image
There are many factory presets optimized for various types of images.
„PC : For computer or notebook.
„Movie : For home theater.„sRGB : For PC standard color.
„User : Memorize user’s settings.
„White Board : For white projection screen type.„Black Board : For black projection screen type.
„Green Board: For green projection screen type. 
„Daylight Mode: For a daylight environment.
White Intensity
Increase the brightness of white areas. 
						

							
EN-21
GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
3D Sync
„On: 120Hz detection 
„Off: Disable 120Hz
3D Sync Invert
„On: Invert left and right frame contents.
„Off: Default frame contents.
Computer Image (Computer Mode)
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Video Image (Video Mode)
Saturation
Adjust a video image from black and white to fully saturated color.
Sharpness
Sharpen or soften the image.
Tint
Shift colors toward red or green.
Sound (Computer / Video Mode)
Vo l u m e
Adjust the volume level.
Mute
Cut off the sound temporarily.
Audio 1
Enable or disable Audio 1.
„When Audio 1 is turned on, Audio 2 will turn off automatically.
Audio 2
Enable or disable Audio 2.
„When Audio 2 is turned on, Audio 1 will turn off automatically.
Setting (Computer / Video Mode) 
						

							
 EN-22
Menu Position
Choose the menu location on the display screen.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Signal Type
Specify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to
project.
„Auto : Automatically detect the input signal type from COMPUTER IN 1 and 
COMPUTER IN 2 terminals.
„RGB : For VGA signal
„YCbCr/YPbPr:For component signal
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Lamp Hours Reset
Reset the lamp Hour to 0 hours.
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter
cover.
Filter Hours
Display the filter’s elapsed operating time (in hours).
„When Filter Mode is turned on, the Filter Hours also turns on automatically.
Filter Hours Reset
Reset the filter Hour to 0 hours.
Power Saving
If no operation is performed for a specific period of time, projector will automatically
turn off.
Auto Source
Automatically scan through all the input source.
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life.
„This function will be unavailable when the DCR function is on.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
OSD Timeout
Duration of OSD menu display countly starts (at idle state by second). 
						

							
EN-23
Option (Computer / Video Mode)
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Password
Set or change the password. When the password function is added, image projection
will require to input the preset password when turning on the projector.
Screen Capture
Capture the current projection screen as a start-up screen.
Start-up Screen
Select start-up screen when the projector is powered on or when no signal is input.
User is the screen that you captured.
Zoom
Zoom in and out the images.
Te x t  s h o t
Using command codes, text messages can be sent for display by the projector over a
network connection. Text is shown on the center of the projection screen. This is a
great way to display urgent alert messages to employees, and simply requires a
connection to the projector’s LAN connector.
DCR (Dynamic Contrast Ratio)
Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable
DCR will resume to normal contrast performance. DCR will impact lamp life and
system noise performance.
Closed Caption
Enable or Disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2 or OFF.
Brilliant Color
™             
Produce an expanded on-screen color spectrum that delivers enhanced color
saturation for bright, true-to-life images. Suggesting to turn Off for most video sources
and On for most computer sources. 
NetWork
Enable or disable network management via RJ45 connector.
Network Config (Computer / Video Mode)
DHCP
Abbreviation for Dynamic Host Configuration Protocol. This protocol automatically
assigns IP Address to networked devices.
„When the “DHCP” sets to “Yes”, it takes  some time to obtain IP address from 
DHCP server.
„When the DHCP sets to No, that means user will set IP address by manually.
„Auto IP function will be assigned an IP address if the projector could not obtain  
						

							
 EN-24
an IP address from server even if DHCP is “Yes”.
Group Name
Display group name.
Projector  Name
Display projectors model name.
IP Address
Numerical address to identify networked computers. This function can only be used
when DHCP is set to No.
„The IP Address is the number that identifies this projector on the network. You 
cannot have two devices with the same IP Address on the same network.
„The IP Address “0.0.0.0” is prohibited.
Subnet Mask
A numeric value to define the number of bits used for a network address of a divided
network (or subnet) in an IP Address. This function can only be used when DHCP is
set to No.
„The Subnet Mask “0.0.0.0” is prohibited.
Gateway
A server (or router) to communicate across networks (subnets) that are divided by
Subnet Mask. This function can only be used when DHCP is set to No.
MAC Address
Abbreviation for Media Access Control Address. MAC Address is a unique ID number
assigned to each network adapter. 
Network Restart
Restart network function when the device is not working properly or to apply changes
made on OSD configuration menu. 
Language (Computer / Video Mode)Select the language used by the on-screen menu.
Factory Default (Computer / Video Mode)Restore settings to factory default .
System Info (Computer / Video Mode)
Source
Display the input source.
Resolution
Display the resolution.
H. Frequency
Display H. Frequency.
V. Frequency
Display V. Frequency. 
						

							
EN-25
Network Control
This feature provides the ability to remotely control and manage the projector through
the network.
Preparation:
1. Connect one end of the internet cable to the Network Control connector on the projector.
2. Connect the other end of the internet cable to an available RJ-45 connector on  your computer.
3. Turn on your projector and computer.
There are two ways to connect to the network control:A. Auto IP address setting (DHCP : Yes):
1. Enable DHCP from the projector OSD, under Network Config.
„When DHCP is enabled, IP Address, Subnet Mask and Gateway  
information will get from DHCP server automatically. 
						

							
 EN-26
2. Start browser in PC and specify following URL, then click “Go” button.
„URL: http://(Projector IP address)/
„For example, if projector IP address is 169.254.1.1, specify URL: http://
169.254.1.1/
3. If connection succeeds, the login screen is displayed. Enter your User name and  Password and click “OK”. Below are the factory default settings for administrator, 
user and passwords.
)For setting passwords, please go to Network Control page > Password.
Item User name Password
Administrator Admin  User User  
						

							
EN-27
B. Manual IP address setting (DHCP: No):
1. Set IP Address and Subnet Mask under Network Config.
„IP Address: Numerical address to identify networked computers.
„Subnet Mask: A numeric value to define the number of bits used for a 
network address of a divided network (or subnet) in an IP Address.
„Gateway: A server (or router) to communicate across networks (subnets) 
that are divided by Subnet Mask.
2. From your computer, go to Start > Settings > Network and Dial-up 
Connections > Local Area Connection and right click to select Properties..