ViewSonic Pjd6211p Projector User Manual

 
1 Adjustable range and default setting vary depending on signal type.
2 This function is only available when the projector is installed an optional filter cover.
PJD6211P 
19 
ViewSonic  

How to operate
1. Press the MENU  button to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3.After selecting the desired main menu item, press X to enter sub-menu for
feature setting.
4. Use S / T to select the desired item and adjust the settings with W / X.
5. Press the MENU button, the screen will return to the main menu.
6. To exit OSD, Press the MENU button again. The OSD menu will close and the
projector will automatically save the new settings....

GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
3D Sync
„ Off: Disable 3D function
„ 3D-Vision: For NVIDIA 3D Vision application
„ DLP-LINK: For TI 3D DLP-LINK application
3D Sync Invert (for TI 3D DLP-LINK only)
„On: Invert left and right frame contents.
„Off: Default frame contents.
Computer Image (Computer Mode)
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the...

Signal Type
Specify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to
project.
„Auto : Automatically detect the input signal type from COMPUTER IN 1 and 
COMPUTER IN 2 terminals.
„RGB : For VGA signal
„YCbCr/YPbPr:For component signal
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Lamp Hours Reset
Reset the lamp Hour to 0 hours.
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter
cover.
Filter Hours
Display the...

Set or change the password. When the password function is added, image projection
will require to input the preset password when turning on the projector.
Screen Capture
Capture the current projection screen as a start-up screen.
Screen Capture Delete
Delete the captured projection screen.
Start-up Screen
Select start-up screen when the projector is powered on or when no signal is input.
User is the screen that you captured.
Zoom
Zoom in and out the images.
DCR (Dynamic Contrast Ratio)
Enable DCR will...

Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.Warning
Never open any of the covers on the projector. Dangerous electrical voltages
inside the projector can cause severe injury. Do not attempt to service this
product...

Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp is extremely hot right after turning off the projector. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait for at least 
45 minutes...

1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try  reinstalling the lamp.
9....

Specifications
Display system Single 0.55 DLP panel
Resolution XGA (1024 × 768)
Zoom 1.1X
F/No. 2.51 - 2.69
Focal length 21.95 - 24.18mm
Screen size 27” – 300”
Lamp 180W
Input terminal D-Sub 15-pin x 2, S-VIDEO x 1, VIDEO x 1, Audio signal input (3.5 mm stereo mini jack) x 1
Output terminal D-Sub 15 pin x 1,  Audio si gnal output (3.5 mm stereo mini jack) x 
1
Control terminal RS-232 x 1, USB x 1
Speaker 2 watt x 1
Video compatibility NTSC, NTSC 4.43 PAL, PAL-N, PAL M
SECAM, HDTV (480p, 576p, 720p,...

Appendix
LED Indicator Messages
LED Type Color Status MeaningPower  LEDBlueFlashThe projector is  in standby 
mode.Lamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueSolidPowering upLamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueSolidNormal operationLamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueFlashPower-downLamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueSolidThe projector system has some 
problems with its fans, so the 
projector cannot start up. Lamp LEDRedSolidTe m p  L E D...