ViewSonic Pjd6211p Projector User Manual

							
 
1 Adjustable range and default setting vary depending on signal type.
2 This function is only available when the projector is installed an optional filter cover.
PJD6211P 
19 
ViewSonic  
						

							
How to operate
1. Press the MENU  button to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3.After selecting the desired main menu item, press X to enter sub-menu for
feature setting.
4. Use S / T to select the desired item and adjust the settings with W / X.
5. Press the MENU button, the screen will return to the main menu.
6. To exit OSD, Press the MENU button again. The OSD menu will close and the
projector will automatically save the new settings.
Picture (Computer / Video Mode)
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range and saturation according to your
preference.
Keystone
Manually correct distorted images resulting from an angled projection.
Aspect Ratio
Select how the picture fits on the screen:
„4:3 : The input source will be scaled to fit the projection screen.
„16:9 : The input source will be scaled to fit the width of the screen.
Image
There are many factory presets optimized for various types of images.
„PC : For computer or notebook.
„Movie : For home theater.„ViewMatch : For PC standard color.
„User : Memorize user’s settings.
„White Board : For white projection screen type.„Black Board : For black projection screen type.
„Green Board: For green projection screen type. 
„Brightest : For a daylight environment.
White Intensity
Increase the brightness of white areas.
PJD6211P 
20 
ViewSonic  
						

							
GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
3D Sync
„ Off: Disable 3D function
„ 3D-Vision: For NVIDIA 3D Vision application
„ DLP-LINK: For TI 3D DLP-LINK application
3D Sync Invert (for TI 3D DLP-LINK only)
„On: Invert left and right frame contents.
„Off: Default frame contents.
Computer Image (Computer Mode)
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Video Image (Video Mode)
Color
Adjust a video image from black and white to fully saturated color.
Sharpness
Sharpen or soften the image.
Tint
Shift colors toward red or green.
Sound (Computer / Video Mode)
Vo l u m e
Adjust the volume level.
Mute
Cut off the sound temporarily.
Setting (Computer / Video Mode)
Menu Position
Choose the menu location on the display screen.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
PJD6211P 
21 
ViewSonic  
						

							
Signal Type
Specify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to
project.
„Auto : Automatically detect the input signal type from COMPUTER IN 1 and 
COMPUTER IN 2 terminals.
„RGB : For VGA signal
„YCbCr/YPbPr:For component signal
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Lamp Hours Reset
Reset the lamp Hour to 0 hours.
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter
cover.
Filter Hours
Display the filter’s elapsed operating time (in hours).
„When Filter Mode is turned on, the Filter Hours also turns on automatically.
Filter Hours Reset
Reset the filter Hour to 0 hours.
Power Saving
If no operation is performed for a specific period of time, projector will automatically
turn off.
Auto Source
Automatically scan through all the input source.
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life.
„This function will be unavailable when the DCR function is on.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
OSD Timeout
Duration of OSD menu display countly starts (at idle state by second).
Option (Computer / Video Mode)
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Password
PJD6211P 
22 
ViewSonic  
						

							
Set or change the password. When the password function is added, image projection
will require to input the preset password when turning on the projector.
Screen Capture
Capture the current projection screen as a start-up screen.
Screen Capture Delete
Delete the captured projection screen.
Start-up Screen
Select start-up screen when the projector is powered on or when no signal is input.
User is the screen that you captured.
Zoom
Zoom in and out the images.
DCR (Dynamic Contrast Ratio)
Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable
DCR will resume to normal contrast performance. DCR will impact lamp life and
system noise performance.
Closed Caption
Enable or Disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2 or OFF.
Brilliant Color
™             
Produce an expanded on-screen color spectrum that delivers enhanced color
saturation for bright, true-to-life images. Suggesting to turn Off for most video sources
and On for most computer sources. 
Green Mode
Enable this function when power consumption is under 1W.
Message
Enable or disable the message box at the right bottom of the screen.
Language (Computer / Video Mode)Select the language used by the on-screen menu.
Factory Default (Computer / Video Mode)Restore settings to factory default .
System Info (Computer / Video Mode)
SourceDisplay the current input source.
ResolutionDisplay current input source resolution.
H. FrequencyDisplay current image horizontal  frequency.
V. FrequencyDisplay current image vertical frequency.
PJD6211P 
23 
ViewSonic  
						

							
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.Warning
Never open any of the covers on the projector. Dangerous electrical voltages
inside the projector can cause severe injury. Do not attempt to service this
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Cleaning the Filter Cover
The filter cover, which is located at the side of the projector, should be cleaned after
every 100 hours of use. If it is not cleaned periodically, it can become clogged with
dust and prevent the projector from being ventilated properly. This can cause over
heating and damage the projector.
To clean the filter cover:1. Switch the projector off and unplug the AC power cord from the wall socket.
2. Remove the filter cover as the illustration  shown.
3. Clean the filter cover.
„To clean the filter cover, you are 
advised to use a small vacuum 
cleaner designed for computers and 
other office equipment.
„If the filter cover is torn, replace it.4. Replace the filter cover.
5. Attach the filter cover.  
6. Plug the power back into the projector.
„Turn off the projector and remove the AC power cord from the power outlet 
before beginning maintenance work.
„Make sure the lens is cool before cleaning.„Do not use detergents or chemicals other than those noted above. Do not use 
benzene or thinners.
„Do not use chemical sprays.„Use a soft cloth or lens paper only.
PJD6211P 
24 
ViewSonic  
						

							
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp is extremely hot right after turning off the projector. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait for at least 
45 minutes for the lamp to cool down.
„Do not touch the lamp glass at any time. The lamp may explode due to 
improper handling, including the touching of the lamp glass.
„Lamp lifetime may differ from lamp to lamp and according to the environment 
of use. There is no guarantee of the same lifetime for each lamp. Some lamps 
may fail or terminate their lifetime in a shorter period of time than other similar 
lamps.
„A lamp may explode as a result of vibration, shock or degradation as a result of 
hours of use as its lifetime draws to an end. Risk of explosion may differ 
according to the environment or conditions in which the projector and lamp are 
being used.
„Wear protective gloves and eyeglasses when fixing or detaching the lamp.„Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least 
for 5 minutes to turn off the projector after powering on.
„Do not operate the lamp in proximity to paper, cloth, or other combustible 
material nor cover it with such materials.
„Do not operate the lamp in an atmosphere containing an inflammable 
substance, such as thinner.
„Thoroughly ventilate the area or the room when operating the lamp in an 
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, 
nausea, dizziness, and other symptoms.
„The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury 
inside the lamp will be exposed. Leave the area immediately if the lamp 
shatters while being operated and ventilate the area for at least 30 minutes in 
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to 
user’s health.
PJD6211P 
25 
ViewSonic  
						

							
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try  reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Setting” menu.
„Dispose the used lamp according to local regulations.„Ensure that screws are tightened properly. Screws not tightened fully may 
result in injury or accidents.
„Since the lamp is made of glass, do not drop the unit and do not scratch the 
glass.
„Do not reuse the old lamp. This could cause the lamp to explode.„Be sure to turn off the projector and unplug the AC power cord before 
replacing the lamp.
„Do not use the projector with the lamp cover removed.
PJD6211P 
26 
ViewSonic  
						

							
Specifications
Display system Single 0.55 DLP panel
Resolution XGA (1024 × 768)
Zoom 1.1X
F/No. 2.51 - 2.69
Focal length 21.95 - 24.18mm
Screen size 27” – 300”
Lamp 180W
Input terminal D-Sub 15-pin x 2, S-VIDEO x 1, VIDEO x 1, Audio signal input (3.5 mm stereo mini jack) x 1
Output terminal D-Sub 15 pin x 1,  Audio si gnal output (3.5 mm stereo mini jack) x 
1
Control terminal RS-232 x 1, USB x 1
Speaker 2 watt x 1
Video compatibility NTSC, NTSC 4.43 PAL, PAL-N, PAL M
SECAM, HDTV (480p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency 31 - 100 KHz
50 - 120 Hz
Environment Operating: Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power requirement AC 100-240 V, 50 - 60 Hz, 2.5A
Power consumption 235W (typical), 
						

							
Appendix
LED Indicator Messages
LED Type Color Status MeaningPower  LEDBlueFlashThe projector is  in standby 
mode.Lamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueSolidPowering upLamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueSolidNormal operationLamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueFlashPower-downLamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueSolidThe projector system has some 
problems with its fans, so the 
projector cannot start up. Lamp LEDRedSolidTe m p  L E D  RedFlashPower  LEDBlueFlashThe lamp is in good condition 
and is projecting at maximum 
brightness. Lamp LEDRed Off Te m p  L E D  Red Off Power  LEDBlueSolidThe lamp has reached its end 
of life and must be changed 
soon. The lamp will continue to 
operate until it fails . Change 
the lamp. If the lamp is off, then  
the ballast will become 
malfunction. Lamp LEDRed SolidTe m p  L E D  Red Off
Power  LEDBlueSolidThe projector is shutting and 
the fan motor is cooling the 
lamp for shutdown. Do not 
unplug the power cord or turn 
the power off before the Lamp 
LED changes to flashing. The 
fan motor will turn off when the 
lamp has cooled. Lamp LEDRedFlashTe m p  L E D  RedOff
Power  LEDBlueSolidTemperature is too high. The 
lamp will turn off. The fan motor 
is cooling the lamp. Lamp LEDRedFlashTe m p  L E D  RedOff Power  LEDBlue Off The lamp ignition failed. If 
temperature is too high, the 
fans will cool the lamp.Lamp LEDRedSolidTe m p  L E D  RedSolid
PJD6211P 
28 
ViewSonic