ViewSonic Pjd5211 Projector User Manual

							
Operation
28 2. Press
  to highlight 
Aspect Ratio .
3. Press  /  to select an aspect ratio to  suit the format of the video signal and your 
display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active 
areas. OSD menus can be displayed on those unused black areas.
1. Auto: Scales an image proportionally to fit the 
projectors native reso lution in its horizontal 
width. This is suitable for the incoming image 
which is neither in 4:3 nor 16:9 and you want to 
make most use of the screen without altering the 
images aspect ratio.
2. 4:3: Scales an image so that it is displayed in the 
center of the screen with a 4:3 aspect ratio. This 
is most suitable for 4:3 images like computer 
monitors, standard definition TV and 4:3 aspect 
DVD movies, as it displays  them without aspect 
alteration.
3. 16:9: Scales an image so that it is displayed in 
the center of the screen with a 16:9 aspect ratio. 
This is most suitable for images which are 
already in a 16:9 aspect , like high definition TV, 
as it displays them wi thout aspect alteration.
16:10 picture
15:9 picture
4:3 picture
16:9 picture 
						

							
Operation 29
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined 
picture modes so that you can choose one to suit 
your operating environment and input signal 
picture type.
To select an operation mode that suits your need, 
you can follow one of the following steps.
• Press  MODE/ENTER  on the projector or 
Color Mode  on the remote control repeatedly 
until your desired mode is selected.
•Go to the  PICTURE > Color Mode  menu and press  /  to select a desired mode.
Picture modes for different types of signals
The picture modes available for differen t types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1. Brightest mode : Maximizes the brightness of the projected image. This mode is 
suitable for environments where extra-high  brightness is required, such as using the 
projector in well lit rooms.
2. Daylight mode : Is designed for presentations unde r daylight environment to match 
PC and notebook coloring.
3. ViewMatch mode : Switch in between high brightness performance or Accuracy 
color performance.
4. Cinema mode :  Is appropriate for playing colorful  movies, video clips from digital 
cameras or DVs through the PC input for best  viewing in a blackened (little light) 
environment.
5. User 1/User 2 mode : Recalls the settings customized  based on the current available 
picture modes. See  Setting the User 1/User 2 mode on page 30  for details.
Video input signals: S-Video, Vi deo, D-Sub / Comp. 1/2 (YPbPr)
1. Brightest mode : Optimized for daylight viewing,  with living room level ambient 
brightness.
2. Gaming mode : Suitable for all types of entert ainment media, including gaming and 
movies.
3. ViewMatch mode : Switch in between high brightness performance or Accuracy color 
performance.
4. Cinema mode : Is suitable for enjoying dark movies  or DVD movies best viewed in a 
blackened (little light) home cine ma or lounge room environment.
5. User 1/User 2 mode : Recalls the settings customized  based on the current available 
picture modes. See  Setting the User 1/User 2 mode on page 30  for details. 
						

							
Operation
30
Setting the User 1/User 2 mode
There are two user-definable modes if the curre nt available picture modes are not suitable 
for your need. You can use one of the picture modes (except the  User 1/User 2 ) as a starting 
point and customize the settings.
1. Press  MENU/EXIT  on the projector or  MENU on the remote control to open the On-
Screen Display (OSD) menu.
2. Go to the  PICTURE > Color Mode  menu.
3. Press /  to select  User 1 or User 2 .
4. Press   to highlight  Reference Mode .
This function is only available when User 1 or User 2 mode is selected up in the Color Mode 
sub-menu item.
5. Press  /  to select a picture mode  that is closest to your need.
6. Press   to select a sub-menu item to be changed and adjust the value with  / . 
See  Fine-tuning the image quality in user modes  below for details.
7. When all settings have been done, highlight  Save Settings and press MODE/ENTER  
on the projector or  Enter on the remote control to store the settings.
8. The confirmation message  Setting Saved is displayed.
Using Screen Color
In the situation where you are projecting onto a  colored surface such as a painted wall which 
may not be white, the  Screen Color feature can help correct the  projected picture’s colors to 
prevent possible color difference between  the source and projected pictures.
To use this function, go to the  DISPLAY > Screen Color  menu and press  /  to select a 
color which is closest to the color of the pr ojection surface. There are several precalibrated 
colors to choose from:  Whiteboard, Greenboard , and Blackboard .
This function is only available when a PC type input signal is selected.
Fine-tuning the image qu ality in user modes
According to the detected signal type, there  are some user-definable functions available 
when  User 1  or User 2  mode is selected. You can make adjustments to these functions 
based on your needs.
Adjusting Brightness
Highlight the  PICTURE > Brightness  menu and press  / .
The higher the value, the br ighter the image. And the 
lower the setting, the darker  the image. Adjust this 
control so the black areas of the image appear just as 
black and that detail in  the dark areas is visible.
Adjusting Contrast
Highlight the  PICTURE > Contrast  menu and press  / .
The higher the value, the great er the contrast. Use this 
to set the peak white level after you have previously 
adjusted the  Brightness setting to suit your selected 
input and viewing environment.
+50+30 +70
0-30+30 
						

							
Operation 31
Adjusting Color
Highlight the PICTURE > Color  menu and press  / .
Lower setting produces less saturated colors. If  the setting is too high, colors on the image 
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the  PICTURE > Tint  menu and press  / .
The higher the value, the more reddish the pict ure becomes. The lower the value, the more 
greenish the picture becomes.
Adjusting Sharpness
Highlight the  PICTURE > Sharpness  menu and press  / .
The higher the value, the sharper the picture b ecomes. The lower the value, the softer the 
picture becomes.
Adjusting Brilliant Color
Highlight the  PICTURE > Brilliant Color  menu and press  / .
This feature utilizes a new co lor-processing algorithm and system level enhancements to 
enable higher brightness while providing truer,  more vibrant colors in the projected picture. 
It enables a greater than 50% brightness incr ease in mid-tone images, which are common in 
video and natural scenes, so the projector reprodu ces images in realistic and true colors. If 
you prefer images with that quality, select  On. If you don’t need it, select  Off.
When  Off is selected, the  Color Temperature  function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature  menu and press  / .
The options available for color temperature*  settings vary according to the signal type 
selected.
1. T1: With the highest color temperature, T1  makes the image appear the most bluish 
white than other settings.
2. T2: Makes images appear bluish white.
3. T3: Maintains normal colorings for white.
4. T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are cons idered to be white for various purposes. One 
of the common methods of representing white co lor is known as the “color temperature”. A 
white color with a low color temperature appear s to be reddish white. A white color with a 
high color temperature appears to have more blue in it. 
						

							
Operation
32
Color Management
Only in permanent installations with controlled  lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allo w for more accurate color reproduction, should 
you require it.
If you have purchased a test disc which contains  various color test patterns and can be used 
to test the color presentation on monitors, TV s, projectors, etc., you can project any image 
from the disc on the screen and enter the  Color Management menu to make adjustments.
To adjust the settings:
1. Go to the  DISPLAY menu and highlight  Color Management .
2. Press  MODE/ENTER  on the projector or  Enter on the remote control  and the  Color 
Management  page is displayed.
3. Highlight  Primary Color and press  /  to select a color from among Red, Yellow, 
Green, Cyan, Blue, or Magenta.
4. Press  to highlight  Hue and press  /  to select its range. Increase in the range 
will include colors consisted of more  proportions of its two adjacent colors.
Please refer to the illustration to the 
right for how the colors relate to each 
other.
For example, if you select Red and set its 
range at 0, only pure red in the projected 
picture will be selected. Increasing its range 
will include red close to yellow and red close 
to magenta.
5. Press  to highlight  Saturation and adjust 
its values to your preference by pressing  / . Every adjustment made will reflect to the 
image immediately.
For example, if you select Red and set its  value at 0, only the saturation of pure red 
will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less 
saturated colors; a setting of “0” removes that  color from the image entirely. If the saturation 
is too high, that color will be overpowering and unrealistic.
6. Press   to highlight  Gain and adjust its values to your preference by pressing  / . 
The contrast level of the primary color you  select will be affected. Every adjustment 
made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press  MENU/EXIT  on the projector or  Exit on the remote control to exit and save the 
settings.
RED
BLUEGREEN
Yellow
Cyan
Magenta 
						

							
Operation 33
Hiding the image
In order to draw the audiences full attention to the 
presenter, you can use   on the projector or Blank 
on the remote control to hide the screen image. Press 
any key on the projector or remote control to restore 
the image.  The word  BLANK appears at the lower 
right corner of the screen while the image is hidden.
You can set the blank time in the 
SYSTEM SETUP: 
Basic > Blank Timer  menu to let the projector 
return the image automatically after a period of time 
when there is no action taken on the blank screen. 
Once Blank is pressed, the projector enters Economic mode automatically.
CAUTION
Do not block the projection lens from projecti ng as this could cause the blocking object to 
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked , you can prevent your projector settings from 
being changed accidentally (by ch ildren, for example). When the Panel Key Lock is on, no 
control keys on the projector will operate except  POWER.
1. Press   on the projector or go to the 
SYSTEM SETUP: Basic > Panel Key 
Lock  menu
, and select  On by pressing  /  
on the projector or remote control. 
2. A confirmation message is displayed. Select  Yes to confirm.
To release panel key lock, press and hold   for 3 
seconds on the projector.
You can also use the remote control to enter the  SYSTEM SETUP: Basic > Panel Key 
Lock  and press  /  to select  Off.
• Keys on the remote control are still functional when panel key lock is enabled.
• If you press  POWER to turn off the projec tor without disabling panel key lock, the 
projector will still be in locked status the next time it is turned on.
II
II 
						

							
Operation
34
Freezing the image
Press  Freeze  on the remote control to freeze the 
image. The word  FREEZE will be displayed in the 
upper left corner of the screen.  To release the 
function, press any key on the projector or remote 
control.
Even if an image is frozen on the screen, the pictures 
are running on the video or other device. If the 
connected devices have act ive audio output, you will 
still hear the audio even though the image is frozen on 
screen.
Operating in a high altitude environment
We recommend you use the  High Altitude Mode when your environment is between 1500 
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature 
is between 0°C and 35°C. The projector will be  over cooled, if you turn the mode on under 
such a condition.
To activate the  High Altitude Mode :
1. Press  MENU/EXIT  on the projector or  MENU 
on the remote control and then press  /  until 
the  SYSTEM SETUP: Advanced  menu is 
highlighted.
2. Press  to highlight  High Altitude Mode and 
press /  to select  On. A confirmation 
message is displayed.
3. Highlight  Yes and press  MODE/ENTER  on the projector or  Enter on the remote 
control.
Operation under  High Altitude Mode  may cause a higher decibel operating noise level 
because of increased fan speed necessary  to improve overall system cooling and 
performance.
If you use this projector under other extreme  conditions excluding the above, it may display 
auto shut-down symptoms, which is designed to  protect your projector from over-heating. 
In cases like this, you should switch to  High Altitude Mode to solve these symptoms. 
However, this is not to state that this pr ojector can operate under any and all harsh or 
extreme conditions.
We recommend you use the High Altitude 
mode by selecting it whenever your 
environment is higher than 1500 m.
Do you want to turn High Altitude Mode 
ON?
Yes NoNotice 
						

							
Operation 35
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The 
following settings do not affect the projection settings, operation, or performance.
• Menu Display Time  in the SYSTEM SETUP: Advanced  > Menu Settings  menu sets 
the length of time the OSD will remain activ e after your last key press. The time length 
ranges from 5 to 30 seconds in 5-second incr ements. Use  /  to select a suitable time 
frame.
• Menu Position  in the SYSTEM SETUP: Advanced  > Menu Settings  menu sets the 
OSD position in five locations. Use  /  to select a preferred position.
• Language  in the SYSTEM SETUP: Basic  menu sets your familiar language for the 
OSD menus. Use  /  to select your language.
• Splash Screen  in the SYSTEM SETUP: Basic  menu sets a preferred logo screen to be 
displayed during projector start- up. Use  /  to select a screen.
Shutting down the projector
1. Press POWER and a confirmation message 
is displayed prompting you. 
If you dont respond in a few seconds, the 
message will disappear.
2. Press  POWER a second time. The 
POWER indicator light  flashes blue, the 
projection lamp shuts down, and the fans will 
continue to run for approximately 90 seconds 
to cool down the projector.
3. Disconnect the power cord from the wall  socket if the projector wi ll not be used in an 
extended period of time.
CAUTION
• To protect the lamp, the projector will not respond  to any commands during the cooling process.
• To shorten the cooling time, you can also activate  the Quick Cooling function. See  Quick Cooling on page 40 for details.
• Do not unplug the power cord before the projector shutdown sequence is complete or  during the 90-second cooling down process.
• If the projector is not properly shut down, to protect the lamp, when you attempt to re-start  the projector, the fans will run for a few minutes to cool down. Press  POWER again to 
start the projector after the fans stop and the POWER indicator light flashes blue.
II
II
II 
						

							
Operation
36
Menu operation
Menu system
Please note that the on-screen display (OSD ) menus vary according to the signal type 
selected.
The menu items are available when the projector  detects at least one valid signal. If there is 
no equipment connected to the projector or no signal detected, limited menu items are 
accessible.
Main menu Sub-menu Options
1. 
DISPLAY
Screen Color Off/Whiteboard/Greenboard/
Blackboard
Aspect Ratio Auto/4:3/16:9
Keystone
Position
Phase
H. Size
Zoom
3D Sync TI 3D DLP Link/Off
3D Sync Invert Disable/Invert
Color 
Management Primary Color R
/G /B /C /M /Y
Hue
Saturation
Gain
2. 
PICTURE
Color Mode PC source: Brightest/Daylight/ViewMatch/
Cinema/User 1/User 2
Video source: Brightest/Gaming/ViewMatch/
Cinema/User 1/User 2
Reference Mode PC source: Brightest/Day
light/ViewMatch/Cinema
Video source: Brightest/Gaming/ViewMatch/
Cinema
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color On/Off
Color Temperature T1/T2/T3/T4
Save Settings
3. SOURCEQuick Auto Search On/Off 
						

							
Operation 37
4. 
SYSTEM 
SETUP: 
Basic
Language
Projector PositionFront Table/Rear Table/Rear 
Ceiling/Front Ceiling
Auto Power Off Disable/5 min/10 min/20 min/30 
min/40 min/50 min/60 min
Blank Timer Disable/5 min/10 min/15 min/20 
min/25 min/30 min
Panel Key Lock On/Off
Timer Controller Disable/30 min/1 hr/2 hr/3 hr/4 
hr/8 hr/12 hr
Splash Screen Black/Blue/ViewSonic
Message On/Off
5. 
SYSTEM 
SETUP: 
Advanced
Quick Cooling On/Off
High Altitude Mode On/Off
DCR On/Off
Active VGA Out On/Off
Audio Settings Mute On/Off
Volume
Active Audio Out On/Off
Menu Settings Menu Display 
Time
5 sec/10 sec/15 sec/20 sec/25 
sec/30 sec
Menu Position Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Closed Caption Closed Caption 
Enable
On/Off
Caption Version CC1/CC2/CC3/CC4
Lamp Settings Lamp Mode Normal/Economic
Reset Lamp Timer
Equivalent Lamp Hour
Security 
Settings Change Password
Power On Lock On/Off
Reset All Settings On/Off
6. 
INFORMATIONCurrent System Status •
Source
• Color Mode
• Resolution
• Color System
• Equivalent Lamp Hour