ViewSonic Pjd5211 Projector User Manual

							
Connection
18
Connecting a composit e Video source device
Examine your Video source device to determine if it has a set of unused composite Video 
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of the 
Video source device.
2. Connect the other end of the Video cable to the  VIDEO socket on the projector.
3. If you wish to make use of the projector  (mixed mono) speaker in your presentations, 
take a suitable audio cable and connect one end of the cable to the audio output socket 
of the device, and the other end to the  AUDIO IN socket of the projector.
4. If you wish, you can use another suitable audio cable and connect one end of the cable  to the  AUDIO OUT  socket of the projector, and the other end to your external 
speakers 
Once connected, the audio can be controll ed by the projector On-Screen Display 
(OSD) menus.
The final connection path should be like  that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See  Connecting audio on page 15  for details.
• If the selected video image is not displayed after the projector is turned on and the correct  video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the  signal cables have been connected correctly.
• You need only connect to this device using a composite Video connection if Component  Video and S-Video inputs are unavailable for use. See  Connecting Video source devices 
on page 15  for details.
AV device Video cable 
Audio cable Speakers
Audio 
cable 
						

							
Operation 19
Operation
Starting up the projector
1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch 
(where fitted). Check that the  POWER 
indicator light  on the projector flashes blue 
after power has been applied.
2. Remove the lens cap. If it is closed, it could  become deformed due to the heat produced by 
the projection lamp.
3. Press  POWER on the projector or remote 
control to start the projector. The  POWER 
indicator light  stays blue when the projector is 
on.
The start up procedure takes about 30 seconds. 
In the later stage of start up, a startup logo is 
projected.
(If necessary) Rotate the focus ring to adjust the 
image clearness.
• If the projector is still hot from previous activity, it will run the cooling fan for  approximately 90 seconds before energizing the lamp. 
• To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before  turning it off.
4. If the projector is activ ated for the first time, 
select your OSD language following the on-
screen instructions.
5. Switch all of the connected equipment on.
II 
						

							
Operation
20 6. The projector will start to search for 
input signals. The current input signal being 
scanned appears in the upper left corner of the screen. If the projector doesnt detect a 
valid signal, the message  No Signal will continue to be displayed until an input 
signal is found.
You can also press  SOURCE on the projector or remote control to select your desired 
input signal. See  Switching input signal on page 24  for details.
If the frequency/resolution of the input signal exceeds the projectors operating range, you will 
see the message Out of Range  displayed on a blank screen. Please change to an input signal 
which is compatible with the projectors resolution or set the input signal to a lower setting. 
See  Timing chart on page 52  for details. 
						

							
Operation 21
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various 
adjustments and settings.
Below is the overview of the OSD menu.
To use the OSD menus, please set them to your familiar language first.
1. Press  MENU/EXIT  on the projector or 
MENU  on the remote control to turn the 
OSD menu on. 3. Press  to highlight 
Language  and press  /  to 
select a preferred language .
4. Press  MENU/EXIT  twice* on 
the projector or  Exit on the 
remote control to leave and 
save the settings.
*The first press leads you back 
to the main menu and the 
second press closes the OSD 
menu.
2. Use  /  to highlight the  SYSTEM 
SETUP: Basic  menu.
:  DISPLAY
:  PICTURE
:  SOURCE : 
SYSTEM SETUP: Basic
:  SYSTEM SETUP: Advanced
:  INFORMATION
Current input 
signal
Main menu icon
Sub-menu
Highlight
Go to the 
previous page 
or to exit.
Status
Screen Color
Aspect Ratio
Phase
H. Size
Zoom Off
Auto
16 0
MENU ExitAnalog RGB
ENTERKeystonePosition
3D Sync On Disable
3D Sync Invert
Color Management
Screen Color
Aspect Ratio
Position
Phase
H. Size
Zoom Off
Auto
MENU Exit
Keystone
160
Analog RGB 3D Sync On
3D Sync Invert
Color Management Disable
Projector Position
Auto Power Off
Blank Timer
Timer Controller Panel Key Lock
Splash Screen
Analog RGB
MENU Exit
Front Table DisableDisable
Off
Disable
ViewSonicEnglishLanguage
Projector Position
Auto Power Off
Blank Timer
Timer Controller Panel Key Lock
Splash Screen
Analog RGB
MENU Exit
Front Table DisableDisable
Off
Disable
ViewSonic English
Language 
						

							
Operation
22
Utilizing the password function
For security purposes and to help prevent una uthorized use, the projector includes an option 
for setting up password security. The password  can be set through the On-Screen Display 
(OSD) menu. For details of the OSD menu operation, please refer to  Using the menus on 
page 21 .
You will be inconvenienced if you activate the password functionality and subsequently forget 
the password. Print this user manual (if necessary) and write the password you used in this 
manual, and keep it in a safe place for later use.
Setting a password
Once a password has been set, the projector canno t be used unless the correct password is 
entered every time the projector is started.
1. Open the OSD menu and go to the  SYSTEM SETUP: Advanced > Security 
Settings  menu. Press  MODE/ENTER  on the projector or  Enter on the remote 
control. The  Security Settings  page is displayed.
2. Highlight  Power On Lock  and select On by pressing  / .
3. As pictured to the right, the four arrow keys ( , 
,  ,  ) respectively represent 4 digits (1, 2, 
3, 4). According to the password you desire to 
set, press the arrow keys to enter six digits for the 
password.
4. Confirm the new password by re-entering the  new password.
Once the password is set, the OSD menu returns to the  Security Settings page.
The digits being input will be displayed as asterisks on-screen. Write your selected password 
down here in this user manual in advance or right after the password is entered so that it is 
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
5. To leave the OSD menu, press  MENU/EXIT on the projector or  Exit on the remote 
control .
If you forget  the password
If the password function is activated, you will be asked 
to enter the six-digit password every time you turn on 
the projector. If you enter the wrong password, the 
password error message as pictured to the right is 
displayed lasting for three seconds, and the message 
INPUT PASSWORD  follows. You can retry by 
entering another six-digit password, or if you did not 
record the password in this user manual, and  you absolutely do not remember it, you can use 
the password recall procedure. See  Entering the password recall procedure on page 23  for 
details.
If you enter an incorrect password 5 times in  succession, the projector will automatically 
shut down in a short time.
INPUT NEW PASSWORD
Back
MENU
Password Error
Please try again. 
						

							
Operation 23
Entering the password recall procedure
1. Press and hold AUTO on the projector or remote 
control for 3 seconds. The projector will display 
a coded number on the screen.
2. Write down the number and turn off your  projector.
3. Seek help from the local service center to decode  the number. You may be required to provide 
proof of purchase documentation to verify that 
you are an authorized  user of the projector.
Changing the password
1. Open the OSD menu and go to the  SYSTEM SETUP: Advanced > Security 
Settings  > Change Password  menu.
2. Press  MODE/ENTER  on the projector or  Enter on the remote control. The message 
INPUT CURRENT PASSWORD  is displayed.
3. Enter the old password.
• If the password is correct, another  message INPUT NEW PASSWORD is 
displayed.
• If the password is incorrect, the password  error message is displayed lasting for 
three seconds, and the message  INPUT CURRENT PASSWORD  is 
displayed for your retry. You can press  MENU/EXIT on the projector or  Exit 
on the remote control to cancel the change or try another password.
4. Enter a new password.
The digits being input will be displayed as asterisks on-screen. Write your selected password 
down here in this user manual in advance or right after the password is entered so that it is 
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter  the new password next time the projector is started.
7. To leave the OSD menu, press  MENU/EXIT on the projector or  Exit on the remote 
control  .
Disabling the password function
To disable password protection, go back to the  SYSTEM SETUP: Advanced > Security 
Settings > Power On Lock  menu after opening the OSD menu system. Select  Off by 
pressing / . The message  INPUT PASSWORD  is displayed. Enter the current 
password. 
• If the password is correct, the OSD menu returns to the  Security Settings page 
with  Off shown in the row of  Power On Lock. You will not have to enter the 
password next time you turn on the projector.
• If the password is incorrect, the password  error message is displayed lasting for 
three seconds, and the message  INPUT PASSWORD is displayed for your 
Please write down the recall code, 
and contact ViewSonic 
Customer Center.
Recall code:
0 2 1 2
RECALL PASSWORD
Exit
MENU 
						

							
Operation
24 retry. You can press 
MENU/EXIT on the projector or  Exit on the remote 
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should 
you ever need to re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple de vices at the same time. However, it can only 
display one full screen at a time. 
Be sure the  Quick Auto Search  function in the SOURCE menu is On if you want the 
projector to automatically search for the signals.
You can also manually cycle through the available 
input signals.
1. Press  SOURCE on the projector or remote 
control. A source selection bar is displayed. 
2. Press  /  until your desired signal is  selected and press  MODE/ENTER on the 
projector or  Enter on the remote control.
Once detected, the select ed source information 
will be displayed on the screen for seconds. If 
there are multiple devices connected to the 
projector, repeat steps 1-2 to search for another 
signal.
• The brightness level of the projected image will  change accordingly when you switch between 
different input signals. Data (graphic) PC 
presentations using mostly static images are 
generally brighter than Video using mostly 
moving images (movies).
• The input signal type effects the options available  for the Color Mode. See  Selecting a picture 
mode on page 29  for details.
• The native display resolution of this projector is in a 4:3 aspect ratio. For best display  picture results, you should select and use an input signal which outputs at this resolution. 
Any other resolutions  will be scaled by the projector depending upon the aspect ratio 
setting, which may cause some image distortion or loss of picture clarity. See  Selecting 
the aspect ratio on page 27  for details.
D-Sub / Comp. 1 
Video
S-Video D-Sub / Comp. 2  
						

							
Operation 25
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These 
adjusters change the image height and pr ojection angle. To adjust the projector:
1. Press the quick-release button and lift the  front of the projector. Once the image is 
positioned where you want it, release the 
quick-release button to lock the foot in 
position.
2. Screw the rear adjuster foot to fine tune the  horizontal angle.
To retract the foot, hol d up the projector while 
pressing the quick-release button, then slowly 
lower the projector. Screw  the rear adjuster foot 
in a reverse direction.
If the projector is not placed on a flat surf ace or the screen and the projector are not 
perpendicular to each other, the projected  image becomes trapezoidal. To correct this 
situation, see  Correcting keystone on page 26  for details.
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause 
damage to your eyes.
• Be careful when you press the adjuster button  as it is close to the exhaust vent where hot 
air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the 
picture quality. To do this, press  AUTO on the 
projector or remote control. Within 3 seconds, the 
built-in Intelligent Auto Adjustment function will 
re-adjust the values of Frequency and Clock to 
provide the best picture quality.
The current source information will be displayed 
in the upper left corner of the screen for 3 seconds.
• The screen will be blank while AUTO is 
functioning.
• This function is only available when PC signal  (analog RGB) is selected.
12 
						

							
Operation
26
Fine-tuning the imag e size and clarity
1. Adjust the projected image to the size that you 
need using the zoom ring.
2. Then sharpen the image by rotating the focus ring.
Correcting keystone
Keystoning refers to the situation where the pr ojected image is noticeably wider at either the 
top or bottom. It occurs wh en the projector is not perpendicular to the screen.
To correct this, besides adjust ing the height of the projector, you will need to manually 
correct it following one of these steps.
• Using the remote control
Press  /  on the projector or remote control to 
display the Keystone correction page. Press   to 
correct keystoning at the t op of the image. Press   
to correct keystoning at the bottom of the image.
• Using the OSD menu
1. Press  MENU/EXIT  on the projector or 
MENU  on the remote control and then press 
/  until the 
DISPLAY menu is 
highlighted.
2. Press  to highlight  Keystone and press 
MODE/ENTER  on the projector or  Enter 
on the remote control. The  Keystone 
correction page is displayed.
3. Press   to correct keystoning at the  top of the image or press   to correct 
keystoning at the bottom of the image.
Press/.Press /. 
						

							
Operation 27
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the 
direction arrow keys fo r navigating the picture.
• Using the remote control
1. Press  Magnify +/-  to display the Zoom bar.
2. Press  Magnify + to magnify the center of the 
picture. Press the key repeatedly until the 
picture size is suit able for your need.
3. Use the directional arrows ( ,  ,  ,  ) on  the projector or remote control to navigate the 
picture.
4. To restore the picture to its original size, press  AUTO . You can also press  Magnify -. When 
the key is pressed again,  the picture is further 
reduced until it is restor ed to the original size.
• Using the OSD menu
1. Press  MENU/EXIT  on the projector or  MENU on the remote control and then press 
/  until the  DISPLAY menu is highlighted.
2. Press
  to highlight  Zoom and press  MODE/ENTER  on the projector or  Enter on 
the remote control. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of  Using the remote control above. Or if you are 
using the projector control panel,  continue to the following steps.
4. Press   on the projector repeatedly to  magnify the picture to a desired size.
5. To navigate the picture, press  MODE/ENTER on the projector or  Enter on the 
remote control to switch to the paning m ode and press the directional arrows ( ,  , 
,  ) to navigate the picture.
6. Use the directional arrows ( ,  ,  ,  )  on the projector or remote control to 
navigate the picture.
7. To reduce size of the picture, press  MODE/ENTER on the projector or  Enter on the 
remote control to switch back to the zoom in/out functionality, and press  AUTO to 
restore the picture to its original size. Y ou can also press   repeatedly until it is 
restored to the original size.
The picture can only be navigated after the picture is magnified. You can further magnify the 
picture while searching for details.
Selecting the aspect ratio
The aspect ratio is the ratio of the image  width to the image height. Most analog TV and 
computers are in 4:3 ratio, which is the defaul t for this projector, and digital TV and DVDs 
are usually in 16:9 ratio.
With the advent of digital signal processing,  digital display devices like this projector can 
dynamically stretch and scale the image output to  a different aspect than that of the image 
input signal. 
To change the projected image ratio (n o matter what aspect the source is):
1. Press  MENU/EXIT  on the projector or  MENU on the remote control and then press 
/  until the  DISPLAY menu is highlighted.