ViewSonic Pjd5133 Projector User Manual

Rear View 
Connection ports
AC power socket
Kensington lock
Bottom View
Security bar 
Ceiling mount holes
Ventilation holes
132
1
2
23
1
2
3
3
1
22
3
„This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package.
„Contact your dealer for information to mount the projector on a ceiling.
8 

Using the Product
Control Panel
Power
Turn the projector on or off.
SOURCE
Display the source selection bar.
MENU/EXIT
Display or exit the on-screen display menus.
Keystone/Arrow keys ( /Up,  /Down)
Manually correct distorted images resulting from an angled projection.
Four directional buttons
Use four directional buttons to select items or make adjustments to your  
selection.
MODE
Change the color mode setting by sequence.
POWER (Power LED indicator)
Refer to “LED Indicator Messages”.
TEMP/LAMP...

Connection Ports
AUDIO IN
Connect an audio output from video equipment or computer to this jack.
HDMI
Connect HDMI output from video equipment to this jack.
S-VIDEO
Connect S-Video output from video equipment to this jack.
COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
RS-232
When operating the projector via a computer, connect this to the controlling 
computer's RS-232C port.
MINI USB
This connector is for firmware update and mouse function support.
COMPUTER OUT...

Remote Control
Power
Turn the projector on or off.
VGA1
Display COMPUTER IN 1 signal.
Menu/ Left mouse
Display on-screen display menus.
Perform the left button of the 
mouse when mouse mode is 
activated.
Mouse
/Right mouse
Switch between the normal and 
mouse modes.
Perform the right button of the 
mouse when mouse mode is 
activated.
Keystone/Arrow keys ( /Up, 
/Down)
Manually correct distorted images 
resulting from an angled 
projection.
Left
When the On-Screen Display 
(OSD) menu is activated, the...

Video/Page Up
Switch input source to Composite/
S-Video/HDMI by sequence.
Perform page up function when 
mouse mode is activated.
VGA2
Display COMPUTER IN 2 signal.
ESC/Page Down
Goes back to previous OSD menu.
Perform page down function when 
mouse mode is activated.
Enter
Confirmed selections.
Right/ Lock
Activate panel key lock.
Magnify
Magnifies or reduces the projected 
picture size.
Vo l u m e
Adjust the volume level.
Mute
Cut off the sound temporarily.
Aspect
Select the display aspect ratio.Using...

Installing the Batteries
1. Open the battery cover in the 
direction shown.
2. Install batteries as indicated by the 
diagram inside the compartment.
3. Close the battery cover into 
position.
Caution
„ Risk of explosion if battery is replaced by an incorrect type.
„ Dispose of used batteries according to the instructions.
„
Make sure the plus and minus terminals are correctly aligned when loading a battery.
„Keep the batteries out of the reach of children. There is a danger of death by 
accidentally...

Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„Operating the projector from
the front
7m5m15
158m
„The remote control may not operate when there is sunlight or other strong
light such as a fluorescent lamp shining on the remote sensor.
„Operate the remote control from a position where the remote sensor is visible.„Do not drop the remote control or jolt it.„Keep the remote control out of locations with excessively high temperature or
humidity.
„Do not...

Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Important„In the connections shown above, some cables may not be included with the 
projector (see “Package Contents” on page 6). They are commercially 
available from electronics stores.
„The connection illustrations above are for reference only. The rear 
connecting jacks available on...

Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both!
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are!
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of 
the computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER 
IN 2 signal...

Connecting Video source devices
You can connect your projector to various Video source devices that provide any one 
of the following output sockets:
„HDMI
„Component Video
„S-Video
„Video (composite)
You need only connect the projector to a Video source device using just one of the 
above!connecting methods, however each provides a different level of video quality. 
The method!you choose will most likely depend upon the availability of matching 
terminals on both the!projector and the Video source...