ViewSonic Pjd5111 Projector User Manual

							Operation 37
Function
(default setting/value)Description (default setting/value)
Tint
(0)Adjusts the red and green color tones of the image. See 
Adjusting Tint on page 30 for details.The function is only available when Video or S-Video with 
NTSC system is selected.
Sharpness
(15)Adjusts the image to make it look sharper or softer. See 
Adjusting Sharpness on page 30 for details.
Brilliant 
Color
(On)Adjusts white peaking while maintaining correct color 
presentation. See Adjusting Brilliant Color on page 30 for 
details.
Color 
Temperature
(T1)See Selecting a Color Temperature on page 30 for details.
Save 
SettingsSaves the settings made for the User 1 or User 2 mode.
Quick Auto 
Search
(On)See Switching input signal on page 23 for details.
Language
(English)Sets the language for the On-Screen Display (OSD) menus. See 
Using the menus on page 20 for details.
Projector 
Position
(Front Table)The projector can be installed on a ceiling or behind a screen, or 
with one or more mirrors. See Choosing a location on page 11 
for details.
Auto Power 
Off
(Disable)Allows the projector to turn off automatically if no input signal 
is detected after a set period of time. See Setting Auto Power 
Off on page 41 for details.
Blank Timer
(Disable)Sets the image blank time when the Blank feature is activated, 
once elapsed the image will return to the screen. See Hiding the 
image on page 31 for details.
Panel Key 
Lock
(Off)Disables or enables all panel key functions except POWER 
on the projector and keys on the remote control. See Locking 
control keys on page 31 for details.
2. PICTURE menu
3. SOURCE 
menu4. SYSTEM SETUP: Basic 
menu
II 
						

							Operation 38
Function
(default setting/value)Description (default setting/value)
Timer 
Controller
(Disable)Sets the auto-shutdown timer. The timer can be set to a value 
between 30 minutes and 12 hours.
Splash 
Screen
(ViewSonic logo)Allows you to select which logo screen will display during 
projector start-up. Three options are available: ViewSonic logo, 
Black screen, or Blue screen.
Quick 
Cooling
(On)Selecting On enables the function and the projector cooling time 
will be shortened to a few seconds.If you attempt to restart the projector right after the quick 
cooling process, it may not be turned on successfully and 
will rerun its cooling fans.
High Altitude 
Mode
(Off)A mode for operation in high altitude areas. See Operating in a 
high altitude environment on page 32 for details.
DCR
(Off)Enables or disables the DCR (Dynamic Contrast Ratio) function. 
Selecting On enables the function and the projector will 
automatically switch the lamp mode between normal and 
economic modes according to the input image detected.This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may 
shorten lamp life and noise level will vary during operation.
Active VGA 
Out
(On)Outputs a VGA signal when the COMPUTER IN and 
COMPUTER OUT sockets are correctly connected to devices. 
See Connecting a monitor on page 14 for how to make the 
connection.Enabling this function slightly increases the standby 
power consumption.
Audio 
SettingsMute (Off)
Volume (5)
See Adjusting the sound on page 32 for details.
Menu 
Settings
Menu Display Time (15 sec)
Sets the length of time the OSD will remain active after your last 
key press. The range is from 5 to 30 seconds in 5-second 
increments.
Menu Position (Center)
Sets the On-Screen Display (OSD) menu position.
4. SYSTEM SETUP: 
Basic menu
5. SYSTEM SETUP: Advanced menu 
						

							Operation 39
Function
(default setting/value)Description (default setting/value)
Closed 
Caption
Closed Caption Enable (Off)
Activates the function by selecting On when the selected input 
signal carries closed captions.
• Captions: An on-screen display of the dialogue, narration, 
and sound effects of TV programs and videos that are closed 
captioned (usually marked as CC in TV listings).
Set your screen aspect ratio to 4:3. This function is not 
available when the aspect ratio is “16:9”.
This function is only available when a Composite video or 
S-Video input signal is selected and its system format is 
NTSC.
Caption Version (CC1)
Selects a preferred closed captioning mode. To view captions, 
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the 
primary language in your area).
Lamp 
Settings
Lamp Mode (Normal)
See Setting Lamp mode as Economic on page 41 for details.
Reset Lamp Timer
See Resetting the lamp timer on page 45 for details.
Equivalent Lamp Hour
S
ee Getting to know the lamp hour on page 41 for details 
on how the total lamp hour is calculated.
Security 
SettingsSee Utilizing the password function on page 21 for details,
Reset All 
SettingsReturns all settings to the factory preset values.
The following settings will still remain: Phase, H. Size, User 
1, User 2, Language, Projector Position, High Altitude 
Mode, Security Settings.
Current 
System 
Status
Source
Shows the current signal source.
Preset Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
5. SYSTEM SETUP: Advanced menu
6. INFORMATION menu 
						

							Maintenance 40
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is 
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts 
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens 
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as 
described in Shutting down the projector on page 33 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH 
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the 
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the 
recommended range for the projector. Please refer to Specifications on page 48 or 
consult your dealer about the range.
• Retract the adjuster feet.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. 
						

							Maintenance 41
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically 
calculated by the built-in timer. The method of calculating the equivalent lamp hour is as 
follows:
Total (equivalent) lamp hour
= 1 (hours used in Economic mode) + 4/3 (hours used in Normal mode)
See Setting Lamp mode as Economic below for more information on Economic mode.
The lamp hour in Economic mode is calculated as 3/4 of that in Normal mode. That is, 
using the projector in Economic mode helps to extend the lamp hour by 1/3.
To obtain the lamp hour information:
1. Press MENU/EXIT and then press  /  until the SYSTEM SETUP: Advanced 
menu is highlighted.
2. Press   to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings 
page displays.
3. You will see the Equivalent lamp hour information displaying on the menu.
4. To leave the menu, press MENU/EXIT.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item that normally can last up to 3000-4000 hours with 
proper usage. To keep the lamp life as long as possible, you can do the following settings 
via the OSD menu.
Setting Lamp mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the 
Economic mode is selected, the light output will be reduced and result in darker projected 
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set 
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp 
mode menu and press  / .
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected 
after a set period of time to prevent unnecessary waste of lamp life.
To  s e t  Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and 
press  / . The time period can be set from 5 to 30 minutes in 5-minute increments. If the 
preset time lengths are not suitable for your presentation, select Disable. The projector will 
not automatically shut down in a certain time period. 
						

							Maintenance 42
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to 
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a 
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator 
still lights up after turning the power back on, please contact your dealer. See Indicators on 
page 46 for details.
The following lamp warning displays will remind you to change the lamp.
StatusMessage
The lamp has been in operation for 3500 hours. 
Install a new lamp for optimal performance. If the 
projector is normally run with Economic selected 
(See Setting Lamp mode as Economic on page 
41), you may continue to operate the projector 
until the 3950 hour lamp warning appears.
The lamp has been in operation for 3950 hours. A 
new lamp should be fitted to avoid the 
inconvenience when the projector runs out of lamp 
time.
The lamp has been in operation for 4000 hours.
It is strongly recommended that you replace the 
lamp at this age. The lamp is a consumable item. 
The lamp brightness diminishes with use. This is 
normal lamp behavior. You can replace the lamp 
whenever you notice that the brightness level has 
significantly diminished. If the lamp is not 
replaced beforehand, it must be replaced after 
4000 hours usage.
The lamp MUST be replaced before the projector 
will operate normally.
OK
Order Replacement Lamp
Lamp > 3500 Hours
Notice
OK
Replace Lamp Soon 
Lamp > 3950 Hours
Notice
OK
Replace Lamp Now 
Lamp > 4000 Hours
Lamp usage time exceeded
Notice
OK
Lamp usage time exceeded
Replace lamp (refer to User Manual)
Then reset lamp timer
Notice 
						

							
Maintenance 43
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number : RLC-047
WARNING
Hg - Lamp contains mercury. Manage  in accordance with local disposal 
laws. See www.lamprecycle.org
• To reduce the risk of electrical shock, always turn the projector off and disconnect the 
power cord before changing the lamp.
• To reduce the risk of severe burns, allow the pr ojector to cool for at least 45 minutes 
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution  when removing lamp glass that has shattered into sharp pieces. Before replacing the 
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp 
edges in the lamp compartment. Wash hands after lamp replacement.
• Only ViewSonic certified lamps are tested with this projector. Use of other lamps may  cause electrical shock and fire.
1. Turn the power off and disconnect the 
projector from the wall socket. If the 
lamp is hot, avoid burns by waiting for 
approximately 45  minutes until the 
lamp has cooled.
2. Turn the projector over. Then loosen  the screws on the lamp cover.
3. Remove the lamp cover from the  projector.
WARNING
• Do not turn the power on with the lamp  cover removed.
• Do not insert your fingers between the  lamp and the projector. The sharp edges 
inside the projector may cause injuries.
4. Loosen the screw that secures the lamp. 
						

							Maintenance 445. Pull out the lamp connector from a slot 
in the lamp compartment. Disconnect it 
from the projector as illustrated.
6. Lift the handle so that it stands up. Use 
the handle to slowly pull the lamp out 
of the projector.
CAUTION
• Pulling it too quickly may cause the lamp 
to break and scatter broken glass in the 
projector.
• Do not place the lamp in locations where 
water might splash on it, children can 
reach it, or near flammable materials.
• Do not insert your hands into the projector 
after the lamp is removed. If you touch the 
optical components inside, it could cause 
color unevenness and distortion of the 
projected images.
7. Insert the new lamp into the lamp 
compartment and make sure it fits in 
the projector.
8. Reconnect the lamp connector and 
place it back into its slot to be flush 
with the projector.
1
2
2 
						

							Maintenance 45 13. Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-Screen 
Display (OSD) menu. Go to the SYSTEM 
SETUP: Advanced > Lamp Settings menu. 
Press MODE/ENTER. The Lamp Settings page 
displays. Press   to highlight Reset lamp timer 
and press MODE/ENTER. A warning message 
displays asking if you want to reset the lamp 
timer. Highlight Reset and press MODE/
ENTER. The lamp time will be reset to 0.
CAUTION
Do not reset if the lamp is not new or replaced as this could cause damage. 
9. Tighten the screw that secures the lamp.
CAUTION
• Loose screw may cause a bad connection, 
which could result in malfunction.
• Do not over tighten the screw.
10. Ensure the handle is fully laid flat and 
locked in place.
11. Replace the lamp cover on the 
projector.
12. Tighten the screws that secure the lamp 
cover.
CAUTION
• Loose screw may cause a bad connection, 
which could result in malfunction.
• Do not over tighten the screws.
Reset Lamp Timer?
Reset
Cancel
Notice 
						

							Maintenance 46
Indicators
LightStatus & Description
PowerTe m pLamp
Power events
Blue
FlashingOff OffStand-by mode
Blue Off OffPowering up
Blue Off OffNormal operation
Blue
FlashingOff Off
1. The projector needs 90 seconds to cool down as it was 
abnormally shut down without the normal cooling 
down process. Or
2. The projector needs to cool for 90 seconds after the 
power is turned off. Or
3. The projector has shut down automatically. If you try to 
re-start the projector, it will shut down again. Please 
contact your dealer for assistance.
Lamp events
Purple
FlashingOff RedThe projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact 
your dealer for assistance.
Off Off Red1. The projector needs 90 seconds to cool down. Or
2. Please contact your dealer for assistance.
Thermal events
Off Red Off
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact 
your dealer for assistance.
Off Red Red
Off Red Green
Red Red Red
Red Red Green
Blue Red Red
Blue Red Green
Purple Red Red
Purple Red Green
Off Green Red