ViewSonic Pjd5111 Projector User Manual

							Connection 17
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket 
available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video 
source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
3. If you wish to make use of the projector (mixed mono) speaker in your presentations, 
take a suitable audio cable and connect one end of the cable to the audio output socket 
of the device, and the other end to the AUDIO IN socket of the projector.
4. If you wish, you can use another suitable audio cable and connect one end of the cable 
to the AUDIO OUT socket of the projector, and the other end to your external 
speakers 
Once connected, the audio can be controlled by the projector On-Screen Display 
(OSD) menus. See Adjusting the sound on page 32 for details.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See Connecting audio on page 15 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• If you have already made a Component Video connection between the projector and this 
S-Video source device using Component Video connections, you need not connect to this 
device using an S-Video connection as this makes an unnecessary second connection of 
poorer picture quality. See Connecting Video source devices on page 15 for details.
AV device
S-Video cableAudio cable
Audio 
cable Speakers 
						

							Connection 18
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video 
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of the 
Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
3. If you wish to make use of the projector (mixed mono) speaker in your presentations, 
take a suitable audio cable and connect one end of the cable to the audio output socket 
of the device, and the other end to the AUDIO IN socket of the projector.
4. If you wish, you can use another suitable audio cable and connect one end of the cable 
to the AUDIO OUT socket of the projector, and the other end to your external 
speakers 
Once connected, the audio can be controlled by the projector On-Screen Display 
(OSD) menus. See Adjusting the sound on page 32 for details.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See Connecting audio on page 15 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• You need only connect to this device using a composite Video connection if Component 
Video and S-Video inputs are unavailable for use. See Connecting Video source devices 
on page 15 for details.
AV deviceVideo cable 
Audio cableSpeakers
Audio 
cable 
						

							Operation 19
Operation
Starting up the projector
1. Plug the power cord into the projector and into a 
wall socket. Turn on the wall socket switch 
(where fitted). Check that the POWER 
indicator light on the projector flashes blue 
after power has been applied.
2. Remove the lens cap. If it is closed, it could 
become deformed due to the heat produced by 
the projection lamp.
3. Press POWER on the projector or remote 
control to start the projector. The POWER 
indicator light stays blue when the projector is 
on.
The start up procedure takes about 30 seconds. 
In the later stage of start up, a startup logo is 
projected.
(If necessary) Rotate the focus ring to adjust the 
image clearness.
• If the projector is still hot from previous activity, it will run the cooling fan for 
approximately 90 seconds before energizing the lamp. 
• To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before 
turning it off.
4. Switch all of the connected equipment on.
5. The projector will start to search for input signals. The current input signal being 
scanned displays in the upper left corner of the screen. If the projector doesnt detect a 
valid signal, the message No Signal will continue displaying until an input signal is 
found.
You can also press SOURCE on the projector or remote control to select your desired 
input signal. See Switching input signal on page 23 for details.
If the frequency/resolution of the input signal exceeds the projectors operating range, you will 
see the message Out of Range displayed on a blank screen. Please change to an input signal 
which is compatible with the projectors resolution or set the input signal to a lower setting. 
See Timing chart on page 49 for details.
II 
						

							Operation 20
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various 
adjustments and settings.
Below is the overview of the OSD menu.
To use the OSD menus, please set them to your familiar language first.
1. Press MENU/EXIT on the projector or 
remote control to turn the OSD menu on.3. Press  to highlight 
Language and press  /  to 
select a preferred language.
4. Press MENU/EXIT twice* on 
the projector or remote control 
to leave and save the settings.
*The first press leads you back 
to the main menu and the 
second press closes the OSD 
menu.
2. Use  /  to highlight the SYSTEM 
SETUP: Basic menu.
: DISPLAY
: PICTURE
: SOURCE: SYSTEM SETUP: Basic
: SYSTEM SETUP: Advanced
: INFORMATION
Current input 
signal
Main menu icon
Sub-menu
Highlight
Press MENU/
EXIT to the 
previous 
page or to 
exit.Status
Screen Color
Aspect Ratio
Phase
H. Size
Digital ZoomOff
Auto
16
0
MENU ExitAnalog RGB
ENTERKeystonePosition
Screen Color
Aspect Ratio
Position
Phase
H. Size
Digital ZoomOff
Auto
MENUExit
Keystone
16
0
Analog RGB
Projector Position
Auto Power Off
Blank Timer
Timer Controller Panel Key Lock
Splash Screen
Analog RGB
MENU Exit
Front Table
Disable
Disable
Off
Disable
ViewSonicEnglishLanguage
Projector Position
Auto Power Off
Blank Timer
Timer Controller Panel Key Lock
Splash Screen
Analog RGB
MENU Exit
Front Table
Disable
Disable
Off
Disable
ViewSonicEnglish Language 
						

							Operation 21
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option 
for setting up password security. The password can be set through the On-Screen Display 
(OSD) menu. For details of the OSD menu operation, please refer to Using the menus on 
page 20.
You will be inconvenienced if you activate the password functionality and subsequently forget 
the password. Print this user manual (if necessary) and write the password you used in this 
manual, and keep it in a safe place for later use.
Setting a password
Once a password has been set, the projector cannot be used unless the correct password is 
entered every time the projector is started.
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security 
Settings menu. Press MODE/ENTER. The Security Settings page displays.
2. Highlight Power On Lock and select On by pressing  / .
3. As pictured to the right, the four arrow keys ( , 
,  ,  ) respectively represent 4 digits (1, 2, 
3, 4). According to the password you desire to 
set, press the arrow keys to enter six digits for the 
password.
4. Confirm the new password by re-entering the 
new password.
Once the password is set, the OSD menu returns to the Security Settings page.
The digits being input will display as asterisks on-screen. Write your selected password down 
here in this user manual in advance or right after the password is entered so that it is available 
to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
5. To leave the OSD menu, press MENU/EXIT.
If you forget the password
If the password function is activated, you will be asked 
to enter the six-digit password every time you turn on 
the projector. If you enter the wrong password, the 
password error message as pictured to the right 
displays lasting for three seconds, and the message 
INPUT PASSWORD follows. You can retry by 
entering another six-digit password, or if you did not 
record the password in this user manual, and you absolutely do not remember it, you can use 
the password recall procedure. See Entering the password recall procedure on page 22 for 
details.
If you enter an incorrect password 5 times in succession, the projector will automatically 
shut down in a short time.
INPUT NEW PASSWORD
Back MENU
Password Error
Please try again. 
						

							Operation 22
Entering the password recall procedure
1. Press and hold AUTO on the projector or remote 
control for 3 seconds. The projector will display 
a coded number on the screen.
2. Write down the number and turn off your 
projector.
3. Seek help from the local service center to decode 
the number. You may be required to provide 
proof of purchase documentation to verify that 
you are an authorized user of the projector.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security 
Settings > Change Password menu.
2. Press MODE/ENTER. The message INPUT CURRENT PASSWORD displays.
3. Enter the old password.
• If the password is correct, another message INPUT NEW PASSWORD 
displays.
• If the password is incorrect, the password error message displays lasting for 
three seconds, and the message INPUT CURRENT PASSWORD displays 
for your retry. You can press MENU/EXIT to cancel the change or try another 
password.
4. Enter a new password.
The digits being input will display as asterisks on-screen. Write your selected password down 
here in this user manual in advance or right after the password is entered so that it is available 
to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter 
the new password next time the projector is started.
7. To leave the OSD menu, press MENU/EXIT.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security 
Settings > Power On Lock menu after opening the OSD menu system. Select Off by 
pressing /. The message INPUT PASSWORD displays. Enter the current password. 
• If the password is correct, the OSD menu returns to the Security Settings page 
with Off shown in the row of Power On Lock. You will not have to enter the 
password next time you turn on the projector.
• If the password is incorrect, the password error message displays lasting for 
three seconds, and the message INPUT PASSWORD displays for your retry. 
You can press MENU/EXIT to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should 
you ever need to re-activate the password function by entering the old password.
Please write down the recall code, 
and contact ViewSonic 
Customer Center.
Recall code:
0 2 1 2
RECALL PASSWORD
Exit
MENU 
						

							Operation 23
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only 
display one full screen at a time. 
Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default 
of this projector) if you want the projector to automatically search for the signals.
You can also manually cycle through the available 
input signals.
1. Press SOURCE on the projector or remote 
control. A source selection bar displays. 
2. Press  /  until your desired signal is 
selected and press MODE/ENTER.
Once detected, the selected source information 
will display on the screen for seconds. If there 
are multiple devices connected to the 
projector, repeat steps 1-2 to search for another 
signal.
• The brightness level of the projected image will 
change accordingly when you switch between 
different input signals. Data (graphic) PC 
presentations using mostly static images are 
generally brighter than Video using mostly 
moving images (movies).
• The input signal type effects the options available 
for the Preset Mode. See Selecting a picture 
mode on page 28 for details.
• The native display resolution of this projector is in a 4:3 aspect ratio. For best display 
picture results, you should select and use an input signal which outputs at this resolution. 
Any other resolutions will be scaled by the projector depending upon the aspect ratio 
setting, which may cause some image distortion or loss of picture clarity. See Selecting 
the aspect ratio on page 26 for details.
D-Sub / Comp. 1 
Video
S-Video D-Sub / Comp. 2  
						

							Operation 24
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These 
adjusters change the image height and projection angle. To adjust the projector:
1. Press the quick-release button and lift the 
front of the projector. Once the image is 
positioned where you want it, release the 
quick-release button to lock the foot in 
position.
2. Screw the rear adjuster foot to fine tune the 
horizontal angle.
To retract the foot, hold up the projector while 
pressing the quick-release button, then slowly 
lower the projector. Screw the rear adjuster foot 
in a reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not 
perpendicular to each other, the projected image becomes trapezoidal. To correct this 
situation, see Correcting keystone on page 25 for details.
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause 
damage to your eyes.
• Be careful when you press the adjuster button as it is close to the exhaust vent where hot 
air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the 
picture quality. To do this, press AUTO on the 
projector or remote control. Within 3 seconds, the 
built-in Intelligent Auto Adjustment function will 
re-adjust the values of Frequency and Clock to 
provide the best picture quality.
The current source information will be displayed 
in the upper left corner of the screen for 3 seconds.
• The screen will be blank while AUTO is 
functioning.
• This function is only available when PC signal 
(analog RGB) is selected.
12 
						

							Operation 25
Fine-tuning the image size and clarity
1. Adjust the projected image to the size that you 
need using the zoom ring.
2. Then sharpen the image by rotating the focus ring.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the 
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually 
correct it following one of these steps.
• Using the remote control
Press  /  on the projector or remote control to 
display the Keystone correction page. Press   to 
correct keystoning at the top of the image. Press   
to correct keystoning at the bottom of the image.
• Using the OSD menu
1. Press MENU/EXIT and then press  /  
until the 
DISPLAY menu is highlighted.
2. Press  to highlight Keystone and press 
MODE/ENTER. The Keystone correction 
page displays.
3. Press   to correct keystoning at the top of 
the image or press   to correct keystoning at 
the bottom of the image.
Press/.Press /. 
						

							Operation 26
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the 
direction arrow keys for navigating the picture.
• Using the remote control
1. Press Digital Zoom +/- to display the Zoom 
bar.
2. Press Digital Zoom + to magnify the center of 
the picture. Press the key repeatedly until the 
picture size is suitable for your need.
3. Use the directional arrows ( ,  ,  ,  ) on 
the projector or remote control to navigate the 
picture.
4. To restore the picture to its original size, press 
AUTO. You can also press Digital Zoom -. 
When the key is pressed again, the picture is further reduced until it is restored to the 
original size.
• Using the OSD menu
1. Press MENU/EXIT and then press  /  until the DISPLAY menu is highlighted.
2. Press
  to highlight Digital Zoom and press MODE/ENTER. The Zoom bar 
displays.
3. Repeat steps 2-4 in the section of Using the remote control above. Or if you are 
using the projector control panel, continue to the following steps.
4. Press   on the projector repeatedly to magnify the picture to a desired size.
5. To navigate the picture, press MODE/ENTER to switch to the paning mode and 
press the directional arrows ( , ,  ,  ) to navigate the picture.
6. Use the directional arrows ( ,  ,  ,  ) on the projector or remote control to 
navigate the picture.
7. To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out 
functionality, and press AUTO to restore the picture to its original size. You can also 
press   repeatedly until it is restored to the original size.
The picture can only be navigated after the picture is magnified. You can further magnify the 
picture while searching for details.
Selecting the aspect ratio
The aspect ratio is the ratio of the image width to the image height. Most analog TV and 
computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs 
are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can 
dynamically stretch and scale the image output to a different aspect than that of the image 
input signal. 
To change the projected image ratio (no matter what aspect the source is):
1. Press MENU/EXIT and then press  /  until the DISPLAY menu is highlighted.
2. Press
  to highlight Aspect Ratio.
3. Press  /  to select an aspect ratio to suit the format of the video signal and your 
display requirements.