ViewSonic Pj510 Projector User Manual

ViewSonic  PJ51028
SCREEN Menu
With the SCREEN menu, the items shown in the Table below can be 
performed. Perform each operation in accordance with the instructions in the 
table below.
Item Description
BLANK Select a Blank Screen Color: 
BLUE (S) Q (T) WHITE (S) Q (T
) BLACK
• The blank screen of selected color is displayed by pressing the BLANK button. Please refer to the 
section “Temporarily Blanking The Screen” of “Operation” about the screen blanking.
START UP Select the Start Up Screen:
TURN ON...

29ViewSonic  PJ510
OPTION Menu
With the OPTION menu, the items shown in the Table below can be performed. 
Perform each operation in accordance with the instructions in the table below.
Item Description
VOLUME
Adjust the Volume: High (S) Q (T) Low
SCREEN TYPE Select the Screen Type:
4:3(S)Q(T)16:9-TOP(S)Q(T)16:9-CENTER(S)Q(T)16-9:BOTTOM 
• Please select the screen type used and the picture position in case of 16:9. This selection is used 
as basic information for a suitable display. This function should...

ViewSonic  PJ51030
Lamp
     HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
 WA R N I N G
The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a 
loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each 
lamp has a different lifetime, and some may burst or burn out soon after you start using them. In 
addition, when the bulb bursts, it is possible for shards of glass
 to fly into the lamp housing, and for 
gas containing...

31ViewSonic  PJ510
Replacing The Lamp 
If the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. 
Using the lamp for long periods of time, or past the replacement date, could cause it to burst. If the 
projector is mounted on the ceiling, or if the lamp has broken, do not try to clean the projector or 
replace the lamp yourself.
1Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 
minutes.
2Contact your local dealer...

ViewSonic  PJ51032
Air Filter
Caring For The Air Filter
The air filter should be cleaned about every 100 hours. If the indicators or a message prompts you to 
clean the air filter, clean the air filter as soon as possible. If the air filter becomes clogged by dust or 
the like, internal temperature rises and could cause malfunction.
1Turn off the projector, and unplug the power cord.
2Apply a vacuum cleaner to the top of the filter cover to clean 
the air filter.
3Reset the filter timer, according to...

33ViewSonic  PJ510
Replacing The Air Filter
If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. 
Please replace the air filter as soon as possible.
1Turn off the projector, and unplug the power cord.
2Contact your local dealer to prepare a new air filter. Tell the 
dealer your air filter type number.
3After making sure that the projector has cooled adequately, 
remove the filter cover. Hold the release buttons of the filter 
cover, while pulling it up....

ViewSonic  PJ51034
Other Care
Caring For The Inside Of The Projector
In order to ensure the safe use of your projector, please have it cleaned and inspected by your local 
dealer about once every 2 years. Never try to care for the inside of the unit yourself. Doing so is 
dangerous.
Caring For The Lens
1Turn off the projector, and unplug the power cord.
2Lightly wipe the lens with a commercially available lens-
cleaning wipe.
Do not touch the lens directly with your hand.
Caring For The Cabinet And...

35ViewSonic  PJ510
Troubleshooting
Related Messages
When the units power is ON, messages such as those shown below may be displayed. When any 
such message is displayed on the screen, please respond as described below. If the same message is 
displayed after the treatment, or if a message other than the following appears, please contact your 
dealer or service company.
Note:
* Although this message will be automatically disappeared after around 3 minutes, it will be 
reappeared every time the power is...

ViewSonic  PJ51036
1Turn off the projector, and unplug the power cord.
2After making sure that the projector has cooled adequately, remove the 
filter cover.
 
Hold the release buttons of the filter cover, while pulling it up. 
3Wipe the transparent area of the filter cover by using a swab or a soft cloth. 
4Remove the air filter.
Hold the release buttons of the air filter, while pulling it down. 
5Wipe the dust-detecting window by using a soft cloth.
6Replace the air filter and filter cover.
 AT T E N T...

37ViewSonic  PJ510
Regarding The Indicator Lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have 
the meanings as described in the Table below. Please respond in accordance with the instructions 
within the Table. If the same indication is displayed after the treatment, or if an indication other than 
the following is displayed, please contact your dealer or service company.
 AT T E N T I O N
When the interior portion has become overheated, for safety...