Vidikron Projector Vision Model 85 User Manual
Here you can view all the pages of manual Vidikron Projector Vision Model 85 User Manual. The Vidikron manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 71
Operation Vidikron Vision 85 Owner’s Operating Manual 59 PREL IMINARY Fan Mode: If the projector is being used in a high-altitude environment, use the Fan Mode control to prevent it from overheating. Set it to High Altitude (2) to run the fan at high speed; set it to Normal (1) to run the fan at normal speed. Orientation: Refer to Adjusting the Picture Orientation on page 32. Factory Default: To reset all projector settings (including image settings) back to their factory defaults, choose Factory...
Page 72
Operation 60 Vidikron Vision 85 Owner’s Operating Manual PREL IMINARY Notes:
Page 73
Vidikron Vision 85 Owner’s Operating Manual 61 PREL IMINARY 5.1 Lamp Replacement The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. Contact your Vidikron dealer to obtain a replacement lamp. 1. Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. 2. Using a Phillips screwdriver, loosen the two...
Page 74
Maintenance and Troubleshooting 62 Vidikron Vision 85 Owner’s Operating Manual PREL IMINARY 5.2 Troubleshooting Tips Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the Vision 85. If you encounter an issue not described here or in Section 3 (refer to Installation Considerations on page 18), or if the suggested solutions fail to resolve the problem, please contact your Vidikron dealer or Vidikron Technical Support. Table 5-1. Troubleshooting Chart...
Page 75
Maintenance and Troubleshooting Vidikron Vision 85 Owner’s Operating Manual 63 PREL IMINARY Image geometry is incorrect. Incorrect aspect ratio selection. Image height may need adjusting (Vision 85/CineWide only). Select the aspect ratio that best matches the source image and screen size (refer to Table 4-1). Adjust displayed image height (refer to Display Device on page 49). The projected image is trapezoidal in shape. The projector is not perpendicular to the screen. Adjust...
Page 76
Maintenance and Troubleshooting 64 Vidikron Vision 85 Owner’s Operating Manual PREL IMINARY Notes:
Page 77
Vidikron Vision 85 Owner’s Operating Manual 65 PREL IMINARY 6.1 RS-232 Connection and Port Configuration To interface the VHD Controller with a home theater automation/control system or a PC running terminal emulation software, connect it to your control system or PC as shown in Figure 3-11. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 19200, to match that of the VHD Controller RS-232 port. 6.2 Serial...
Page 78
Serial Communications 66 Vidikron Vision 85 Owner’s Operating Manual PREL IMINARY Input Selection Commands COMPONENTNAYESSelects the Component input COMPOSITENAYESSelects the Composite video input HDMI1NAYESSelects the HDMI 1 input HDMI2NAYESSelects the HDMI 2 input HD1NA YESSelects the HD 1 input HD2NA YESSelects the HD 2 input INPUT?NANAReturns active input SVIDEO1NAYESSelects the S-Video 1 input SVIDEO2NAYESSelects the S-Video 2 input Aspect Ratio Commands ANAMORPHICNAYESSelects the Anamorphic...
Page 79
Serial Communications Vidikron Vision 85 Owner’s Operating Manual 67 PREL IMINARY Picture Adjust Commands (not available on HDMI 1 or HDMI 2 inputs) BRIGHTNESS-100/100YESSets a value for brightness BRIGHTNESS?NANAReturns brightness setting value CHROMADELAY-12/12YESSets a value for input color chroma delay CHROMADELAY?NANAReturns input color chroma delay setting COLOR-100/100YESSets a value for color COLOR?NANAReturns color setting value CONTRAST-100/100YESSets a value for contrast CONTRAST?NANAReturns...
Page 80
Serial Communications 68Vidikron Vision 85 Owner’s Operating Manual PREL IMINARY Input Position Commands (not available on HDMI 1 or HDMI 2 inputs) IHEIGHT-100/100YESSets the value for input height IHEIGHT?NANAReturns input height value IHPOS-100/100YESSets a value for horizontal input position IHPOS?NANAReturns input horizontal position value IVPOS-100/100YESSets a value for vertical input position IVPOS?NANAReturns input vertical position value IWIDTH-100/100YESSets the value for input width...