Vidikron Projector Vision Model 85 User Manual

Operation
Vidikron Vision 85 Owner’s Operating Manual 49 
PREL
IMINARY
Display Device: The options in the Display Device menu allow you to change the picture 
orientation, adjust the amount of overscan and access other projector-specific functions.
•Configure: Select Configure from the Display Device menu. Then: 
Orientation: Select Orientation to change the picture orientation to suit the method of 
installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear). 
Overscan: Refer to Overscan on...

Operation
50 Vidikron Vision 85 Owner’s Operating Manual
PREL
IMINARY
Miscellaneous: Select Miscellaneous from the Service menu to set the following options: 
• Language: Select Language from the Miscellaneous menu and press the up- or 
down-arrows to select the OSD Language. (Currently, only English is supported.) 
•Menu Mode: This is the manner in which the OSD menus appear and disappear when you 
press MENU. Choose one of the following: 
0 = No transition; menus abruptly appear and disappear.  
1 =...

Operation
Vidikron Vision 85 Owner’s Operating Manual 51 
PREL
IMINARY
4.3 
On-Screen Menus for 1080i 
(Digital) or 1080p Signals
After you have finished calibrating the projector to optimize the display of 1080i analog and 
lower-resolution sources, do likewise for 1080i digital and 1080p sources (connected to the 
HDMI 1 or HDMI 2 inputs on the VHD Controller). 
When the projector receives a 1080i digital and 1080p signal, it displays the menus shown in 
Figure 4-6. 
Figure 4-6. OSD Menu Structure for...

Operation
52 Vidikron Vision 85 Owner’s Operating Manual
PREL
IMINARY
Main MenuPress MENU on either the remote control or built-in keypad (on the projector rear panel) to 
display the Main Menu, shown in 
Figure 4-7. The Main Menu is the starting point for 
calibrating the Vision 85 to optimize the display of digital 1080i and 1080p sources. 
Figure 4-7. Vision 85 Main Menu (1080i Digital or 1080p Sources Only)
To use the on-screen menus:
1. Press  or  to select a sub-menu.
2. Press  or  to select a...

Operation
Vidikron Vision 85 Owner’s Operating Manual 53 
PREL
IMINARY
LanguageThe Vision 85 OSD language is initially set to English, but can also display the menus in 
German (Deutsch), Spanish (Español), French (Français) or Italian (Italiano). To change the 
OSD language:
1. Press MENU.
2. Press  or  to select Language from the Main Menu.
3. Press up- or down-arrow button ( or ) to highlight the desired language and press 
ENTER. The change takes effect immediately. 
Picture AdjustTo perform basic...

Operation
54 Vidikron Vision 85 Owner’s Operating Manual
PREL
IMINARY
Contrast: Refer to Contrast on page 41.
Brightness: Refer to Brightness on page 40.
Color: Refer to Color Saturation on page 41.
Tint: Refer to Tint on page 42.
Sharpness: Refer to Sharpness on page 43.
Color Temp.: To adjust the color temperature, select Color Temp. from the Picture Adjust 
menu. (Color temperature defines the “color of gray.”) Press  or  to select 5500, 6500, 
7500, 8500, 9300 or 10500. In most cases, 6500 or 7500...

Operation
Vidikron Vision 85 Owner’s Operating Manual 55 
PREL
IMINARY
Picture Adjust (Advanced)To access advanced picture quality settings, select Advanced from the Picture Adjust menu. 
This sub-menu presents the following options:
ICC Adjust: Select ICC Adjust from the Advanced Picture Adjust menu to customize the 
displayed color space. The adjustments you make here are stored in the currently-selected 
“
Picture Memory“ preset. 
For each of the six primary colors – red, yellow, green, cyan, blue and...

Operation
56 Vidikron Vision 85 Owner’s Operating Manual
PREL
IMINARY
Video NR: To apply noise reduction to the input signal, select Video NR from the Advanced 
Picture Adjust menu. Noise reduction is useful for improving the signal-to-noise ratio of 
video signals. Set it to Off, 1, 2 or 3, as needed, keeping in mind that higher settings (which 
reduce high frequencies) may also “soften” the image.
MNR: Select MNR from the Picture Adjust menu to reduce or eliminate so-called “mosquito 
noise” in...

Operation
Vidikron Vision 85 Owner’s Operating Manual 57 
PREL
IMINARY
HD/RGB Adj. Select HD/RGB Adj. from the Main Menu to view input signal resolution and timing 
information. To do this, select Signal Info from the HD/RGB Adj. menu. 
Signal Info: Select Signal Info from the HD/RGB Adj. menu to display the resolution, 
horizontal frequency and vertical frequency of the input current signal. 
OptionsSelect Options from the Main Menu to perform the following projector configuration tasks.
Image Shift:...

Operation
58Vidikron Vision 85 Owner’s Operating Manual
PREL
IMINARY
Signal Type: Select Signal Type from the Options menu to specify the incoming signal type 
(encoding method): 
 Choose Auto to have the Vision 85 automatically detect the signal type. 
 Choose RGB (1) for RGB-encoded video signals. 
 Choose YCrCb4:4:4 (2) for uncompressed, component video. This encoding method uses a 
“luminance” signal (Y) to represent brightness and “difference” signals (Cb and Cr) to 
represent colors. 
 Choose...