Vidikron Projector Vision Model 80 User Manual

31
What to do when these messages are displayed
 Message  Cause (Details)
No device is connected to the DVI terminal.
The terminal is connected but there is no signal output.
➝ Input the video signals.
When lamp time reaches 1000 hours
➝  A message indicating “1000 h” will be displayed on the screen.
  • Press the [EXIT ] button to clear the display.
At the moment when the accumulated lamp time reaches 1900 
hours, a “Lamp replacement” message will be displayed. In addition, 
when the accumulated lamp...

32
Warning Indication
About warning indicators
If an abnormality occurs in this unit during projection, the warning mode will be triggered and the type of abnormality will be indicated 
by a combination of indicators displayed on the control panel. This unit will then automatically stop projection and run the cooling fan for 
about 90 seconds.
No. Indicator
Warning
[LAMP] [TEMP] [STAND BY] [OPERATE]
1 Blinking Blinking Lamp does not light up and unit is unable to project
2 Blinking Blinking...

33
Troubleshooting
Before sending the unit to your Vidikron dealer for repair, check the following points.
Symptom Probable Cause Corrective Action Reference Page
Power is not supplied. • Is the power cord disconnected? • Insert the power cord (plug) fi  rmly. 4 – 6,  20
• Is the lamp cover properly shut? •  Contact your Vidikron dealer for 
service.29
• Is the fi lter cover properly shut? •  Contact your Vidikron dealer for 
service.30
•  Has the lamp life expired? (Has the 
lamp usage time reached 2000...

34
Terminal Description
Pin Arrangement
Pin No. Signal Name Pin No. Signal Name
1 N/C 6 N/C
2 RD 7 N/C
3 TD 8 N/C
4 N/C 9 N/C
5 GND
Pin No. Signal Name Pin No. Signal Name
1 TMDS data 2- 13 N/C
2 TMDS data 2+ 14 TMDS +5 V power supply
3 TMDS data 2/4 shield 15 Earth (+5 V )
4 N/C 16 Hot plug detection
5 N/C 17 TMDS data 0-
6 DDC clock 18 TMDS data 0+
7 DDC data 19 TMDS data 0/5 shield
8 N/C 20 N/C
9 TMDS data 1- 21 N/C
10 TMDS data 1+ 22 TMDS clock shield
11 TMDS data 1/3 shield 23 TMDS clock +
12 N/C 24...

35
RS-232C External Control
Control of this unit via an automation control system is possible by connecting it to this unit with a RS-232C cross cable (D-sub 9 pins). The 
commands to control this unit and the response data format against the received commands are explained here. For details, please consult 
your authorized dealer.
1. Communication Specifi cations
 Communication specifi cation for this unit are as follows:
Baud Rate 9600/19200 bps
Data Length 8 bit
Parity None
Stop Bit 1 bit
Flow Control...

36
  2-3. Parameters used for the data format
  The following 3 types of parameters are used for command and response data:
      1 Numeric value 2 ON/OFF 3 Special parameters
    Each parameter is as follows:
  1 Numeric value
      A 2-byte hexadecimal value (sign included) is represented by a set of 4-digit (4-byte) characters.
      Assignable range: 8000H to 7FFFH
  2 ON/OFF
      Shows the status (ON or OFF) of the unit, such as POWER and HIDE.
Character Hex Meaning
0 30 OFF
131ON
  3 Special...

37
Specifi cations
Projection Type:D-ILA, 3-chip, 0.82 in. diagonal
Native Resolution:1920 x 1080 (16:9)
Aspect Ratio:  4:3, Letterbox,16:9 Anamorphic
DTV Compatibility:480p, 720p, 1080i, 1080p
Picture Size (16:9 screen):Recommended Width: 72 – 96 in.
Maximum Width: 240 in. 
Light Output: CSMS*  Specifi cations: Home Theater Calibration: 491 ANSI Lumens; 18.1 Foot-Lamberts (fL); 
1050 ANSI Lumens
Contrast Ratio:2100:1 ANSI
Lamp:250 W UHP
Estimated Lamp Life:2000 Hours @ 6500 Kelvin
Inputs:(1) DVI w/HDCP,...

38
Dimensions
17.998
20.125
5.932
4.499 3.209 

39 

Vidikron
2900 Faber Street
Union City, CA 94587
510-324-5900
Fax 510-324-5905
1-888-4-VIDIKRON
RUMA-011080
Version 1.0