Vidikron Projector Vision Model 65 User Manual

							Maintenance and Troubleshooting
Vidikron Vision Model 65/Model 75 Installation/Operation Manual 65 
LAMP LED lights solid red. The lamp has failed or 
exceeded its usage life. Replace the lamp with a 
new one. 
TEMP LED lights solid red. Vision 65/75 internal 
temperature is too high or 
one or more fans have 
failed. Power off the Vision 65/75 
and allow it to cool down. 
Ensure that the intake and 
exhaust vents are not 
blocked. Turn the projector 
back on. If the problem 
persists, please contact 
your Vidikron dealer for 
assistance. 
Table 5-1. Troubleshooting Chart (continued)
Symptom Possible Cause(s) Solution 
						

							Maintenance and Troubleshooting
66 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
Notes: 
						

							Vidikron Vision Model 65/Model 75 Installation/Operation Manual 67 
6.1 
RS-232 Connection and 
Port Configuration
To interface the Vision 65/75 with a home theater automation/control system or a PC 
running terminal emulation software:
1. Connect it to your control system or PC as shown in Figure 3-14. 
2. Start a terminal session on your PC using a terminal-emulation program, such as 
HyperTerminal. 
3. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop 
bit and no flow control. Set the baud rate to 19200. 
4. Type a command from among those listed in Table 6-1. For example, to select the 
Component 1 input, type X133X. Do not send a carriage return after the command.
6.2 
Serial Command Syntax
Serial commands to the Vision 65/75 take the following form:
 Commands are in ASCII format.
 Commands must be in UPPERCASE; for example, X001X, not x001x.
 When you send a valid command, the Vision 65/75 executes it and echoes the command 
back to the PC or control system. For example, when you send the command X001X, the 
Vision 65/75 responds with X0_001X. 
 When you enter an invalid command, the Vision 65/75 simply ignores it.
6Serial Communications
The Vision 65/75 will not accept serial commands for 20 seconds after it is 
turned on or off. 
Table 6-1. Serial Commands 
CodeFunction
X001XPower On 
X002XPower Off
X003XMenu
X004XEnter
X005XExit
X006XUp (arrow key)
X007XDown (arrow key)
X008XLeft (arrow key)
X009XRight (arrow key)
X011XShow active source and aspect ratio information
X021XKeypad 1
Note 
						

							Serial Communications
68 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
X022XKeypad 2
X023XKeypad 3
X024XKeypad 4
X025XKeypad 5
X026XKeypad 6
X027XKeypad 7
X028XKeypad 8
X029XKeypad 9
X030XKeypad 0
X041XRestore image settings from Custom 1
X042XRestore image settings from Custom 2
X043XRestore image settings from ISF Day
X044XRestore image settings from ISF Night
X047XRestore all Picture Adjust Menu options to their factory-default values
X048XRestore all Setup Menu options to their factory-default values
X051XSet Gamma to 2.2
X056XIncrease PIP sub-window size
X057XDecrease PIP sub-window size
X058XSet PIP active window
X059XSet PIP on 
X060XSet PIP off
X061X16:9 aspect ratio
X062X4:3 aspect ratio
X063XLetterbox aspect ratio
X064XIntelliWide aspect ratio
X065XCinema aspect ratio
X066XIntelliWide 2.35 aspect ratio
X082XImage orientation = floor front
X083XImage orientation = ceiling front
X084XImage orientation = floor rear
Table 6-1. Serial Commands (continued)
Code Function 
						

							Serial Communications
Vidikron Vision Model 65/Model 75 Installation/Operation Manual 69 
X085XImage orientation = ceiling rear
X091XLamp Power = 170W
X092XLamp Power = 200W
X100XBlack Threshold = 0 IRE
X101XBlack Threshold = 7.5 IRE
X112XColor Temperature = 5400K
X113XColor Temperature = 6500K
X114XColor Temperature = 9300K
X115XColor Temperature = Custom 1
X116XColor Temperature = Custom 2
X121XOSD Language = English
X122XOSD Language = French
X123XOSD Language = Spanish
X124XOSD Language = German
X125XOSD Language = Italian
X131XSwitch to Composite input
X132XSwitch to S-Video input
X133XSwitch to Component 1 input
X134XSwitch to Component 2 input
X135XSwitch to HDMI 1 input 
X136XSwitch to HDMI 2 input 
X137XSwitch to RGBHV input 
X151XReset Lamp Timer
X156XBackground Color = Black
X157XBackground Color = Blue
X158XBackground Color = Gray
X180XBlue Image ON
X181XBlue Image OFF
Table 6-1. Serial Commands (continued)
Code Function 
						

							Serial Communications
70 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
Notes: 
						

							Vidikron Vision Model 65/Model 75 Installation/Operation Manual 71 
7.1 
Vision 65/75 Specifications
Table 7-1 lists the Vision 65/75 specifications.  
7Specifications
Table 7-1. Vision 65/75 Specifications 
Projector Type:Digital Light Processing (DLP), Single-Chip DMD
Native Resolution:1920 x 1080 (16:9)
Aspect Ratios:4:3, Letterbox, 16:9, IntelliWide, Cinema, IntelliWide 2.35
Video Standards:NTSC, PAL, ATSC
Video Compatibility:480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Scan Frequency:Horizontal: 15 - 80 kHz 
Vertical: 50 - 100 Hz
Picture Size (16:9 Screen):Recommended Width: 72 in. (1.83 m) to 96 in. (2.44 m)
Throw Distance 
(Factor x Screen Width):Refer to Table 3-3
Vertical Offset (when 
projector is inverted):Up = 35% of screen height above lens center (70% of one half of 
the screen height)
Down = 50% of screen height below lens center (100% of one 
half of the screen height) 
						

							Specifications
72 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
Brightness and Contrast: Cinema Standards Measurement System (CSMS) 
Specifications – Vision Model 65 Series
- Brightness*: 13.6 to 19.6 foot-Lamberts (fL)
- Contrast Ratio*: 200:1 to 220:1
Cinema Standards Measurement System (CSMS) 
Specifications – Vision Model 75 Series
- Brightness*: 14.8 to 21.7 foot-Lamberts (fL)
- Contrast Ratio*: 200:1 to 230:1
*Variable depending on VAC setting
These measurements are taken from the projector in a 
controlled, home theater environment. All measurements are 
made to ANSI/NAPM IT7.228-1997 specifications using the 
Photo Research PR-650 SpectraColorimeter and Minolta LS-100 
Luminance Meter, Video Essentials test DVD and a 1.3 gain, 
72-inch wide screen. The projector is calibrated to a color 
temperature of 6,500K and has a minimum of 150 hours of 
usage.
The foot-Lambert (fL) is the unit of measurement used in 
commercial movie theaters to express image brightness at the 
screen surface. The Society of Motion Picture and Television 
Engineers (SMPTE) specifies 16 fL as the target image brightness 
for film-based projectors using an open gate (without film in the 
projector). More importantly, today SMPTE specifies 12 fL as the 
target image brightness in Digital Cinema theaters. The 
foot-Lambert measurement is dependent on screen size, screen 
gain and projector light output.
Home Theater Calibration Specifications – Vision 
Model 65 Series
- Light Output: 436 to 541 ANSI Lumens
- Contrast Ratio*: 200:1 to 220:1
Home Theater Calibration Specifications – Vision 
Model 75 Series
- Light Output: 451 to 589 ANSI Lumens
- Contrast Ratio*: 200:1 to 230:1
These specifications are obtained by calibrating the projector as 
described above for CSMS measurements. 
Industry-Standard Specifications – Vision Model 65 Series
- Light Output: 1150 ANSI Lumens
- Contrast Ratio: 3000:1
Industry-Standard Specifications – Vision Model 75 Series
- Light Output: 1290 ANSI Lumens
- Contrast Ratio: 11,000:1
These are typical projector brightness and contrast 
specifications found in most companies’ sales literature. 
Vidikron includes these measurements in its literature to allow 
for direct comparison with other manufacturers’ projectors. 
These measurements are typically taken at 9,000K to 13,000K to 
get expected performance data when the projector is used in 
professional, commercial and industrial displays.
Lamp:200 Watts
Estimated Lamp Life: 2000 hours
Video Inputs: (1) Composite Video, (1) S-Video, (1) RGB/Component Video 
(5
 x BNC), (1) RCA Component Video (3 x RCA), (2) HDMI
Table 7-1. Vision 65/75 Specifications (continued) 
						

							Specifications
Vidikron Vision Model 65/Model 75 Installation/Operation Manual 73 
Control Options:- Discrete IR remote
- Serial commands via RS-232
RS-232 Communication 
Parameters: 19200 bps, no parity, 8 data bits, 1 stop bit, no flow control 
+12V Output:Max. 0.25 Amps, active when Cinema or IntelliWide 2.35 Aspect 
Ratio is selected (CineWide versions only) or when projector is 
turned on; Tip = +12V; Sleeve = Ground
Power Requirements:100 to 240 VAC (auto-sensing), 50/60 Hz, 290 Watts 
(989.8
 BTUs/hour)
Operating Environment:41°F to 95°F (5°C to 35°C), 20% to 80% humidity 
(non-condensing) 
Dimensions:See Figure 7-1
Weight (without lens):34 lbs. (15.42 kg)
Regulatory Approvals:Complies with FCC Class B, CE, C-Tick, GOST, TUV-GS, cTUV-US
Limited Warranty: Projector: Two (2) years parts and labor from the date of delivery 
to the end user.
Lamp: 1000 hours or six (6) months, whichever comes first. 
Specifications are subject to change without notice. 
Table 7-1. Vision 65/75 Specifications (continued) 
						

							Specifications
74 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
7.2 
Vision 65/75 Dimensions
Figure 7-1 shows the Vision 65/75 dimensions (all dimensions are in inches). 
Figure 7-1. Vision 65/75 Dimensions (with Optional Fixed Anamorphic Lens)
8.0
1.3
0.8
11.018.9 22.3 22.0
1.9
2.44.9
02X 2.4 6.5 15.3 19.722.0
15.3
6.7 10.8
0 3.4
2.9
18.9 17.1 15.1 1.1
2X 15.1 2X 2.1 1.2 7.9