Home > Vidikron > Projector > Vidikron Projector Vision Model 65 User Manual

Vidikron Projector Vision Model 65 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Vidikron Projector Vision Model 65 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 45 Vidikron manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Vidikron Vision Model 65/Model 75 Installation/Operation Manual 5 
    2.1 
    Vision 65/75 at a Glance
    Figure 2-1 and Figure 2-2 show the key Vision 65/75 components. 
    Figure 2-1. Vision 65/75 Front/Side/Top View
    1.EXHAUST VENT
    2.ZOOM TAB  
    Use this to change the projected image size. 
    3.TOP IR SENSOR
    4.LAMP LED 
    Indicates lamp status as follows:
     Off during normal operation
     Red when the lamp has exceeded its usage life or developed a problem
    2Controls and Functions
    12
    7 8 9 10
    56
    43 
    						
    							Controls and Functions
    6 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
    5.POWER/STANDBY LED 
    Indicates power status as follows:
     Orange when the projector is in standby mode
     Flashes green for approximately 45 seconds after the projector is turned on to indicate 
    that the lamp is warming up
     Green during normal operation
     Flashes orange for approximately 110 seconds after the projector is turned off to 
    indicate that the lamp is cooling down
     Red when an internal failure requiring service has occurred
    6.TEMP LED 
    Indicates fan status and internal temperature as follows:
     Off during normal operation
     Red when internal temperature is too high or a fan failure occurs
    7.INTAKE VENT
    8.VIDIKRON LOGO  
    The logo can be rotated to match the projector 
    orientation: inverted (ceiling-mounted) or upright. 
    To rotate the logo, grip it at the sides, pull it away 
    from the projector and rotate it 180 degrees. 
      
     
    9.FRONT IR SENSOR
    10.PROJECTION LENS  
    To adjust the focus, grasp the lens by the outer ring and rotate it. 
    						
    							Controls and Functions
    Vidikron Vision Model 65/Model 75 Installation/Operation Manual 7 
    Figure 2-2. Vision 65/75 Rear/Bottom/Side View
    1.CABLE ACCESS DOOR 
    Open to access connectors. 
    2.DOOR RELEASE BUTTON
    3.CABLE OPENING 
    Pass cables through this opening.
    4.LAMP MODULE COVER 
    Remove this cover to access the lamp compartment.
    5.FRONT/REAR ADJUSTERS 
    Use these to adjust the projector height or projection angle.
    6.CEILING MOUNT HOLES  
    Use these to attach the ceiling bracket to the projector.
    4321
    565 
    						
    							Controls and Functions
    8 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
    2.2 
    Vision 65/75 Rear Panel
    Figure 2-3 shows the Vision 65/75 rear panel.
    Figure 2-3. Vision 65/75 Rear Panel
    1.HDMI 1 (Digital) 
    HDCP-compliant digital video input for connecting a DVD player or HD tuner with a DVI 
    or HDMI output.
    2.HDMI 2 (Digital)
    3.COMP 1 (RCA connectors) 
    Standard- or high-definition (480i/480p/576i/576p/720p/1080i/1080p) Component 
    (YPrPb) input for connecting a DVD/HD-DVD/BD player, HD set-top box or other SD/HD 
    source.
    4.COMPOSITE VIDEO INPUT 
    Standard composite video input for connecting a VCR, laser disc player or other 
    composite video source.
    5.S-VIDEO  
    A standard S-Video input for connecting a DVD player, satellite receiver or Super VHS 
    (S-VHS) VCR. 
    6.POWER INPUT (100 to 240 VAC) 
    Connect the Vision 65/75 to power here. 
    7.MAIN POWER SWITCH 
    Disconnects or applies power to the Vision 65/75.
    8.RS-232 CONTROL PORT 
    A female, RJ-11 connector for interfacing with a PC or home theater automation/control 
    system. 
    S-VID /S-VID
    1234567
    8910 
    						
    							Controls and Functions
    Vidikron Vision Model 65/Model 75 Installation/Operation Manual 9 
    9.12-VOLT (250 mA) TRIGGER OUTPUT (3.5-mm, mini phono jack)  
    Connection for a 12-volt trigger-controlled device. This can be a retractable screen, 
    screen mask or the Vidikron CineWide with AutoScope system. 
    10.COMP 2 / RGB 
    Five BNCs for connecting either RGB or component (YPbPr), SD or HD video signals. (The 
    Vision 65/75 automatically detects the signal format.) 
    2.3 
    Vision 65/75 Remote 
    Control
    Figure 2-4 shows the Vision 65/75 remote control, and the paragraphs that follow describe its 
    functionality.
    Figure 2-4. Vision 65/75 Remote Control
    FOCUS   LENSZOOM
    LIGHT
    OFF ON
    VID S-VID COMP1
    HDMI
    RGB
    INFO VAC
    ENTER
    EXIT MENU
    BRT
    CONT             COL               TINTHDMI 2COMP2
    CUST1           CUST2 ISF
    DAY ISF
    NIGHT
    16 : 9IWIDE
    LBOX
    4 : 3
    CINEMAIWIDE
    2.35
    PIP               ACT              PIP +              PIP -
    2
    1
    5
    46 3
    9
    80 7
    LENS
    1
    4
    9
    2
    3
    5
    7 6
    8
    10 
    						
    							Controls and Functions
    10 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
    1.LIGHT  
    Press to illuminate the buttons. 
    2.ON / OFF 
    Use these buttons to turn the projector on or off.
    3.Source Selection Buttons: 
     
    VID 
    Press to select Composite video input as the source.  
     
    S-VID (S-Video) 
    Press to select the S-Video input as the source.  
     
    COMP1  
    Press to select Component 1 video input as the source.  
     
    COMP2  
    Press to select Component 2 video input as the source.  
     
    RGB  
    Press to select the Component 2 RGB input.  
     
    HDMI / HDMI 2 
    Press to select an HDMI input. 
    4.INFO 
    Displays active source, signal resolution, aspect ratio and other projector status 
    information.
     
     
    Cursor Keys (, , , )  
    Use these buttons to select items or settings, adjust settings or switch display patterns. 
     
    VAC (V2 Aperture Control) 
    Adjusts the lens aperture (iris) setting according to the ambient light level in the viewing 
    area.
     
     
    EXIT 
    Press to save menu item setting(s), exit the current menu and return to the previous one.  
     
    ENTER 
    Press to select a highlighted menu item or confirm a changed setting. 
     
    MENU 
    Press this button to show or hide the on-screen display (OSD) controls.  
    						
    							Controls and Functions
    Vidikron Vision Model 65/Model 75 Installation/Operation Manual 11 
    5.Picture Adjustment Buttons:  
     
    BRT (Brightness) 
    Press to adjust black level.  
     
    CONT (Contrast) 
    Press to adjust white level.  
     
    COL (Color) 
    Press to adjust color intensity.  
     
    TINT 
    Press to adjust color hues. 
    6.Memory Preset Buttons: 
     
    ISF NIGHT 
    Press to recall settings for the current input from the “ISF Night” memory preset.  
     
    ISF DAY 
    Press to recall settings for the current input from the “ISF Day” memory preset. 
     
    CUST1 / CUST2 
    Press to recall settings for the current input from the “Custom 1” or “Custom 2” memory 
    preset. 
     
    7.Aspect Ratio Selection Buttons 
    Use these buttons to select an aspect ratio directly, as follows:  
     
    16:9 
    For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.  
     
    4:3 
    Scales the input signal to fit 4:3 display mode in the center of the screen.  
     
    LBOX (Letterbox) 
    For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.  
     
    IWIDE (IntelliWide) 
    Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display. 
     
    CINEMA  
    For viewing 2.35:1 source material.  
     
    IWIDE 2.35 (IntelliWide 2.35 – CineWide-equipped projectors only) 
    Selects the IntelliWide 2.35 aspect ratio, used for viewing 16:9 source material on a 2.35:1 
    screen. 
    8.0 - 9 
    Use these keys to enter menu passcodes. 
    						
    							Controls and Functions
    12 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
    9.Picture-In-Picture (PIP) Controls: 
     
    ACT 
    Press to switch to the active window in PIP mode. 
     
    PIP 
    Press to activate PIP mode.  
     
    PIP+ 
    Press to enlarge the PIP window. 
     
    PIP- 
    Press to shrink the size of the PIP window.
    10.LENS 
    Press to access the lens shift controls. 
    						
    							Vidikron Vision Model 65/Model 75 Installation/Operation Manual 13 
    3.1 
    Remote Control
    To install batteries in the remote control, push the 
    battery cover and slide it off. Install the two AAA 
    batteries with the correct polarity and then replace 
    the cover. 
    Notes on Batteries Make sure that the battery polarities are correct when installing the batteries.
     Do not mix an old battery with a new one or different types of batteries.
     If you will not use the remote control for a long time, remove the batteries to avoid 
    damage from battery leakage.
    Notes on Remote Control 
    Operation
     Make sure that there is nothing obstructing the infrared beam between the remote 
    control and the IR receiver on the projector.
     If the effective range of the remote control decreases, or it stops working, replace the 
    batteries with new ones.
     The remote control may fail to operate if the infrared remote sensor is exposed to bright 
    sunlight or fluorescent lighting.
     Ambient conditions may possibly impede the operation of the remote control. If this 
    happens, point the remote control at the projector, and repeat the operation.
    3Installation 
    						
    							Installation
    14 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
    3.2 
    Quick Setup
    Table 3-1 gives a quick overview of the Vision 65/75 installation process. The sections 
    following this one provide detailed instructions. 
       
    Installation should be performed by a qualified custom video installation 
    specialist.
    Table 3-1. Installation Overview 
    StepProcedureFor Details, Refer to 
    page...
    1Choose a location for the projector15
    2
    If installing a CineWide-equipped projector: Install 
    AutoScope lens motor or fixed CineWide base plate 
    (optional)19
    3Mount the projector25
    4Connect signal sources to the Vision 65/7527
    5Connect external controller to RS-232 port (optional)30
    6Connect 12-volt trigger output to AutoScope lens motor or 
    other equipment (optional)31
    7Apply power to the projector 32
    8Primary lens adjustments: focus, projected image size (zoom) 
    and position (shift) 18, 33
    9Change the OSD Language (optional)33
    10For rear-screen and/or ceiling-mount installations, select the 
    proper picture orientation 33
    11Install CineWide anamorphic lens (optional)34
    12CineWide lens adjustments: position, pitch (angle), geometry 
    and focus35
    13
    Projector calibration: adjust the following for each input, 
    starting with Component 1; save settings when finished:
    Aspect ratio
    Brightness
    Contrast
    Color level
    Tint
    Input position
    51 through 56
    Note 
    						
    All Vidikron manuals Comments (0)

    Related Manuals for Vidikron Projector Vision Model 65 User Manual