Vidikron Projector Vision Model 50 User Manual

31Vidikron Vision Model 50 Owner’s Operating Manual

Using the Menus•  Press MENU to open or close the on-screen 
menu.
•  Use the arrow buttons ( ▲,◄,▼,►) to select 
menu items or make adjustments.
•  Press ENTER or ► to enter the setting of items 
in the menu, or press  EXIT to leave and save 
the setting of items in the menu.
For more information on settings, See “On-
Screen Display Menus” on page 33.
Basic Operation
Selecting the Input 
Source
PIP / PBP Function
•  When you turn on the projector, it...

32Vidikron Vision Model 50 Owner’s Operating Manual

Turning off the Power
Basic Operation•  Press OFF to turn off the projector.
•  The  POWER LED will blink green and the 
fans will speed up for a quick cool-down. The 
projector will not respond to any command 
for 90 seconds.
•  The  POWER LED will light solid orange once 
the cooling down cycle has completed.
•  The fans will run for three minutes to cool.
•  You can turn the projector back on after 
approximately two minutes. 

33Vidikron Vision Model 50 Owner’s Operating Manual

Vision Model 50
Picture AdjustImage Option
Projector Status InstallationService
ISF Calibration
On-Screen Display Menus
Using the MenuThis unit is equipped with an on-screen display 
(OSD) menu for making adjustments and changing 
settings. There are five menu languages; see 
the Language setting under “Installation” on 
page 40.
•  Press  MENU to turn on/off the OSD menu.
  NOTE: If the Main Menu is displayed, you can also press 
EXIT to turn it off....

34Vidikron Vision Model 50 Owner’s Operating Manual

On-Screen Display Menus
Picture Quality 
AdjustmentsVision Model 50
Picture AdjustImage Option
Projector Status InstallationService
ISF Calibration
Brightness
 
Contrast
Color
 
Tint
Sharpness 
Picture Adjust
Brightness   26
Contrast 
  15
Color 
  31
Tint  
  14
Sharpness 
  2
Color Temp. 
  2
Color Select  NTSC
To access basic picture quality adjustments, press  MENU, select  Picture Adjust  and press 
ENTER. The picture quality sub-menu...

35Vidikron Vision Model 50 Owner’s Operating Manual

The Vision Model 50 has six memory settings for Color Temperature. Four of these settings 
are factory set to default as follows:
 0 -- Original lamp color temperature
 1 -- 5400 kelvins
 2 -- 6500 kelvins
 3 -- 8500 kelvins
 4 -- Custom
 5 -- Custom
Custom 4 and 5 memory are installer-adjustable and can be used to create custom settings. 
There are nine adjustable “white balance” parameters available for the Custom 4 and 5 
settings (three each for...

36Vidikron Vision Model 50 Owner’s Operating Manual

Image OptionsVision Model 50
Picture AdjustImage Option
Projector Status InstallationService
ISF Calibration
Active Image Area
Ac tive 
Image Area
Active Image Area
Image Option
Input Select
Aspect Ratio SD EnhanceVideo Filter
HD/RGB Adjust Blue Enable
Save Settings
Load Saved Settings
To access additional image settings, press  MENU, then press the ▲ or ▼ arrows to highlight 
Image Option  and press ENTER. The Image Option sub-menu then appears (see...

37Vidikron Vision Model 50 Owner’s Operating Manual

On-Screen Display Menus
• Cinema
The  image  in  the  Letterbox  mode  is 
enlarged to a 16x9 image and the upper 
and lower portions are compressed.
• Cinema Fill
A 2.35 image is stretched vertically in both 
directions to fill a 16:9 image.
SD Enhance
H Enhance   0
V Enhance 
  0
C Enhance 
  64
H Threshold 
  10
V Threshold 
  10
C Threshold 
  10
 SD EnhanceThe SD Enhance menu gives you options for improving 
the quality of standard-definition,...

38Vidikron Vision Model 50 Owner’s Operating Manual

Press ENTER  to display the  HD/RGB Adjust  menu. Use these 
settings to fine -tune 480p and higher-resolution signals for 
optimum picture quality.
• Auto:  To adjust the phase, frequenc y and position 
automatically, highlight “YES?” and press  ENTER.  
•  Freq.:  Adjusts the frequency of the signal.
• Phase:  Adjusts the phase of the input signal (similar to 
tracking on a VCR).
•  H. Pos.:  Adjusts the horizontal position of the image.
•  V. Pos.:...

39Vidikron Vision Model 50 Owner’s Operating Manual

On-Screen Display Menus
Projector StatusVision Model 50
Picture AdjustImage Option
Projector Status InstallationService
ISF Calibration
 Default
Sleep Timer
Lamp Hours
Projector Status
Default     Load
Sleep Timer        30 Minutes
Lamp Power    200 W
Lamp Hours    +8 Hours
        0 Minutes
To load default settings, configure the sleep timer or adjust the lamp, press  MENU, then 
press the ▲ or  ▼ arrows to highlight  Projector Status and press...

40Vidikron Vision Model 50 Owner’s Operating Manual

On-Screen Display Menus
InstallationVision Model 50
Picture AdjustImage Option
Projector Status InstallationService
ISF Calibration
Language

Picture Configuration
Keystone
Installation
Language
Picture Configuration Keystone
OSD Position OSD Timer
PIP/PBP Setup
Background Color
To access the Installation menu, press  MENU, then press the ▲ or  ▼ arrows to highlight 
Installation  and press ENTER. The Installation sub-menu will then appear (see...