Vidikron Projector Vision Model 150 User Manual

Installation
Vidikron Vision 150 Owner’s Operating Manual 59 
PREL
IMINARY
3.13 
Working With the Lamp 
Access the Lamp Adjust menu to: 
 Choose a lamp mode for regulating power and light output.
 Change the optical aperture size.
 View information pertaining to past and present lamps.
 Record the lamp serial number in the projector’s memory. 
Lamp Hours (read-only): Lamp Hours shows the number of hours logged on the current 
lamp. Whenever you record a new lamp serial number, the Vision 150...

Installation
60 Vidikron Vision 150 Owner’s Operating Manual
PREL
IMINARY
Lamp Mode: Select the Lamp Mode you want to use in order to control the light output. 
You can choose to run the lamp as bright as possible, you can power the lamp with a specific 
wattage appropriate for the installed lamp or you can set a specific intensity (brightness) to 
maintain. Keep in mind that higher lamp power settings can shorten lamp life.
Use the lamp mode that best suits your brightness needs:
•Max Brightness: The...

Installation
Vidikron Vision 150 Owner’s Operating Manual 61 
PREL
IMINARY
For example, a 1000-Watt lamp can be driven at no more than 1000 Watts. To produce 
desired brightness at the screen, a new lamp would likely need less than this maximum 
rating — perhaps 812 Watts (example only). Over time, however, the lamp requires more and 
more current in order to generate the desired light, until eventually the lamp wattage 
reaches its 1000-Watt maximum and the lamp power automatically levels off. At this...

Installation
62 Vidikron Vision 150 Owner’s Operating Manual
PREL
IMINARY
Notes: 

Vidikron Vision Model 150 Owner’s Operating Manual 63 
PREL
IMINARY
4.1 
Using the On-Screen 
Menus
Press the MENU button on either the remote control or the VHD Controller front panel to 
display the Main Menu. 
To select a menu item, use the  and  buttons on either the remote control or the VHD 
Controller front panel to highlight it. Press ENTER to confirm your selection. 
The Vision 150 OSD menus are arranged hierarchically, as shown in Figure 4-1. Depending on 
the selected input source and signal...

Operation
64 Vidikron Vision Model 150 Owner’s Operating Manual
PREL
IMINARY
Figure 4-1. VHD Controller OSD Menu Structure for Vision 150
Service
Test VideoGrey Bars 1
Grey Bars 2
Color Bars 1
Color Bars 2
Input Names Rename, Restore or Save
Remote ControlPrimary
Secondary
Display Device: ConfigureInstallationPicture Orientation
Keystone
Lamp Hours (read-only) 
LensFocus
Zoom
Shift 
Auto Setup
HD FormatHD/RGB 1
Auto, RGB or YUV
HD/RGB 2
ADC Bandwidth Auto, 75 MHz, 150 MHz or 300 MHz
YPbPr Input...

Operation
Vidikron Vision Model 150 Owner’s Operating Manual 65 
PREL
IMINARY
Main MenuThe Main Menu is the starting point for accessing all projector functions. 
(The Calibration and Service menus are hidden and not accessible until you enter a 
passcode.) 
Input SourceFrom the Main Menu, select Input Source to choose a video signal source. 
The active source is indicated by an arrow (>) to its left; in this example, Composite is the 
active source. 
Aspect Ratio To change the aspect ratio (size and...

Operation
66 Vidikron Vision Model 150 Owner’s Operating Manual
PREL
IMINARY
Table 4-1. Aspect Ratio Settings 
Aspect Ratio
Remote 
Control
Key
Description
16:916:9Select 16:9 to view 16:9 DVDs 
and HDTV programs in their 
native aspect ratio. 
4:3 images are stretched 
horizontally to fit a 16:9 
screen. 
4:34:34:3 scales the input signal to fit 
in the center of the 16:9 
screen. 4:3 is the aspect ratio 
used by computer monitors, 
standard television 
programming and most VHS 
video cassettes....

Operation
Vidikron Vision Model 150 Owner’s Operating Manual 67 
PREL
IMINARY
CinemaCINEMASelect Cinema to view 2.35 
source material in its native 
aspect ratio.
With a 16:9 screen and a 
non-CineWide projector (no 
anamorphic lens), the upper 
and lower portions of the 
screen are masked, but the 
geometry of the active image 
area is unchanged.
With a 2.35:1 screen and a 
CineWide-equipped projector, 
the VHD Controller scales the 
2.35:1 image so that the active 
image area fills the 16:9 chip...

Operation
68 Vidikron Vision Model 150 Owner’s Operating Manual
PREL
IMINARY
PictureUse the controls in the Picture Menu to calibrate your Vision 150 for optimum picture quality.
The Vision 150 has been designed to incorporate setup and calibration standards established 
by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted, 
industry-recognized standards for optimal video performance and has implemented a 
training program for technicians and installers to use these standards...