Vidikron Projector Vision Model 15 User Manual

Controls and Functions
Vidikron Vision Model 15 Installation/Operation Manual 7 
1.12-VOLT (250 mA) TRIGGER OUTPUT (3.5-mm mini phono jack; Tip = +12V; Sleeve = 
Ground)
 
Connection for a retractable screen, screen mask or other, 12-volt trigger-activated 
device.
2.RS-232 CONTROL PORT 
A female, 9-pin mini-DIN connector for interfacing with a PC or home theater 
automation/control system. 
3.COMPOSITE VIDEO INPUT 
Standard composite video input for connecting a VCR, laser disc player or other...

Controls and Functions
8 Vidikron Vision Model 15 Installation/Operation Manual
2.3 
Vision 15 Remote Control
Figure 2-3 shows the Vision 15 remote control, and the paragraphs that follow describe its 
functionality.
Figure 2-3. Vision 15 Remote Control
EXIT
L-BOX
I-WIDECINEMA
I-WIDE
2.35
CUSTISF
NTISF
DAY
123
4
56
789
0
LIGHTDEF
MENUON
OFF
COMP
DVI-AS-VIDVIDEO
DVI-D
HDMI
16:9
4:3
SOURCE
ASPECT
MEMORY
1
2
3
4
5
6
7
8
9
10
15
14
13
12
11 

Controls and Functions
Vidikron Vision Model 15 Installation/Operation Manual 9 
1.ON / OFF 
Press to turn the projector on or off.
2.IR OUTPUT INDICATOR 
Lights when a button is pressed to indicate that an IR signal is being transmitted.
3.Source Selection Buttons: 
 
VIDEO 
Press to switch to the Composite video input. 
 
S-VIDEO 
Press to switch to the S-Video input. 
 
COMP 
Press to switch to the Component (480i/480p/576i/576p/720p/1080i/1080p) video 
input.
 
 
DVI-A 
Press to switch to the DVI-A...

Controls and Functions
10 Vidikron Vision Model 15 Installation/Operation Manual
8.MENU 
Press this button to access the on-screen display (OSD) controls.
9. Not used.
10.LIGHT  
Press this button to illuminate the buttons. 
11.CUST 
Press to recall settings for the current input from the “Custom” memory preset. 
12.ISF NT  
Press to recall settings for the current input from the “ISF Night” memory preset. 
13.Cursor Keys (, , , )  
Use these buttons to select items or settings, adjust settings or switch...

Vidikron Vision Model 15 Installation/Operation Manual 11 
3.1 
Remote Control
To install batteries in the remote control: 
1. Press down the tab on the cover and 
pull the cover in the direction of the 
arrow.
 
 
 
2. Insert the included batteries. Ensure that 
the polarities correctly match the 
 
and  markings inside the battery 
compartment. 
3. Insert the lower tab of the cover into the 
opening, and press down the cover until 
it clicks in place.
Notes on Batteries Make sure that the battery...

Installation
12 Vidikron Vision Model 15 Installation/Operation Manual
Notes on Remote Control 
Operation
The remote control can be used to control the projector within the ranges shown in Figure 
3-1. 
Figure 3-1. Available Range of the Remote Control
 For best results, hold the remote control within 23 feet (7m) of the back or top sensor and 
aligned within 30°.
 Do not drop the remote control or expose it to moisture or high temperature.
 The remote control may malfunction under a fluorescent lamp. If...

Installation
Vidikron Vision Model 15 Installation/Operation Manual 13 
3.2 
Quick Setup
Table 3-1 gives a quick overview of the Vision 15 installation process. The sections following 
this one provide detailed instructions. 
   
Installation should be performed by a qualified custom video installation 
specialist.
Table 3-1. Installation Overview 
StepProcedureFor Details, Refer to 
page...
1Choose a location for the projector14
2If installing a Vision 15ET/CineWide: Install CineWide lens 
base plate...

Installation
14 Vidikron Vision Model 15 Installation/Operation Manual
3.3 
Installation Considerations
Proper installation of your projector will ensure the quality of your display. Whether you are 
installing a projector temporarily or permanently, you should take the following into account 
to ensure your projector performs optimally.
Installation TypeChoose the installation type that best suits your needs: front or rear screen, floor mount or 
inverted mount. 
Table 3-2 compares these various...

Installation
Vidikron Vision Model 15 Installation/Operation Manual 15 
Throw DistanceThrow distance is the distance measured from the front of the projector to the screen. This is 
an important calculation in any projector installation as it determines whether or not you 
have enough room to install your projector with a desired screen size and if your image will 
be the right size for your screen.
You can quickly estimate the throw distance by taking the width of the screen and 
multiplying it by the...

Installation
16 Vidikron Vision Model 15 Installation/Operation Manual
Vertical and Horizontal 
Position
Proper placement of the projector relative to the screen will yield a rectangular, 
perfectly-centered image that completely fills the screen.
Typically (but not always), the projector is positioned perpendicular to the screen and in such 
a way that the lens center and screen center are aligned with each other, as shown in 
Figure 
3-3.
Figure 3-3. Projector Placement
➤
Height
Projection...