Vidikron Projector Vision Model 10 User Manual

Operation
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 41 
PREL
IMINARY
Color Temperature: To adjust the color temperature, select Color Temp from the Picture 
Adjust menu and press ENTER. (Color temperature defines the “color of gray.”) The range is 
from 5,000K to 10,000K, in increments of 500K. The default setting, 6,500K, is appropriate for 
most situations. Higher settings produce a “bluer” picture; lower ones impart a reddish hue 
to the image.
For more precise control over the color...

Operation
42 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
ICC Select: Choose ICC Select from the Picture Adjust menu to specify the color space 
(Standard, NTSC, HDTV or PAL) that is appropriate for the source signal, to achieve optimal 
color balance.
If you select NTSC, HDTV or PAL, you can make further adjustments to individual color  space 
characteristics in the 
ICC Adjust sub-menu under the ISF Setting menu, described later in this 
section. (The Standard color space is...

Operation
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 43 
PREL
IMINARY
• Auto Tune: Auto Tune automatically adjusts settings to optimize computer images. Auto 
Tune can be executed either on command or automatically whenever an incoming RGB 
signal is present. To execute Auto Tune on command, select Execute Auto Tune and press 
ENTER. To enable automatic Auto Tune, select Auto Tune and set it to ON. 
Image Position: To adjust the horizontal and vertical position of the projected image,...

Operation
44 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
Information: Select Information from the Main Menu to see information about the current 
source, input resolution, horizontal and vertical frequencies, lamp hours and the installed 
firmware version. 
Should you ever need to contact Vidikron Technical Support, this information will help them 
answer your questions or resolve product performance issues. 
Restore Factory Settings: To reset all items in the Image Options...

Operation
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 45 
PREL
IMINARY
Keystone Correction: If the projector and screen are not installed perpendicular to each 
other, the image may become distorted in a trapezoidal shape, as shown in 
Figure 4-10. 
Select Keystone from the Installation menu to compensate for this. 
Figure 4-10. Horizonal and Vertical Keystone Correction
Fan High Speed Mode: If the projector is being used in a high-altitude environment, use Fan 
High Speed Mode to prevent...

Operation
46 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
ISF Setting Use the ISF Setting menu to perform advanced picture quality adjustments. This menu 
should be used by ISF-certified technicians only. 
Several controls in this menu are identical to those in the Picture Adjust menu, but are 
accessible only by entering the ISF Calibration menu passcode. This makes it possible to 
restore the picture quality settings to what they were when the projector was installed, 
simply...

Operation
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 47 
PREL
IMINARY
ICC Adjust: Use the ICC Adjust controls to customize the stored NTSC, HDTV and/or PAL 
color space characteristics. To do this:
1. Select ICC Adjust from the ISF Calibration menu and press ENTER. 
2. Select the color space to modify using the left- or right-arrow buttons. 
3. Select a component color (Red, Green, Blue, Cyan, Yellow or Magenta).
For each component color, you can adjust the following:
•Intensity: This...

Operation
48 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
Blue Enable: Refer to Blue Enable on page 44. 
Splash Screen Timer: Press the right- or left-arrow buttons to set the Splash Screen Timer. 
This timer controls how long the startup (ISF and Vidikron logo) image stays on-screen after 
you turn on the projector. Select from 15 to 60 seconds, in 5-second increments.
Noise Reduction: To apply Digital Noise Reduction (DNR) to the input signal, select Noise 
Reduction from the...

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 49 
PREL
IMINARY
5.1 
Cleaning the Projector
Unplug the power cord before cleaning the 
projector.
 Avoid using benzene or thinner, as these can 
damage the finish on the projector exterior.
 Do not use volatile agents, such as insecticides, 
on the projector.
 Do not leave rubber or plastic objects in contact 
with the projector for long periods as they may 
damage the finish of the projector.
Wipe off dirt gently with a soft flannel...

Maintenance and Troubleshooting
50 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
5.3 
Cleaning the Intake and 
Exhaust Vents
This Vision 10/12 is equipped with intake and 
exhaust vents to allow the flow of cool air 
through the projector and maintain the 
proper operating temperature.
You should periodically clean the vents by 
vacuuming them with a vacuum cleaner. 
Vidikron recommends doing this after every 
100 hours of use, or more often if the 
projector is used in a dirty...